查询词典 shear angle

At last considering the effect of work piece and cutting speed the new shear angle model of aluminum alloy 7050-T7451 was established and proved to be more suitable for expressing the variety of shear angle in high speed cutting process.

最后，基于快速落刀实验和有限元仿真结果对高速切削剪切角模型的进行修正，综合考虑工件材料和切削速度对剪切角的影响，建立适用于铝合金7050-T7451的高速切削加工的切削方程式。

Early attempts to establish a mechanism with the shear angle related to theoretical models, such as the Merchant's proposed method of calculating shear angle, Lee and Shaffer made the slip-line field theory, etc.

早期机理研究试图建立起一种与剪切角相关的理论模型，如Merchant提出的剪切角计算方法、Lee和Shaffer提出的滑移线场理论等[1]。然而，到目前为止这些思路并没有取得令人满意的结果。

The critical shear angle of quasi-static state was given under different loading speeds and frame lengths condition, and the influence of specimen size on this shear angle range is also discussed.

在此基础上，提出了在特定的剪切范围内，可以将画框的运动看作是准静态过程进行处理的思想；得出了在不同拉伸速度和边框长度条件下装置处于准静态时的临界剪切角，并且分析了织物试样尺寸大小对准静态范围的影响。

As walk-off angle and acceptance angle of beam limit the conversion efficiency and the tunable wavelength range of difference frequency generation, research include effective nonlinear coefficient, walk-off angle and acceptance angle as functions of wavelength, the relationship between conversion efficiency and acceptance angle, and the impact of crystals length on the process of frequency conversion.

由于光束的走离角、允许角限制了转换效率和差频调谐波长范围，研究内容还涉及了有效非线性系数、走离角和允许角与波长的关系，转换效率与允许角的关系，以及晶体长度在频率变换过程中产生的影响。

Based on force diagram an analytical expression between some factors and splaying angle of the bar is brought forward, pointing out that splaying angle of the bar should be 2 3 degrees, and slitting angle should be 30 degrees approximately, outboard slant angle on the slitting groove should be 45 50 degrees and bite angle should be 7 8 degrees.

为稳定小规格带肋钢筋的三线切分轧制，对涉及棒材张开角的切分孔孔型诸角度进行了分析，通过对轧件受力状态的讨论，提出了诸因素与棒材张开角之间的解析式，指出满足三线切分稳定轧制时的棒材张开角应为 2°～ 3°，相应的孔型切分角为 30°左右，孔型外侧壁倾角应在 4 5°～ 5 0°之间，咬入角可控制在 7°～ 8°之间等。

Under the vertical load, the strength of rock mass is higher when there is only one group of joint and the dip angle is less than 20 or higher than 80; When dip angle is between 20 to 80, the strength of rock mass is much lower, it is smallest when dip angle is about 50, and it is lower when this kind of dip angle is in combination with other angle.

7在铅直向荷载作用下，岩体中只存在一组倾角小于20°或者大于80°时，岩体的强度相对较高；当岩体中存在一组节理的倾角在20°～80°间时，岩体的强度值很小，而且在与其他倾角的节理组合时，岩体的的强度值变化不太大，特别是当节理倾角为50°左右的时候，岩体的强度相对最低。

Exterior Opposite Angle Area : According to one angle area of the triangle, if we extend the two angle lines to the opposite direction, the area formed by the extending lines which like mirror area to the original angle is called here Exterior Opposite Angle Area.

外部对角映射区：针对三角形的一个角，将构成该角的两条相邻线段进行对角方向的虚线，这两条虚线围成的区域就是该三角形一个角的外部对角映射区。

Exterior Opposite Angle Area: According to one angle area of the triangle, if we extend the two angle lines to the opposite direction, the area formed by the extending lines which like mirror area to the original angle is called here Exterior Opposite Angle Area.

外部对角映射区：针对三角形的一个角，将构成该角的两条相邻线段进行对角方外部对角映射区向的虚线，这两条虚线围成的区域就是该三角形一个角的外部对角映射区。

With a dip angle between 15° and 30°, the uplift of an obducted plate during continental collision is much higher, and able to form a high mountain. The uplift is greatest with a dip angle of 15°; whereas with a dip angle between 30° and 45°, the subduction depth of a plate is much deeper, and able to form a deep basin. The subduction depth is greatest with a dip angle of 45°. When the dip angle is equal to or greater than 75°, subduction and obduction movements between two continents become undistinguishable.

当断裂带倾角在15~30°时，两个大陆板块碰撞导致的仰冲板块一侧隆升高度相对更大，利于形成高大的山脉，其中以15°倾角对应的仰冲板块一侧隆升最高；当断裂带倾角在30~45°时，两个大陆板块碰撞导致的俯冲板块的俯冲深度相对更深，利于形成深陷的盆地，其中以45°倾角对应的俯冲陆块一侧俯冲最深；当断裂带倾角≥75°时，两个大陆板块之间的相对俯冲和仰冲作用变得不明显。

Experiments exposed that the inner flow of tooth space in the micro-channels was proved to be cycled flow after fully development. For the more, low velocity vortex cavities existed in the vertex angle and inner side of bend angle of straight angle micro-channel, while back flow only appeared in the internal side of bend angle of round angle micro-channel. It's easy to take place deposition in the low velocity vortex cavities, which is the main cause of blocking.

试验发现各类微通道齿间内流充分发展后是一种重复性流动，平角微通道顶角和转角内侧存在低速涡旋区，圆角微通道只在转角内侧出现回流，颗粒在低速涡旋区易发生沉积，是造成堵塞的主要原因。

Mr. Putin said there were signs of genocide against the Ossetian people.

普京说，有迹象表明对南奥塞梯人进行了种族清洗。

What I'm trying to say, Tristan is...

特瑞斯坦。我想说的是。