英语人>网络例句>研磨的 相关的搜索结果
网络例句

研磨的

与 研磨的 相关的网络例句 [注:此内容来源于网络,仅供参考]

Measure the result as follows: Ra(Surface roughness of steel ball)=0.015 u m, wavmess=0.06 um,△Sph=0.010 u m, VDWL=0.015 u m. The flocculus steel balls measured were assembled in Luoyang Precise Bearings Company. The results show that the bearing vibration values reached Z2 group near 98%, the bearing vibration values with new technique balls tower above sixty percentile than grindtechnics.

然后对加工出的"绒面"钢球在洛阳轴承集团进行了合套测振试验,测振试验结果表明:振动值达到Z2组的比例达到98%,比用研磨工艺制得的钢球合套后测得的振动值数据高出60个百分点;振动值达到Z3组的比例高达到83~97%,比用研磨工艺制得的钢球合套后测得的振动值数据高出77~90个百分点。

When other technics conditions are certain, we use the globosity aluminum powder of different particle diameter a to grind the flake of aluminum powder , with the particle diameter increase of the globosity aluminum powder, the particle diameter of the flake of aluminum powder will also become bigger immediately. 3, The ratio of grinding ball to aluminum powder is 20:1. 4,the grinding speed is 38 and 33 r.min alternate once h-our in the first 10 hours, and use the speed of 29 and24 per hour alternating revolving speed in the last 5 hours, this speed is fine to grind the flake of aluminum powder. 5, wet method ball-milling mainly adopt of help-milling agent as Bl. 6, influence of the research grinding time.

经系统的研究,得出如下结论:1、基本参数:采用200升球磨机,装入钢球200kg,原料铝粉:溶剂量=1:2,铝粉:钢球=1:20;2、当其它工艺条件一定时,用不同粒径的球状铝粉作为原料磨制片状铝粉,随着原料铝粉的粒径增大,所制得的片状铝粉的粒径也会随之增大。3、球料比我们控制在20:1.4、研磨前10小时采用速38和33r.min每小时交变一次,后5小时用29和24每小时交变的转速,这个速度是适宜磨制片状铝粉的。5、湿法球磨片状铝粉主要采用的助剂为复合助剂B1.6、研究研磨时间的影响。

With the development of IC fabrication technique, the feature size of the chip is getting down now. To make the feature size printable and avoid litho distortion, more resolution enhancement technology are used. Emerging RET are dramatically increasing the complexity of mask and layout, in return, more complex design rules are needed in physical verification.

随着IC制造技术的迅猛发展,芯片的特征尺寸不断的缩小,越来越多的分辨率提高技术被用于研磨版的制造,这些技术大大提高了研磨版的复杂度,也增加了版图物理验证的难度,在65nm及更先进的工艺中,传统的物理验证规则已经无法保证最终的良率。

First of all, the improving feeding helix can not only get material into the ball mill successfully, but also increase ventilated proportion; Secondly ,making use of all sorts of new scaleboards can reform the working condition of skive substance and raise the material adaptability; Third, separating storehouse board, have not only increased control material to flow, and balanced each storehouse smash the function of ability, but also realize thickness pellet grade role; Grind tail storehouse choose hyperboloid drum liner, in axial and circumference direction have incline curved surface, can not only increase steel ball lateral grade , but also still raise steel forge , steel ball grind efficiency.

进料口螺旋的改进,不仅解决了堵料现象,而且加大了通风面积;各种新型衬板的使用,对研磨体运动状态的调节以及对物料的适应性都有了较大的改善;隔仓板不仅增加了控制料流及平衡各仓粉碎能力的功能,而且可以实现粗细颗粒的分级作用;磨机尾仓选用双曲面衬板,在轴向和圆周方向均有倾斜曲面,不仅能够增加钢球的横向分级,还能提高钢锻、钢球的研磨效率。

The experiment results showed that, the MnO_2 particles scattered uniformally after milled for 6h, the average diameter was 300nm, which loaded on the surface of fiber in flat successfully. The removal efficiencies to HCHO of MnO_2 milled for 6h was up to 94.07% after 72h, the removal efficiencies increased with the content of MnO_2 loaded, its increased after treated with DMF, or so was 7%.

