查询词典 statical friction

The substitution of rolling friction for sliding friction results in a very considerable reduction in friction.

用滚动摩擦代替滑动摩擦，结果使摩擦大大减少。

Aiming at the friction problem of metal deformation in stretch reducing course, a friction model has been established to solve the contact friction problem in rolling course simulation accurately.

针对张力减径过程中金属变形的摩擦问题，建立了摩擦模型，比较准确地解决了轧制过程仿真时的接触摩擦问题。

Main innovation and study achievements are described as follows:(1) A set of friction noise testing system was set up on the pin-on tester. In the process of friction testing in which the TRIP steel with transformation characteristics is continuously sliding in unilateralism, variety rule of the friction noise intensity was studied.

本文的主要创新和研究成果体现在以下方面：(1)在销盘摩擦磨损试验机上建立了一套摩擦噪声测试系统，研究了具有相变特征的TRIP钢在单向连续滑动的摩擦试验过程中，摩擦噪声的强度的变化规律。

Main job is to guarantee the scraping interaction and equipment on both sides of the friction surface or can obtain higher precision and accuracy, precision and shape accuracy, precision and contact transmission because of good lubrication, manual and repeatedly is worthy, large amounts of wind, time-consuming, scraping the time needed for different devices vary, such as boring slider and slide block wind profiling, between the match before measuring clearance between the original value, and then according to the technical requirement to measure the value of time and scraping scraping, then apply DanFen red on the slider, manual let slip on the slide seat back and forth, they do straight-line movement between full contact and friction, reoccupy scraper scraping friction creates the contact point, so repeatedly, until the technical requirements for the match, single within 2 days, must blow to the boring if all the time to work with wind, a half month is required.

刮削过程。刮削工作主要是为了保证设备相互接触并摩擦的两面间能获得较高的尺寸精度、形状精度、位置精度、接触精度、传动精度和良好的润滑，因是手工操作且需反复配刮，故工作量大，耗时较长，设备不同，刮削所需时间也各不相同，例如镗床上滑座与下滑座间的配刮，刮削前先测量出二者之间原有的间隙值，然后根据工艺要求测算出需刮削值及每次的刮削量，再将红丹粉涂于上滑座之上，手工让上滑座在下滑座上来回做直线运动，使它们之间充分接触和摩擦，再用刮刀刮削摩擦产生出的接触点，如此反复多次，直至技术要求范围之内，单此项配刮需2天左右，若对于整个镗床所有配刮工作的时间总和，则需半个月左右。

In the course of FEM model building, tensile test experiment is taken to work out the real stress-strain curve. Ring compress test is also done in this paper, through which the friction coefficient is worked out and the friction mechanism and relevant friction model for tube stagger spinning is studied. The experiments ensured the veracity and reliability of the FEM modeling.

建模过程中，通过材料拉伸试验测定了旋压材料00Ni12Cr5Mo4TiAlV时效钢的真实应力应变曲线；利用圆环镦粗试验测定了材料在不同润滑状态下的摩擦系数，并对强力旋压的摩擦性质和摩擦模型的选择进行了研究，确保了建模关键参数的准确性和可靠性。

In the paper, the friction coefficient of the friction pairs of Al2O3 matrix ceramic/45# steel during sliding experiments were studied, and the worn trace's micrographs of Al2O3 matrix ceramic were observed and analyzed, and the wear mechanism of Al2O3 matrix ceramic in dry friction and oil Iubrication were analyzed.

摘 要：本文对Al2O3基陶瓷材料/45#钢摩擦副的摩擦系数与45#钢/45#钢的摩擦系数作了对比滑动摩擦试验研究，观测分析了Al2O3基陶瓷材料磨痕形貌，并就干摩擦，油润滑状态下Al2O3基陶瓷材料的磨损机理进行了分析。

At the aspect of the fade and the average wear, the bakelite modified by the chemigum was better than the bakelite modified by the bunas; When mixing the kevlar fiber and steel fiber their"cooperation effect"happened easily, especially, in the proportion of one to four, the friction materials had the better tribology performance; It was demonstrated that Sb2S3 played a role of binding adhesive of friction materials in high temperature, which could reduce the content of the agglomerant, but it was a higher price material, mixing the petroleum powder and CuS in appropriate proportion would replace it in friction

应用造粒技术，采用颗粒包层的方法，改变摩擦材料内部结构，使摩擦材料由配方比例设计到配方与结构综合设计的转变成为可能，将为研制新型摩擦材料探索出一条新的思路。

AlTiN coating has inconspicuous anti-wear effect on carbide.(3) With the introduce of graphite chips bwteen the frictional surface, the effect of graphite chip on the sliding friction and wear behavior of frictional pair was studied. The results show that graphite chips can reduce the coefficient of friction and frictional temperature, and make the coefficient of friction decrease with the decrease of normal load and rise of sliding speed.

在硬质合金微铣刀高速铣削石墨的刀具磨损和破损研究方面，分析了石墨高速铣削过程中的摩擦学条件，揭示了涂层和非涂层硬质合金微铣刀高速铣削石墨的刀具磨损和破损形态及其机理，研究结果表明涂层早期剥落是涂层的早期破损形式，&抛光&磨粒磨损是涂层硬质合金微铣刀在稳定磨损期的主要磨损机理。

The results showed that under the given experimental conditions,the surface layer with richiron and poor copper was formed in the surface worn region of the semimetallic friction material,the depth of organic ingredient pyrolysis caused by friction heat in worn surfaces was atout 0.35mm; the semimetallic friction material containing 15%-20%of Cu had better wear-resistance,and can form a even and continuous transfer film of copper; crack peeling was the importantmechanism of the counterpart.

半金属摩擦材料具有摩擦系数稳定，耐磨性好，对环境污染小和对偶件表面损伤小等优点，但其在摩擦热和界面应力等因素作用下，表层会发生弹性变形，塑性变形，元素扩散，组分转移和摩擦化学反应等现象，因此，利用扫描电子显微镜X射线能量色散谱和差热－热重分析，对铜纤维增强的半金属摩擦材料与灰铸铁滑动摩擦表面层的特性作了分析研究，考察了表面层特性对摩擦损行为的影响。

Under heavy load and high temperature conditions, the nanoparticles are flatted between two friction surfaces and form a sliding system which makes the friction surface more flat to reduce the friction factor and the wear value.

在重载和高温条件下，纳米粒子平铺在摩擦面之间形成滑动摩擦层，以降低摩擦表面的摩擦因数和磨斑直径。

If you were not , and OS X just booted normally, have no fear.

如果你没有，和OS X刚刚启动通常，没有恐惧。

I only want to preserve our all .

我只想保存好我们的一切