查询词典 plane angle

In the typical setup of Michelson interferometer, turning the tested object a small angle generates an air wedge between the object plane and the reference plane. The wedge produces equal thickness interference fringes.

采用典型的迈克尔逊干涉光路，将物体偏转一微小角度（等效为物面与参考面间形成空气楔）产生等厚干涉，可在物体的表面引入包含物体高度信息的载波干涉条纹。

The problem of obtaining the dip angle of the plane figure to projection plane with Rytz Method is studied in this paper.

本文应用里茨作图法，研究由单面投影求平面图形对投影面的倾角问题

The said Martinez stretcher comprises concave spherical reflecting lens, plane reflecting lens and grating. The said compressor comprises plane reflecting lens, inner right angle reflecting lens and grating, which is characterized by the following: the grating fringe density of the stretcher is larger than that of the compressor.

所述的马丁内兹展宽器由凹球面反射镜、平面反射镜和光栅组成；所述的压缩器由平面反射镜、内直角形反射镜和光栅组成，其特征在于，展宽器的光栅条纹密度大于压缩器的光栅条纹密度；展宽器中的凹球面反射镜曲率半径位0.9～1.2米，光栅距凹球面反射镜的位置为凹球面反射镜曲率半径的1/3～1/2。

Rytz Method ; maximum oblique line ; Right-angled Triangle Method ; plane figure ; projection plane ; dip angle ; conjugate diameter

里茨作图法；最大斜度线；直角三角形法；平面图形投影面；倾角；共轭直径

In the design of the structure, a new 2-D scanning machine is put forward which has overcome the limit of common underwater TV system influenced by the environment of water. It can scan 360 degrees in horizontal plane and 90 degrees in vertical plane, and there isn't dead angle.

根据以上内容的研究和分析，在结构设计方面，提出了二维扫描机构，它克服了一般水下电视系统由于使用特殊环境的限制不能进行扫描的缺点，可以进行水平360度，垂直90度全方位扫描，并且不存在盲区。

The parity-violating energy difference of D- and L-alanine was undertaken as a function of the dihedral angle θ of the carboxylate plane with respect to the Cα-Hα plane.

自然界的力只有弱力是宇称不守恒的。在分子物理中，电弱力宇称不守恒是导致D-和L-丙氨酸能差的根源。

The in-plane equivalent elastic modulus and tensile strength of stitched composite laminates are studied, and its found that the in-plane equivalent elastic modulus decreases with the increase of stitch density, stitch thread diameter, maximal misalignment angle and the distortion width, and the range is about 5%. The tensile strength of stitched composite laminate increases with the increase of stitch step and decreases with the stitch space.

研究结果表明：随着缝纫密度、缝纫线直径、最大纤维偏转角和缝纫变形区宽度的增加，缝纫复合材料层合板面内等效模量逐渐降低，最大降幅一般在5%左右；缝纫复合材料层合板的拉伸强度随缝纫针距的增加而增大，随缝纫行距的增加而降低，因此缝纫密度对拉伸强度的影响程度要看具体的缝纫针距和行距。

Ecliptic plane and white plane, not the same, among them an average of 5 ° 09 angle, and always changing.

黄道平面与白道平面不是相同的，它们之间平均有5°09′的夹角，并且随时发生变化。

This paper presents the Machining Tool geometry of the former flank, the main flank, flank, the main cutting edge, Under the cutting edge tip cutting plane, the main section, the former Kok, horn, wedge angle edge angle, pointed knife, the blade angle, vice horn, Under the Frontier concept, the concept of cutting consumption, and the general circumstances of their choice method for processing slender shaft. cast iron materials, aluminum, stainless steel, rubber materials, plexiglass material, cloth bakelite materials, high temperature alloys, aluminum-magnesium alloy, hardened steel, the typical trapezoidal thread, the thread Triangle, Speaking at the trapezoidal screw thread pitch of the Tool geometry of the selection methods and cutting the amount of cutting fluids reasonable choice.

本文介绍了在机械加工中车刀几何角度中的前刀面、主后刀面、后刀面、主切削刃、副切削刃刀尖切削平面、主截面、前角、后角、楔角主偏角、刀尖角、刃倾角、副后角、副前角的概念、切削用量的概念、以及一般情况下的它们的选择方法，进行加工细长轴、铸铁材料、铝合金、不锈钢、橡胶材料、有机玻璃材料、夹布胶木材料、高温合金、铝镁合金、淬火钢、典型梯形螺纹、三角螺纹、特在螺距的梯形螺纹等的车刀几何角度的选取方法切削用量及切削液的合理选择。

Based on the definition of benchmark angle and compensation angle,the algorithm of roll angle of projectile in fire plane is brought out and the calculating error is analyzed.The simulation is carried out for the swing of projectile and the measurement of geomagnetic signal error.

将弹丸的滚转角分解为基准角和补偿角，给出了处于射击平面内的弹丸滚转角解算方法并进行了误差分析，针对弹丸的摆动及地磁信号测量误差进行了仿真。

He and Nina moved to California and lived at 2005 Ivar Street, Apt.

他和Nina搬到加州，并在2005年伊瓦尔街，公寓生活。

Droperidol （ potently inhibits transfected HERGchannels and this is the probable mechanism for QT prolongation.

氟哌利多有效地抑制了转染的 HERG 钾通道，可能是 QT 间期延长的机制。