查询词典 feedback amplifier

The principle of the amplifier is get the value of the feedback resistance which can change the gain of the amplifier , then make sure the relay on the right stall, we can get the expectation gain.

本设计实现增益控制的原理是根据OP37G的放大原理公式计算出实现指标增益所需要的反馈电阻值，使用10K继电器选择相应电阻实现增益。

The results indicate: 1 closed- loop gain and open-loop gain to meet basic relationship; 2 the stability of feedback is enhanced and output resistance increased. Furthermore, the result of open-loop and closed-loop gain of theoretical calculation is consistent with simulation which is applied by EWB software, which confirmed elementary conclusions and relationships in negative-feedback amplifier quantitatively.

结果表明：闭环增益与开环增益满足基本关系式；引入负反馈后稳定性得以提高，输出电阻增大；同时使用EWB对开环与闭环增益也进行了仿真分析，结果与理论计算一致，从而定量地验证了负反馈放大电路中的结论与关系。

In this paper, digital potentiometers X9C103 to change the high-frequency amplifier feedback resistor to achieve the control feedback purposes.

本文采用数字电位器X9C103来改变高频放大器的反馈电阻以达到控制反馈的目的。

Students have to study how to efficiently use the tools for performance measurement on basic circuits through observation.(3) The un-ideal performance of circuits such as frequency response and noise.(4) Feedback, Operational amplifier and the stability in feedback system.

通过观察对基本电路性能的量化建立有效的分析工具(3)频率响应和噪声等电路的非理想性的介绍(4)反馈，运放和反馈系统中的稳定性。

Whether an input or output impedance is raised or lowered by feedback depends on the type of amplifier to which feedback is applied, as will be shown in the next section.

通过反馈后输入或输出阻抗是升还是降，取决于所提供的反馈的放大器的类型。在下一节中，我们将讨论这个问题。

Negative feedback circuit is the main body of SAW drive circuit which is composed by operation amplifier and feedback network, its function is to realize output impedance matching and electric circuit stable gain.

负反馈放大器是该驱动电路的主要部分，它由运算放大器加上电阻和电容构成的反馈网络组成，其功能是实现输出阻抗匹配以及保证驱动电路增益的稳定性。

A method to reduce the nonlinear error of a bridge using operational amplifier feedback were introduced,the feedback conditions of canceling nonlinearity were found by circuit analyzing.

采用放大器反馈控制法克服了传感器电桥的非线性误差，通过解析的方法找到了克服非线性误差的放大器反馈控制条件。

So we designed a adaptive synchronizing controller based on hereinbefore hardware environment: first a small magnitude reference signal r is outputted to system through the signal card (to ensure that the vibrating system works in a linear state), and this signal is sent to the moving coil of vibrator through the power amplifier, so vibration is produced through electromagnetic induction. Secondly the vibration signal can feedback to the data acquiring card in the servo system through the acceleration sensor on the Vibroseis reactor M〓 and the base-plate M〓, then the computer can get the current vibrating state y〓 of the coil of vibrator according to the feedback information from the data acquiring card, and give a real time comparing between the current state y〓 and the reference output y〓 of the set-in reference model with current reference input being r , then regulates the correlative controlling parameters according to the error e〓=y〓-y〓 till y〓→y〓, finally normal signal sweeping begins with a certain phase fixed. Meanwhile a synchronization signal for seismic signal record is sent to seismograph from synchronization signal outputting component in the Vibroseis system to perform the controlling process of synchronization of sweeping phases.

为此，我们基于以上的硬件环境设计了一个自适应同步控制器：首先通过信号发生卡对系统输出小幅度的参考信号r(从而保证振动系统工作处于线性状态)，信号通过前置放大器、功率放大器等送到激震器动圈，并通过电磁感应产生振动，振动信号通过可控震源激震器反应块M〓和基板M〓上的加速度传感器反馈给伺服系统中的数据采集卡，工控计算机根据采集卡的反馈信息，获取当前激震器动圈的振动状态y〓，并实时地将该状态与内置的参考模型在当前参考输入r下的参考输出y〓进行辨识，再将两者输出误差e〓＝y〓-y〓对系统的有关控制参数进行调整，直至y〓→y〓，最后在经过某一固定的相位后，开始信号的正常扫描过程，与此同时，由可控震源系统的同步信号输出部件向地震仪送出一地震信号记录同步信号，进而完成扫描相位同步控制过程。

In this paper, the analytic expressions of closed-loop voltage amplification factor A(subscript vmf for the reversed feedback amplifier are derivated by circuit analysis, without using feedback coefficient.

用电路分析方法，不再使用反馈系数，导出4种负反馈放大器闭环电压放大倍数A的解析关系式。

There are proponents and opponents of negative feedback, regardless of its shortcomings, and Densen has chosen the design route of using no global feedback which is very difficult to do in a solid state push-pull amplifier.

有支持者和反对者的负反馈，不论其缺陷，电线选择了不使用全局反馈，这是很难在推动固态做推挽放大器的设计路线。

In the chapter 2, the theoretic knowledge about the photosensitive resin and the grinding tools was firstly introduced.

第二章阐述了光固化树脂结合剂磨具的相关理论研究。

Do not use the program's indenting or margin-setting features; these will be added during typesetting.

不要使用缩排，页面边缘设置之类的选项，偶看不大懂。