查询词典 process industries

Comparing with conventional air handling process, the liquid desiccant air-conditioning system can dehumidify air without cooling down to its dew point. Meanwhile, counteraction cooling and heating can be avoided, which usually happened in conventional air handling process and led to huge energy waste. In addition, during the air handling process no condensation water separates out of the air in the liquid desiccant air-conditioning system, thus, avoid fungi thrives in moist environment of traditional air handling process. Not only being applied in dehumidification process in summer, the system can also realize humidification process in winter conditions efficiently.

与传统的空气处理方式相比，采用溶液式空气处理方式，具有如下优越性：取消了冷凝水表面，消除了霉菌等生长所需的潮湿环境；既可以对空气除湿处理，又能实现冬季对于空气的加湿处理过程；可方便调节处理后的相对湿度，不再是常规冷凝除湿方式中接近100%相对湿度的出口空气参数；避免了常规空调系统冷凝除湿后温度过低还需再热带来的冷热抵消问题；可以充分利用低品位能源如太阳能和废热实现溶液再生，节省系统电耗。

In the dehydrogenation process of HD process, the temperature set at 580℃ and pressure set at 100Pa is a perfect parameter, it can make the magnet to have high magnetic performance. In the HDDR process experiment, the paper contrast four HDDR process such as C-HDDR V-HDDR V-HD-S-DR and d-HDDR by the anisotropy and magnetic performance of ternary NdFeB magnetic material. The results show that adjusting the parameter of the d-HDDR process can make the anisotropy and magnetic performance of ternary NdFeB magnetic powders to catch up with the hexahydric NdFeBCoZrGa magnetic powders. At the end the paper discusses the betterment of the equipment which produces ternary NdFeB magnetic with the d-HDDR process.

和580℃的脱氢温度相搭配的脱氢气压选择在100Pa左右是理想的工艺参数，这样的搭配使得最终烧结磁体综合磁性能优异；在HDDR制粉工艺实验中，本文对比了C-HDDR、V-HDDR、V-HD-S-DR和d-HDDR四种HDDR工艺对于三元NdFeB合金各向异性和磁性能的影响，得出结论：通过发展d-HDDR工艺，调整工艺参数和控制水平，可以使三元NdFeB合金磁粉的性能达到或接近六元NdFeBCoZrGa合金磁粉的水平，在文章末尾，还对配合使用d-HDDR工艺设备的改造进行了分析。

During the intermissive fed-batch process, the feeding medium was added 10 times separately to make the total amount of C and N sources equal to those added in the batch process, and the yield of maduramicin was improved to 9645 μgmL^(-1), which is 15.7% higher than that obtained during the batch process. In the continuous fed-batch process, the maduramicin yield reaches 10328 μgmL^(-1), which is 6.0% higher than that obtained in the intermissive fed-batch process, and is 29.4% higher than that obtained in the batch process.

在间歇补料分批发酵工艺中，分10次补加培养基，使碳、氮源的总浓度与分批发酵相同，马杜霉素发酵单位提高到9645μgmL^(-1)，比分批发酵提高了15.7%；在连续补料分批发酵工艺中，马杜霉素发酵单位可达10328μgmL^(-1)，比间歇补料分批发酵提高了6.0%，比分批发酵提高了29.4%。

The results showed high class PbSt2 could be synthesized by this new saponifying process.Compared with metathetical process,the reaction time shortened,liquid-solid ratio and moisture content of filter cake decreased.Powder product could be prepared by one-step process,and particle product by two-step process.For the optimum processing conditions,the reaction temperature and time for one-step process were 65℃ and 10min,the amount of alkali added in the first step was 50%;reaction temperture and time were 65℃ and 10min for the two-step process.

结果表明，用皂化法工艺可得到优等品PbSt2，较复分解工艺，反应时间缩短、液-固比降低、滤饼湿含量比减小，一步式工艺得到粉状产品，二步式工艺得到颗粒状产品；最佳工艺条件为：一步式工艺反应温度65℃，反应时间10min；二步式工艺第一步的加碱量比50%，反应温度65℃，反应时间10min。

In this paper, two assemblies of special test equipments have been designed and fabricated by authors in our laboratory: namely Catalyst Molding Process Analyzer and Catalyst Mechanical Process Tester. These new skills are developed for the dynamic studies on whole mold forming process and crushing process of Fe-Cr WGHS catalyst pellet. Based on the orthogonal experimental design, the effects of some factors during the forming process of solid catalyst, such as predensification proportion, calcination time, calcination temperature and content of graphite on the mechanical strength of catalyst pellets are systematically examined, and the molding conditions have been optimized. Based on the experimental data, the relationship between catalyst density and forming pressure are educed, and the physical significances of some related parameters are described. The parameter of macro scopic elastic moduls has been suggested to character the mechanical properties of molding catalyst. The effects of molding pressure on mechanical properties of catalyst pellets are discussed, and results show that there exists a optimal molding pressure for the ideal mechanical properties: when over-high or over-low pressure is applied, the specific surface area and side crushing strength of catalyst pellets will decreased. The "rebound effect" will be undermined by the unsuitable pressure maintain process, resulting in the apparent decrease of mechanical strength of catalyst pellets.