实验结果表明,研磨6h的MnO_2粉末分散均匀,平均粒径可达300nm,以平铺的形式均匀地负载于纤维上,效果比较理想;随着吸附时间的延长,研磨6h的MnO_2粉末反应72h对甲醛的去除率达94.07%;活性炭/腈氯纶负载MnO_2纤维对甲醛的去除率比未负载的明显提高;随着纳米MnO_2负载量的增大,甲醛的去除率变大,用DMF处理后的纤维对甲醛的去除率有所提高,大约提高7%。

The material is prepared by mixing barium titanate 80~99% and acetylene black 1~5% with PbO-B2O3 0~15% proportionally, grinding in agate grinder or in ball mill, press forming at pressure 2~10Mpa under vacuum or protecting gas environment.

按80%~99%的钛酸钡、1%~5%的乙炔黑和0%~1 5%的PbO-B2O3玻璃粉的比例混合后,在玛瑙研钵中研磨或者在球磨机中研磨,以压力为2~10MPa压制成型,该陶瓷材料的制备需要在真空或者保护气体的保护下进行。

In this study, it was found that optimum grinding occurs at 85% of critical speed, compared to the optimum grinding at 70% of critical speed of the ball mill in the cement factory.

在这一项研究,以下被发现:最适宜研磨以以水泥工厂的球压榨机的 70%紧要关头速度被与最适宜的研磨相较的 85%的紧要关头的速度发生。

It belongs to fuel processing technology field. It includes the following steps: using alumina industrial waste red mud as material; drying and grinding; adding red mud fine powder into 200-350 screen mesh coal powder by the weight of the former is 10-20% of the latter; mixing uniformly and spraying 5-10% water; forming coal ball by hydraulic press; its pressure is 10-30MPa.

本发明的氧化铝生产厂的废料赤泥为原料,烘干研磨,然后在一定量的200~350目的煤粉中添加上述赤泥细粉,加入量为煤粉重量的10~20%,经共同研磨混合均匀后,喷洒5~10%的水,再次混合均匀,随后用液压机将上述混合物压制成煤球;所用压力为10~30MPa;最终制成具有较高煤炭燃烧率的型煤。

In the old days, if you found overspray or any type of unwanted substance on the hood, roof or deck lid of your car that washing didn't remove, you could simply go to the garage and grab any old compound, and together with a rag, you could quickly remove the offending contaminants. After that you could simply apply just about any companies wax and presto-chango, the problem was gone.

在早期,如果你在你爱车的引擎盖、车顶、底盘上发现清洗不掉的喷涂物或任何令人讨厌的物质,你唯一能做的就是拿著你的旧式研磨剂去车库,然后使用抹布搭配研磨剂一起来快速的移除这些令人烦扰的脏污,之后你可以简单上些任何公司所生产的蜡品,转眼间就可以解决这样的问题

Grind the Pine needles, dried juniper berries and Cedar together with a pestle, add frankincense and mix well before burning on charcoal in a fireproof container.

首先,研磨松针,接着将弄干的杜松子和雪松放在一起,然后加入乳香并充分的研磨混合使它们均匀的混合在一起,最后将它们放入容器里用碳烧的方式慢慢蒸煮(关于容器,尽量选择一个耐受度高的,可以耐受高热和长时间蒸煮的容器

第12/61页 首页 < ... 8 9 10 11 12 13 14 15 16 ... > 尾页
推荐网络例句

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严,以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆,把帆卷起,系住。

Therefore, positively advances the interest rate marketability reform is one of current our country finance reform important tasks.

因此,积极推进利率市场化改革是当前我国金融改革的重要任务之一。