查询词典 diameter

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skilled welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skil led welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

The results indicate that the cooling rate of melt droplet that can not break further depends not only on its diameter, but also on its position in atomizing chamber. As a result, the same sized particles in different positions show different cooling rates and two different kinds of microstructures. The cooling rates of melt droplets range from 104 to 108 K/s, and the critical cooling rate for glass formation of Al-Ni-Y is about 105 K/s. Moreover, the corresponding maximum diameter of amorphous particles is 25 μm, which accords well to the theoretical analysis results. The new approach, reflecting the complexity of close-coupled gas atomization objectively, is available and effective to evaluate the cooling behaviors of close-coupled gas atomization.

结果表明：在一定的工艺条件下，紧耦合气雾化存在多种破碎模式，熔滴的冷却速率因直径、雾化位置的差异，相同直径熔滴经历结晶和非晶化2种不同冷却行为；依据Al基合金粉末的粒度分布和微观结构，结合熔体的雾化过程及冷却模式，确定熔滴冷却速率的上、下限；实验得出熔滴的冷却速率为104~108 K/s，Al-Ni-Y合金的非晶化临界冷却速率为105 K/s，能形成非晶态的熔滴最大直径为25 μm左右，实验结果与理论分析结果较吻合，比较客观地反映紧耦合气雾化的复杂过程。

The company's automation and control products in the CX system of centralized control shaft are Jiantong Nanjing Cement JT energy saving and environmental protection-type large-diameter shaft (§3.8x8.5 meters,§4.0x8.5 meter shaft) fixed-point matching products applies to Nanjing Jiantong Guantang Ltd., Guangxi Pingguo Wanganui Cement Co., Ltd. all JT energy saving and environmental protection-type on large-diameter shaft; the company independently developed CX-JM15C coal environmental protection agents, dedicated to catalytic coal cement shaft kiln calcined, and its coal effect and Kiln Burning can improve working conditions, improve clinker production quality, reduce cost of production of clinker 3-5 yuan / ton clinker; company also provides enhanced FGF efficient composite cement grinding aids, Products has two kinds of solid and liquid, has good strength and grinding role.

公司的自动化控制系列产品中的CX立窑集中控制系统是南京建通水泥公司JT节能环保型大直径立窑（Ф3.8x8.5米，Ф4.0x8.5米立窑）的定点配套产品，应用于南京建通官塘有限公司、广西平果万佳水泥有限公司等所有JT节能环保型大直径立窑上；公司自主开发的CX-JM15C环保节煤剂，专用于水泥立窑催化节煤煅烧，其节煤效果明显，并能改善立窑煅烧工况，提高熟料产质量，降低熟料生产成本3-5元/吨熟料；公司还提供FGF高效复合水泥增强助磨剂，产品有固体和液体两种，具有良好的增强和助磨作用。

The main jobs and results show that:With the mechanical knowledge and technical condition,affords the mathematical modules about the roller diameter value range,the roller wheelbase value range and the axis neck diameter value range of coil box,and gives the method of experiential values .

本文从事的主要工作如下：利用力学知识和工艺条件，提出了确定热卷箱弯曲辊辊身直径、弯曲辊辊距、弯曲辊辊颈直径取值范围的数学模型，并给出了经验取值的方法。

The number of fruits had the highest directly positive relationship with seed yield,followed by leaf length,collar diameter,length of bearing branch,hundred-seed weight,the number of branches,angle of bearing branches,the height of bearing branches and plant height;five of 14 seed yield components exhibited directly negative relationships with seed yield,including leaf width,ratio of leaf length to width,the number of bearing branches,bottom diameter of bearing branches and ratio of bearing branches to branches.

2果实数对种子产量的直接正效应最大，其后依次是叶长、地径、结果枝长、百粒重、分枝数、结果枝角度、结果枝高度和株高；14个产量因子中有5个对产量有直接的负效应，包括叶宽、叶长宽比、结果枝数、结果枝底径和结果枝比。

You can use grips to specify compression spring diameter or wire diameter.

您可以使用掣点来指定压缩弹簧直径或线材直径。

The hydraulic loss of conduit in both vertical pump system and bulb tubular pump system were calculated using the numerical simulation, and the influence of pump impeller diameter on hydraulic loss of conduit was analyzed. Based on the similitude rules of impeller pump, the relationship between pump impeller diameter and nD value and the influence of pump selection and design were analyzed.

采用数值计算的方法，分别计算了具有不同水泵叶轮直径的立式轴流泵装置和灯泡贯流泵装置的流道水力损失，比较了水泵叶轮直径对流道水力损失的影响；根据叶片泵的相似律，分析了在一定设计流量条件下水泵叶轮直径与nD值的关系以及对水泵选型设计的影响。

It is could be concluded that the larger pump impeller diameter may obviously increase the efficiency of both conduit and pump system; increasing pump diameter and decreasing its rotational speed is consistent with reducing nD value.It is suitable to pump system with low head to choose lower nD value, so as a hydraulic model of axial flow pump with the better hydraulic characteristics could be obtained.

结果表明：选取较大的水泵叶轮直径将显著提高流道效率和泵装置效率；&增径降速&与降低nD值是一致的；在泵装置扬程较低的情况下，选取较小的nD值便于选用到水力性能较好的轴流泵水力模型。

Stainless steel shapes representative of the project has:surface Kaihua span 15-23 m cross-bridge Street Lightbox ads landscaping works; YRDP Command 7.3 meters long seamless stainless steel sheeté; Golden Port Hotel International Conference Hall in diameter 9.2 meters of aluminum alloy and the large modelinghotel all kinds of stainless steel shapes; more than 3 meters in diameter stainless steel ball production 8K; Sunshine Hotel, the external walls of stainless steel shapes; Provincial Agricultural Development Bank and other cultural wall.

不锈钢造型的代表工程有：开化寺街面跨度15米至23米桥式跨街灯箱广告美化工程；引黄工程指挥部7.3米不锈钢薄板无接缝超长挑檐；金港大酒店国际会议厅直径9.2米的铝合金特大造型灯盘及该酒店各类不锈钢造型；直径3米以上不锈钢8K钢球的制作；阳光大酒店的外墙不锈钢造型；省农发行的文化墙等。

There are different types of personal loans available.

有许多不同类型的个人贷款优惠。

The above mentioned teaching model of spiral rising can be used to avoid rigidness in teaching.

上述螺旋式上升的教学模式，可以避免教学形成模式後的僵化现象。