电流脉冲

The magnetization intensity and direction of AlNiCo PM can be controlled by pulses of d-axis stator current vector.

通过定子直轴电流矢量脉冲控制铝镍钴的磁化强弱和方向，使钕铁硼和铝镍钴产生的磁通共同穿过气隙；或者使钕铁硼产生的磁通部分穿过气隙、部分被铝镍钴在转子内部旁路，利用永磁体的记忆能力使永磁气隙主磁通受控。

This system can produce a negative pulse of current at any moment of the short circuit transfer.

该系统实现了在短路电流波形任意点上迭加一负脉冲电流波形。

This paper presented the research and exploration of mechanism and technics as well as the design of the magnetic circuit of this new compound machining, based on above, establishing the parameter model, meantime, analyzing influential effects on productivity of magnetic and EDM compound machining the holes through large numbers of experiments, including velcoity contrast experiments of pre-compound and after-compound machining with the change of current, velcoity contrast experiments of pre-compound and after-compound machining with the change of magnetic induction, velcoity contrast experiments of pre-compound and after-compound machining with the change of impulse width, experiments of the superficial roughness, experiments of the Electrode wastage, and intersectant experiments analysis as well as the change experiments of current waveforms. Through a number of experiments we analysed the influential effects of magnetic and EDM compound machining, compared the factors with EDM by oneself. A large of experiment records and deducibility have demonstrated that the productivity of magnetic and EDM compound machining is developed by 20%～400% than traditional EDM.

本论文对磁场电火花复合加工这种新的复合加工的机理、工艺和复合加工的磁路设计进行了研究和探索，在此基础上，建立了磁场电火花复合加工的参数模型，同时通过大量的随着电流变化磁场电火花复合前后加工速度对比实验、磁感应强度变化时的加工速度变化实验、随脉冲宽度变化的加工速度实验、表面粗糙度实验、电极损耗量实验、磁场电火花复合加工正交实验分析、电流波形变化等实验，实验分析了影响磁场电火花小孔加工效率的因素，并且跟单一的电火花加工中的影响因数进行了比较，大量的实验数据和理论推导证明磁场电火花复合加工比传统的单一电火花加工的效率提高了20％～400％左右。

After researches it was found that it takes place only in case of direct current or impulse current.

经过研究发现，它只是发生在案件直接电流或脉冲电流。

A quantitative analysis for dynamic stability of a set of superconducting partial torus in a fusion reactor under a pulse current over a stationary current is given.

对于聚变反应堆中超导载流磁体在稳态电流基础上受到脉冲电流影响时的动力稳定性给出了定量分析方法。

The contributions to the induced current and voltage by various electromagnetic field components, such as the vertical electrical field, the horizontal electrical field and the horizontal magnetic field, are compared in this paper in terms of integral of Green function and superposition theorem.

结果显示，Agrawal和Taylor模型得到的电压、电流响应是一致的，可以考虑在有界波电磁脉冲模拟器中进行短线缆的效应实验；由于相同的场分量在不同的模型中对电压、电流响应的贡献并不相同，因此在阐述某一场分量对线缆响应贡献大小时，应该首先说明所采用的传输线模型。

The square wave or corrected sine wave auto inverters have many limitations. When supplying to inductive load (such as electric fan, electric drill etc.), a square wave or corrected sine wave auto inverter produces too much harmonic current which makes the load seriously heated and even damaged. When supplying to capacitive load or rectificative load such as notebook PC, mobile phone charger etc.

方波或修正正弦波电源有很多局限性：在为感性负载供电时产生大量谐波电流，导致电器严重发热，甚至损坏；为容性或整流性负载（笔记本电脑、手机充电器等）供电时产生严重的脉冲电流，严重时可能导致电器损坏。

At 25℃,in 30w/o KOH aqueous,when current density is 2000A/m 2,the evolution oxygen overpotential of the oxidized Ni anode decreases 260mV relative to unoxidized Ni anode.

常温下，电流密度2000A／m2电解30％KOH水溶液时，脉冲电流氧化的Ni阳极析O2超电势比普通Ni阳极下降260mV。

And this paper introduced the principium, design ideal and approach of waveform presetting of waveform controlling at will The function of relevant hardware circuit controlling was design in this paper uses litter content RLC surge circuit in simulating the current signal of energy storage welding, and took it as Ug to control the inverter cap energy storage spot welding machine. It realized HFPEC resistance spot welding with hardware circuit and got the effect as good as the system controlled by industrial computer and realized the customization and the low cost of welding machine.

本文所设计的相应硬件控制功能，采用小容量RLC 放电回路来模拟输出储能焊过程的电流波形，由此作为电流给定信号直接控制逆变式电容储能点焊电源，实现了完全由硬件电路构成的高频脉冲电阻点焊，能够获得焊接设备的专用化和低成本化的结果，并且可以得到与工控机控制系统相当的焊接效果。

It centers mainly on the difference between pulse cyanide silver coating and DC cyanide coating in appearence, micromorphology and anti-sulphur ability.

用霍尔槽实验法初选了氰化物溶液中方波脉冲镀银的工艺参数范围，进而用组合实验确定出了最佳的脉冲周期、占空比和平均电流密度。

I'm strongly against the death penalty — it's an eye for an eye.

我不赞成死刑——这是以牙还牙的报复行为。

And to get you the support you need, we're enlisting all elements of our national power: our diplomacy and development, our economic might and our moral suasion, so that you and the rest of our military do not bear the burden of our security alone.

并给你们所须的支援，我们正徵召国家所有各种的力量：我们的外交及发展，我们的经济力量与道德劝说，所以你们与其他军人不须要孤独地负起国家安全的责任。