查询词典 shear

It is found that two shear modulus are different and two shear strength are almost equal. The reason of differences between three point bending modulus and four point bending modulus is also analyzed.

在剪切试验中发现两种剪切试验的剪切模量相差较大，但由于两种剪切的破坏面相同，所以剪切强度相差不大。

Our company main products has: IC integer machine; IC legs cut machine; IC grinding machine word; electromagnetic machine parts; pneumatic machine parts; automatic bulk shear pin capacitance; belt loaded shear pin capacitance machine; belt fitted Capacitor Forming Machine; in bulk, with mounted machine resistance; None jumper waste molding machine; triode automatic molding machine; PC board feet cut plane; tungsten steel Grinding; bulk with loaded machine parts; V-CUT substrate folding board machine; PC board sub-board machine; automatic feed plate; hand solder immersion heaters; PCB trolley, trolley and block tin, the ordinary solder kit aircraft series Reflow Products ....

本公司主要产品有：I.C整型机；I.C切脚机；I.C磨字机；电磁式零件成型机；气动式零件成型机；全自动散装电容剪脚；带装电容切脚机；带装电容成型机；散装、带装电阻成型机；无废料跳线成型机；三极管自动成型机；PC板切脚机；钨钢刀磨刀机；散装、带装零件成型机；V-CUT基板折板机；PC板分板机；自动送料盘；手浸式焊锡炉；P.C.B台车、手推车及挡锡条、金手指防焊套、流焊架等系列产品。。。。

Main Product: resistors forming shear pin machine, shear pin capacitance molding machine, molding machine crystal, V-CUT substrate sub-board machine, Grinding, cutting foot machine, pneumatic molding machine, IC plastic plane, IC legs cut machine, IC grinding the word machine, automatic feeding plate, tungsten steel chip, PCB solder placed Units cars and exclusive framework, block tin, the ordinary solder Series Des Welding Products

主要产品：电阻成型切脚机、电容成型切脚机、晶体成型加工机、V-CUT基板分板机、磨刀机、切脚机、气动成型机、IC整型机、IC切脚机、IC磨字机、自动送料盘、钨钢刀片，PCB放置台车及焊锡专用框架、挡锡条、金手指防焊系列辅焊产品

In this paper, we review relationship of bulk and shear modulus and apply the Gassmann's equation to predict shear modulus.

本文对体变模量和剪切模量之间的关系进行讨论，并使用Gassmann方程来预测剪切模量。

At low shear rate, the beood of human body perform as Casson fluid, but at high shear rate incline toward Newtonian fluid.

在低剪变率条件下人体血液表现为卡森流体，在高剪变率条件下则趋向于牛顿流体。

However, the Casson equation agrees well only when the shear rate is less than 10 s?1. The flow field of the carotid bifurcation usually covers a wide range of shear rate. We therefore believe that it may not be sufficient to describe the property of blood only using the Casson equation in the whole flow field of the carotid bifurcation.

然而Casson模型只有在低切变率条件下才与血液吻合的较好，而在颈动脉分岔血管中切变率值的分布范围却很广，因此，我们有理由认为，在整个颈动脉分岔血管流场中均采用Casson模型来模拟血液的本构关系是不够的。

It is shown that the mechanical properties including Young's modulus, tensile strength, critical strain and stress under buckling can be enhanced with the decreasing of intershell spacing. The shear strength can be enhanced by 2-3 orders of magnitude when the intershell spacing is reduced to 20%, which is also dependent on commensuration. Zigzag-type carbon nanotubes have higher shear strength. The axial stress in tubes when the load transferring from outmost tube to inner tube is observed as well.

研究了单壁纳米管束横截面的六方化失稳现象，给出各种管径的面内压力－应变关系曲线；每条曲线都给出一个明显的拐点而且有很强的非线性；线弹性模量与参考构形有关，也受管直径的影响；分析了管束横截面的晶格不稳定性特征，表明晶格的缺陷能够明显的减小临界值；模拟了在不同应变下纳米管束对静水压的反应，发现不同压力下的截面形态不同，在很高压力下相邻管之间会形成化学键。

Through referring related documents and analysis of builded bridges home and abroad, this dissertation makes anslysis on design of whole bridge on the basis of design theory for general box-girder, and combined with the design of Long-March bridge. There makes a special research on shear connecter which connecte corrugated steel webs with concrete board up and down. Design method of shear connecter is discussed.

本文在参阅国内外有关文献及实桥资料的分析，以普通混凝土箱形梁设计理论为基础，结合长征桥的设计，分析了整个桥梁的设计过程，尤其对波形钢腹板和顶底板混凝土的剪力连接件进行了研究，给出了计算方法。

The critical Reynolds number decreases with countercurrent shear stress and increases with cocurrent shear stress.

切应力对表面波的稳定性作用与气流方向和液膜的流动状态相关。

A theoretical model for calculating the cutting angle with different crystal planes, orientations and tool orthogonal rakes are described in this paper. It is built with the ultra-precision cutting model by the principle of the maximum specific energy of shear deformation and the mechanism of change of the shear modulus with...

本文利用剪切变形比能最大及单晶材料不同晶面晶向剪切弹性模量不同的原理，结合超精密切削模型，从理论上计算出不同晶面、不同晶向及不同刀具前角超精密切削条件下的剪切角，得到其在不同切削条件下的变化规律，并由此解释了切削加工中由KDP晶体各向异性所导致的工件表面粗糙度的各向异性。

I want to be a big fish in a small pond.

我要做一条在小池塘里的大鱼。

While the software functioned well, we did not feel the same about their customer support!

虽然该软件运行良好，我们没有同样的感觉他们的客户支持！