研磨的

In this thesis, the side-polishing coupler is designed; the polishing process and some points for attention are presented.

此外，文中重点介绍了边研磨光纤耦合装置的设计方案，具体的边研磨过程以及相关注意事项。

Grinding valve hole (1) research with Mainly to restore valve grinding hole geometry, eliminating valve hole taper and ellipticity.

研磨阀孔(1)研具研磨主要是恢复阀孔的几何尺寸，消除阀孔的锥度和椭圆度。

Magnetic abrasives are composite abrasives which must be magnetizable and abrasive.

磁性研磨材料必须具备有被磁化性质及有研磨能力的复合磨料，磁化性良好的物质如铁、钴、镍。。

ResultsThe best packed method was trituration and the best packed preparation conditions were as follows:β-CD :volatile oil=10g:1ml,adding 3 times water,triturating 3 hours.

结果优选出的包合方法为研磨法，最佳包合工艺条件为：βCD与挥发油的投料比为10 g∶1 ml，加3倍量水，研磨3 h。

Specialist high performance grinding oil for servere grinding applications of steels and yellow metal s.

特殊的优质高速研磨加工油，适合于钢材和有色金属的重负荷研磨加工。

FeSi nanoparticles were synthesized via thermal decomposition of iron pentacarbonyl in the solution of dioctyl ether, stabilizers oleic acid and oleylamine. The TEM images showed that FeSi nanoparticles had cubic shape, but it seemed that the composition was not uniform. According to the EDS results, the Fe:Si ratio of gray-uniform nanopaiticles was almost 1:1, and blacker FeSi nanoparticles contained more Fe atoms. Although FeSi didn't have uniform structure, it still could be proved that the incorporation of Fe and Si existed in a single nanoparticle. All possible structure, lattice, binding, morphology, surface condition would be discussed. These results indicated that perhaps FeSi2 was the main structure of the new products; however, due to incompletely combination and less synthesized time, it might still contain some part of Si and Fe structure. Besides, FeSi nanoparticles preserved the optical properties from Si atoms, but the PL intensity was much lower. The maxima PL peak appeared at 388 nm with the excitation at 300 nm. Their saturation magnetization, remanent magnetization and coercivity were measured by the SQUID, exhibiting their nearly superparamagnetic behavior.

利用热裂解系统可成功将研磨矽奈米粒子及五羰铁结合，制备出铁矽奈米粒子；从穿透式显微镜照片可知其粒子呈现立方体型态，但颜色深浅及组成不均，EDS结果则显示颜色均匀之粒子铁与矽之组成大致为1：1，颜色较深之粒子则含有较高量的铁元素；尽管组成比例并不统一，但单颗粒子同时含有矽与铁两种元素，初步说明铁矽奈米粒子之形成；进行多种结构与表面分析并探讨所有可能之键结、结构及表面元素后，推测铁矽奈米粒子可能以FeSi2之结构形成，并同时包含未重组完成的矽及铁之结构；利用PL分析得知铁矽奈米粒子确实保留矽之放光特性，并在300 nm激发光源下，於波长388 nm处有一最强放光特性峰，但整体发光效益不及研磨矽奈米粒子之结果；最后，利用超导量子干涉磁化仪量测其饱和磁化量、残留磁化量、与矫顽磁力，发现磁滞现象并不明显而几乎呈超顺磁性。

Based on above work, theGET—500 integral graphite electrodes abrading tool is designed.

在上述工作的基础上，设计了&GET—500整体石墨电极研磨机&，并对其制造装配精度、工作控制及动态特性进行了系统的理论分析和实验研究，成功地研制了我国第一台石墨电极研磨机。

Based on above work , the GET— 500 integral graphite electrodes abrading tool is designed . It is systematically analyzed in theory and researched by experiments on the precision of manufacturing and assembling , working control and dynamic characters.

在上述工作的基础上，设计了&GET-500 整体石墨电极研磨机&，并对其制造装配精度、工作控制及动态特性进行了系统的理论分析和实验研究，成功地研制了我国第一台石墨电极研磨机。

Compared with the prior art, the preheating method preheats the reaction system to an optimal reaction temperature by the deionized water or the grinding fluid with certain temperature and does not need to preheat the reaction system by grinding dummy wafers.

与现有技术相比，本发明预热方法通过带有一定温度的去离子水或者研磨液将反应系统加热到最佳的反应温度，不需要通过研磨一些空挡片进行预热。

Three dimensional simulations were made in 5-hole nozzle s which were skived by fluild former and later by means of AVL FIRE software.

并在CA498柴油机上进行了5孔挤压研磨喷油嘴的对比试验研究，试验结果表明，挤压研磨喷油器在满足排放的前提下，改善了经济性指标。

On closer examination, though, this is not a vote for multilateralism but just the opposite.

仔细审视后我们发现，这并非是对多边主义投出的赞成票，而是恰好相反。

Uncovering their weak spots, so I can defeat them.

揭露出他们的弱点，这样我就可以打败他们了。