查询词典 shear angle

For some conventional materials, the shear deformation can be neglected because of the higher shear modulus.

由于更高的剪模数，为一些常规材料，剪变形可以被忽略。

The internal codes of RC were still constituted by the source of ACI system.at present. This detection could be found when treat the destruct mode of RC. Failure mode of bending behavior have the tractility to be a warning for hold off. Whereas shear would often fracture in a second and make big toll. Accordingly, avoid the shear failure happening which had been an important subject of structural design.

中文摘要目前国内对RC规范的订定仍以ACI 规范系统为主要依据，而探讨RC结构的破坏模式时可以发现，挠曲的破坏行为富有延展性，具有延迟预警的效果，反之剪力的破坏则常发生於顷刻之间，往往造成重大伤亡产生，因此避免剪力破坏的发生在结构设计上仍是项重要的课题。

The device as set forth in claim 1, wherein the at least one hinge fitting includes a plurality of shear pin slots configured to receive corresponding shear pins.

该装置所规定的索赔1 ，其中至少有一个铰链配件包括一个多元化的剪切针插槽配置得到相应的剪切销。

Process: line: All incoming plug welding of plastic classification shear shear pin machine repairing washing feet.

工艺流程：直插：来料合对整形分类插件焊接切脚机切脚补焊清洗。

These results is helpful to the institution of fired perforated brick masonry code of Chong Qing. And it is benefit to the popularization of perforated brick. Analysis of experimental result has show 4 points below.① Shear strength of perforated brick masonry is composed of mortar cohesive strength and pin keys shear strength.

试验结果分析表明：①多孔砖砌体的抗剪能力由砂浆粘结抗剪和砂浆销键抗剪两部分组成，由于砂浆销键的存在，多孔砖砌体的通缝抗剪强度较实心砖砌体有较大幅度的提高。

It is found that there is a particle migration towards lower shear-rate regions on the shear plane, which does not exist on the vorticity plane.

发现球体对在剪切面有向低剪切率方向漂移的运动，而在涡旋面这种漂移运动并不存在。

The results show that the frictions caused by the wall of shear box will influence the distributions of stresses in specimens and the normal pressure stresses on the shear plane.

结果表明，剪力盒壁摩擦力将会影响试验土样中的应力分布和剪切面上的正压应力值。

Two similar properties are compressive strength and shear strength, related to compressive forces and shear forces respectively.

两个类似的性能分别是与压缩力和剪切力有关的压缩强度和剪切强度。

The shear stress of particles is about 5% of the turbulent shear stress of the water.

颗粒剪切应力的数值约为水流紊动剪切应力的5％。

The shear stress and apparent viscosity of the masterbatch decreased with the increase of the shear rate and temperature.

随着剪切速率的增加，温度升高，剪切应力会降低，母粒的表观黏度也随之降低。

It has to be computed by the host for the actual clock rate.

主控制器可以用来计算实际的时钟速率。

Let's see what you got.

让我看看你的东西