查询词典 impression drawing

Closed has carried on the reasonable determination highly to the mold, but also designs the mold the major parts to fall the material concave mold, the convex-concave mold, the counter- drawing raised mold, the counter- drawing concave mold, the concave mold dead plate and so on.

对模具的闭合高度进行了合理的确定，还设计出模具的主要零件落料凹模、凸凹模、反拉深凸模、反拉深凹模、凹模固定板等。

In this design introduced the transmission covers the punch holes the ramming craft analysis, the craft plan formulation, arranges the specimen map design, the always ramming strength computation and the center of pressure computation, the cutting edge size computation, the spring, the rubber computation and selects, the raised mold, the concave mold or the convex-concave mold structural design and all that die the components structural design, draws up the mold assembly drawing and the work detail drawing, the compilation design instruction booklet, fills in the ramming craft card and the work components machine-finishing technological process card, raised pays attention to, the concave mold coordinate processing.

本设计中介绍了传动盖冲孔的冲压工艺分析，工艺方案的分析和制定，排样图的设计，总的冲压力计算及压力中心的计算，刃口尺寸的计算，弹簧的计算和选用，凸模、凹模或凸凹模结构设计以及其他冲模零件的结构设计，绘制模具装配图和工作零件图，编写设计说明书，填写冲压工艺卡和工作零件机械加工工艺过程卡，注意凸、凹模的配合加工。

In this design introduced the transmission covers the punch holes the ramming craft analysis, the craft plan formulation, arranges the specimen map design, the always ramming strength computation and the center of pressure computation, the cutting edge size computation, the spring, the rubber computation and selects, the raised mold, the concave mold or the convex-concave mold structural design and all that die the components structural design, draws up the mold assembly drawing and the work detail drawing, the compilation design instruction booklet, fills in the ramming craft card and the work components machine-finishing technological process card, raised pays attention to, the concave mold coordinate processing.

摘要本设计中介绍了传动盖冲孔的冲压工艺分析，工艺方案的分析和制定，排样图的设计，总的冲压力计算及压力中心的计算，刃口尺寸的计算，弹簧的计算和选用，凸模、凹模或凸凹模结构设计以及其他冲模零件的结构设计，绘制模具装配图和工作零件图，编写设计说明书，填写冲压工艺卡和工作零件机械加工工艺过程卡，注意凸、凹模的配合加工。

Dolley hosted official engagements as well as weekly "drawing rooms" for the public, drawing a true cross section of society to the White House. This made her very popular with the American people.

多莉不仅时常设宴待客，还每周定期邀请社会大众到白宫，让社会各个阶层的真实角色都能出现在白宫之内，这种作法让他相当受到美国民众的欢迎。

According to the velocity filed mentioned above, the contour of the drawing die was rationally designed. To prove its applicability and superiority, FEM software, MARC and SUPERFORM, were used to simulate the drawing process of cross tube in "conical die" and "streamlined die".

本文以十字形钢管为研究对象，开展对异型钢管拉拔成形过程研究，首先结合挤压流线理论，设计了&流线型&拉拔速度场模型，这为改善金属流动状态、降低能耗创造了良好条件；紧接着以&流线型&速度场为理论依据，对十字形管拉拔模具的凹模轮廓进行了合理设计。

Equipment feature: horizontal single-rank a section drawing wire, each group drawing wheel can be through a group eye-mould and cross wire convenient.

设备特点：卧式单列一段式拉线，每组拉线轮只通过一组眼模，穿线操作方便。

After analyzing a large number of typical deep-drawing process design plans, process design knowledge of deep-drawing process is summarized.

在分析了大量的典型拉深件成形工艺方案的基础上总结了拉深件工艺设计知识，并将它们按照冲压件工艺设计过程进行模决化组织。

Both the limit deep-drawing coefficients and the lowest deep-drawing coefficients should be determined with both wrinkle and fracture limits.

极限拉深系数和最小拉深系数应由皱曲和破裂两极限来确定。

By analyzing the structure of process knowledge in deep drawing, a new featurebased hierarchical object model of knowledge for deep-drawing process is proposed, which constructs the knowledge base well, and so enables the mapping from forming feature to knowledge base.

通过对拉深工艺知识的结构分析，提出了基于特征的拉深工艺知识的层次对象模型，解决了工艺知识库中知识结构的编排和知识存储、管理，使得由成形特征向知识库的映射成为可能。

According to design route of the forming process of drawing with camber die, this software can be divided into 3 modules: the module of the chamber design, the module of process parameters design, the relative diagram of influence factor of limit drawing coefficient.

按照曲面凹模拉深成形工艺的设计路线，软件设计成三个功能模块：曲面凹模型腔设计模块、工艺参数设计模块、极限拉深系数影响因素关系图。

I hope that this success is just the first in a long series.

我希望这只是成功的开始。

Three dimensional stresses on the interface of tire and soil, tire deflection and soil sinkage are measured.

测试轮胎——沙土界面上的三向应力、轮胎变形和沙土沉陷；建立考虑剪切应力对沙土承载特性产生影响的车轮牵引性能预测模型；分析车轮作用下土壤的纵向稳定性。