查询词典 compression member

The procedure is based on the concept that the critical load of a frame without sidesway is the same as the smallest value among these critical loads of the compression members of the frame with partially restrained ends, and the critical load of every compression member may be determined by the method of successive approximation.

将组成刚架的各桿件视为两端受不同约束的桿件，用静力学的方法求出此等桿件相应的临界荷重，其中最小值即为刚架的临界荷重，举有实例以示演算程序。

D1.1 of the AISI Specification limits the maximum longitudinal spacing of connections to ... where smax = maximum permissible longitudinal spacing of connectors L= unbraced length of compression member rI = radius of gyration of I-section about the axis perpendicular to the direction in which buckling would occur for the given conditions of end support and intermediate bracing rcy = radius of gyration of one C-section about its centroidal axis parallel to the web.....

因此，AISI规范第D1.1节限定连接的最大纵向间隙为：，式中 smax =连接体允许的最大纵向间隙 L=抗压构件的自由长度 rI =工字钢对垂直于给定端承和中间肋条件下可能产生纵向弯曲方向的轴的回转半径 rcy =一段U型钢对其平行于筋的质心轴的回转半径。。。。。。。

It is mainly used in the strengthening of reinforced concrete flexural members and compression member with large eccentricity.

主要适用于钢筋混凝土受弯和大偏心受压构件的加固。

X bracing is usually fastened at the intersection of the members to reduce thelength of the compression member.

十大支撑通常是互相紧扣，在十字路口的成员，以减少长度的构件。

Stress wave effect is one important parameter considered in the study and it may have some influence on the dynamic buckling of axial compression member.

其中，应力波效应也作为一个重要参数纳入到研究范围中，对轴心受压构件的动力屈曲有重要影响。

Final, some problems about axial compression member under impact load are studied, which focus on the form of impact load, damage of material, local dynamic buckling of plate. Some calculation method and research viewpoints are presented.

最后，就冲击荷载作用下轴心受压构件的若干问题进行了研究，重点集中在冲击荷载形式、材料损伤、板件局部动力屈曲三个方面，给出了一些相关计算方法和研究思路。

But this text bring up a new kind of Pre-stressed steel structure, the outstanding characteristics of the structure is combination form and self equilibrium system, the purpose is to develop the steel potential through taking full advantage of axis compression member strength break under small slenderness ratio.

本文提出一种全新的预应力钢结构的结构形式，是由自平衡的预应力结构单元拼装组成的结构体系。

Impact buckling which has few study findings relatively. So some viewpoints have not been consistent. Systematic study is made on dynamic buckling of axial compression member under impact load in this paper for that reasons.

动力屈曲问题由于时间参数的引入相比静力屈曲问题要复杂得多，特别是对冲击荷载作用下的动力屈曲问题尤甚，研究成果相对较少，对许多问题的认识尚未达成一致。

This requirement ensures that the slenderness ratio of the individual Csection between connectors is less than or equal to one-half of the slenderness ratio of the entire compression member in the case that any one of the connectors may be loosened or ineffective.

这个要求确保在任一连接件可能松脱或失效的情形下，单段U型钢的长细比小于或等于整个抗压构件长细的二分之一。

The web perforation can provide space for electrical conduits and bracing. Therefore, it has the meanings and motive for the study of C-shaped section with web openings. The strength of a compression member can be influenced by the section shape, thickness of section, length of member, and support condition.

不过，构材之厚度、加劲与未加劲、是否开孔、上下两端之接合方式，皆会影响受压构材之抗压能力，所以目前先针对C形断面构材的开孔与否及上下两端之接合方式，分别以两种尺寸来讨论，并藉由有限元素分析软体ANSYS 6.0版，来模拟构件受压时，断面的应力分布情形。

It goes back to what I told you...

现在回到我告诉过你的。。。

With a supporter in Mr Charest and an admirer in Mr Dumont, Mr Harper may be encouraged to call an election himself.

由于在沙雷那边有个支持者，杜蒙那边有个崇拜者，鼓励哈珀为自己举行一次选举。