本研究通过自行设计制造的催化剂模压成型过程分析仪（Catalyst Molding Process Analyzer， CMPA）和催化剂力学性质测试仪（Catalyst Mechanical Properties Tester， CMPT），以Fe-Cr系高温变换催化剂片剂为研究对象，对成型过程和受压破碎过程提供了全过程动态研究的新手段；本研究利用正交实验设计方法考察了固体催化剂成型过程中诸因素（包含预密致比例、煅烧时间、煅烧温度和石墨含量等）对催化剂成型体强度的影响，并对成型条件进行了优化；根据实验结果，关联确定了固体催化剂成型过程中的密度－压力关系式，并对方程中诸因子的物理意义进行了描述；提出了一种利用宏观弹性模量来表征成型催化剂的力学性质的方法；研究讨论了成型压力对催化剂成型体强度性质的影响，结果表明：对于催化剂成型体的强度和比表面性质，成型压力存在着一个最佳值，过高的成型压力会导致比表面积和侧压强度的降低；不适当的成型压力的维持时间会破坏&压力回弹&作用，造成催化剂成型体的机械强度明显降低。

A integrated mathematical model was established in accordance with the process of metallurgical production and it was composed of the process models and the raw materials distribution models. The process models include the sintering process model, the pelleting process model and the iron making process model.

数学模型分为6个子模型，其中工艺模型有烧结机优化模型、竖炉优化模型、高炉优化模型，物料配置模型有铁精粉优化配置模型，烧结矿优化配置模型和球团矿优化配置模型，模型之间交互的数据流为原料或产品的物料流量、物料性能、价格及原料性能的影子价格。

It is useful to reduce the occurance of acid mist by adding erosion retardant and surface activity into acid which has been used in some industries.in the developed province and city, the bureau for enviroment protection calls on all enterprises to process the heated zincification water and prohibit from drainage, all enterprises should process the rinsed waste water and plating-aid waste water,however it remains to be strengthened across the country for the process of three wastes come from heated zincification

在酸中添加缓蚀剂和表面活性剂可以减少酸雾的产生，已在一部分企业中得到应用。在发达省市，环保部门要求企业必须对热镀锌废水进行治理，不得外排，企业对漂洗废水、助镀废液均进行处理，但全国范围内对热镀锌的三废治理还需加强。

Using the proposed identification and control strategy, the identification results of two kinds of systems and the simulation of a bilinear process control system are presented. The generality of the model and the simplification of identification and control method together with the simulation results show that the above strategy has strong possibility to nonlinear system and high order system identification for process industries and the excellent control performances superior to a standard PID controller for the same process.

用该方法进行了两个非线性系统的模型辨识和一个双线性系统的控制仿真，模型的通用性、辨识和控制方法的简单易用和仿真结果表明，所提出的方案对过程工业和非线性、高阶系统有很好的实用性，有着比标准PID控制器好得多的控制效果。

Using the method of qualitative research, operating the intention of process/stage theory,our research based on the theory of process of organizational innovation constructed by Amabile. In order to built the process/stage model of organizational innovation, with the methods of post hoc research, in-depth interview, triangulation and multi-analysis for the core cultural /creative industry of Taiwan, to realize the passing way of thinking and running model of organizational innovation of cultural/creative industry to find out the significant factors which affected the organizational innovation of cultural/creative industries.

本研究采用质性研究方法，运用阶段/历程之研究取向，并以Amabile的「组织创新历程模式」为理论基础，针对台湾核心文化创意产业做多重个案分析，并以事后回溯研究、深入访谈、及三角测量等方法，分析并建构其组织创新之阶段与历程模式，藉以了解文化创意产业组织创新所经过之思虑模式与作为方法，以及找出影响文化创意产业组织创新历程之重要因素。

Numerical simulation and optimization of process parameters in fineblanking process;2. As fineblanking 's wide application in different industries, such as auto mobile, aircraft and general mechanicals, the finite element analysis of fineblanking is playing a more and more important role in the process from design to manufacture.

随着精冲技术在汽车制造、航空器制造、通用机械等领域越来越广泛的应用，针对精冲过程的有限元数值模拟也越来越成为目前精冲应用领域从设计到制造的重要环节，而网格剖分是精冲成形有限元分析的关键技术之一。

We stopped by the old fashion ice cream parlor Manhattan Beach Creamery for some refreshment. The "No Shoes, No Shirt, No Problem" sign on the wall epitomizes the beach lifestyle.

我们去商店区的一家老式冰淇淋店坐坐，墙上挂著「没鞋，没上衣，没问题」的牌子完全捕捉了海滩生活的随性及风格。

"If therefore", argues Bellarmine we can offer our prayers and our satisfactions in behalf of those detained in purgatory, because we are members of the great body of Christ, why may not the Vicar of Christ apply to the same souls the superabundant satisfaction of Christ and his saints--of which he is the dispenser?

" "因此，如果"，认为贝拉明（德indulgentiis ，十四）"我们可以提供我们的祈祷和我们满意的代表那些被拘留在炼狱，因为我们是成员的伟大基督的奥体，为什麼可能不是牧师基督适用於同样的灵魂满意的过剩是耶稣和他的圣人-他是在配药？