查询词典 cathode ray tubes

Especially, cathode temperature has a strong influence on the discharge property of cathode fall region via its influence on electron emission process. This is one of the most typical properties of hot cathode glow discharge.

特别是阴极温度对放电特性的影响，它是通过热阴极的温度对热电子发射过程的影响来实现的，也是区别于常规冷阴极辉光放电的一个重要放电特征。

The cathode temperature is an important parameter during the studying themechanism on the cathode erosion and cathode electron emission, so we set up adevice of two-wavelength pyrometry.

在研究阴极烧损物理机制和阴极电子发射机理的过程中，阴极温度是一个重要的参数，因而我们建立了一套双波长高温测量系统用于测量阴极温度。

The ECM productivity of inner ratchet wheel is very high. Cathode piece is machined easily using WEDM. Its dimension is nicety. Cathode is not worn down in process,so a piece of cathode can be repeat used to machining tens or several hundred parts. The surface quality of inner ratchet wheel being machined is nice. There is no burr in the surface. Its surface roughness can reach Ra1.6μm.Its ...

应用电化学加工技术加工内棘轮，生产率很高；采用线切割加工片状工具阴极，制作方便、尺寸准确；加工过程中工具阴极无损耗，一片阴极可以重复加工几十至几百个零件；加工出的内棘轮表面质量好，无飞边毛刺，表面粗糙度可达Ra1.6 μm ；加工精度较高。

The effects of structural parameters of target cathode on magnetic field distribution during magnetron sputtering were simulated and analyzed to design a new-type rectangularly plane cathode,then the magnetic field of the designed cathode was simulated and analysed.

文章模拟分析了结构参数对磁控溅射阴极磁场分布的影响，设计了一种新型的矩形平面磁控溅射阴极，并对设计的阴极磁场进行模拟分析，结果表明有效提高了靶材表面磁场分布的均匀性。

The thermionic emission properties of rare earth doped molybdenum cathode and impregnated cathode with sub-micron scandia doped tungsten matrix, and the secondary emission property of rare earth doped molybdenum cathode have been studied in this paper.

研究了稀土钼阴极的热发射、次级发射及亚微米结构钪钨基扩散阴极的热发射性能。

As a nondestructive technique to measure the inner fine structure of the cathode, the ICT has the unique advantage. We discussed the emission mechanism of thermionic cathode, and tried to explain the excellent performance of mixed metal cathode by Richardson formula and Muller's computational model.

就当前钡钨阴极发射机理的两个主要理论模型作了自己的探讨，并初探了钡钨阴极中钡的供应机制及发射寿命预测的问题，而且用理查逊公式的推导和Muller计算机模拟法解释了混合基钡钨阴极的优良性能。

The cathode phenomena in hollow cathode arc discharge in vacuum wereinvestigated systematically. The influence of welding parameters on active zone ofhollow cathode , arc appearance and voltage-ampere curve was investigated.

小电流的发散态电弧能量密度低，柔性大，可作为局部加热热源进行真空钎焊；大电流的可作为理想的熔焊热源，进行各种难熔易氧化金属在真空条件下的高质量焊接。

Through designing of composition and structure of the bioactive graded coating,innerstress and its distribution in the coating were analyzed and calculated, the resultsshowed that when composition distribution coefficient n was 1.5, a reasonable stressdistribution could be got, that was at the beginning of deposition the suspension containingrichly BG granules was used so that a rich BG granules layer, a good transitional layerbetween BG layer at the bottom and the coating could be obtained at the titanium alloy side,the bottom of the coating; the stress value near the interface and surface and its character,pressure stress or tensile stress, were decided by the character of its composition itself.Changing composition distribution coefficient n could only change the variation tendency ofstress in the coating, but did not change the stress distribution rule in the coating. Thethinner the coating is, the sharper stress variation in the coating is, which does not mean thatthicker coating is better because the thicker the coating is, the little the permitteddeformation of coating is, so the coating thickness should be thinner, for example, about50μm for bending applications, but for applications only bearing pure shear stress, such asroot of tooth implant, the coating can be thicker little, for instance, about 80～100μm. The study on electrification characteristic and electrophoresis deposition of HAand BG granules in aqueous and non-aqueous solution system found that EPD almost didn'toccur in aqueous solution system. However, because HA granules take position charges inabsolute alcohol, a homogeneous EPD be carried out on the cathode titanium alloy slice, but taking negative charge in absolute alcohol the BG granules not be deposited on the cathode. A guided HA crystallizing, 100～300nm, on surface of the BG granules be realized by metathetical reaction, which cover BG granules with HA microcrystals and make the covered BG granules taking position charges in absolute alcohol, sequentially realize the EPCD of the BG and HA granules on the cathode, so it is feasible to make a titanium alloy/BG/HA bioactive graded coating by making use of EPCD technology. The corrosion experiment of rich boron bioglass coating and plasma spray coating showed that split phase, rich boron and rich silicon phase, occurred during its preparation. In basic medium the corrosion behavior of 〓 BG coating showed uniformity corrosion, the corrosion mostly occurred at rich boron phase area, therefore batch formula design of BGshould avoid the occurring of split phase. The corrosion appearance of plasma spray coatingappeared a non-uniform corrosion, mostly occurred at the edge of the laminated HA moltendrops, and emerged an accelerated corrosion tendency, which will easyly lead to corrosioncrackles extending to the interface and the happening of osmotic interfacial corrosion, thatmay be one of the major reasons leading to the coating cracking-off in the later period. Thetesting results of thermal expansion coefficient of 〓 and 〓BG showed the thermalexpansion coefficient of 〓 BG matched with that of titanium alloy better, and 〓 BG couldsinter with titanium alloy into densification enamel layer at low temperature (720℃).

将Ti6Al4V合金在1000℃下进行真空热处理会降低其力学性能，且合金内的V元素会向表面富集，因此，钛合金真空热处理和表面涂层的烧结温度不能过高，即应低于其相转变点；通过对生物活性梯度涂层的组成和结构的设计，分析和计算了梯度涂层内的应力大小和分布，结果表明：对于本研究，当成分分布系数n=1.5时，可以获得较合理的涂层力学性能，即在沉积开始时，采用富含BG颗粒的悬浮液，以便在钛合金侧获得同底层BG有良好过渡的富BG涂层；梯度涂层界面和表面的应力大小、性质由材料组成本身的性质决定，改变成分分布系数，只能改变涂层内应力变化的趋势；涂层的厚薄不影响涂层内的应力分布规律，但涂层越薄，涂层内的应力变化越快，但这并不意味着涂层越厚越好，因为涂层越厚，涂层允许的变形越小，对于应用于弯曲受力部位的涂层而言，涂层应薄一点为好(50μm)；而对于仅纯受剪切应力的部位，如牙根种植体，涂层可适当加厚(80～100μm)；通过对HA和BG颗粒在水溶液体系和非水溶液体系中的带电特性和电泳沉积的研究发现，它们在水溶液体系中很难发生电沉积；在无水乙醇溶液中，HA颗粒带正电，可在阴极钛合金片上发生均匀的电泳沉积，而BG颗粒则带负电荷；利用复分解反应法，可以制得100～300nm的HA，通过诱导HA在BG颗粒表面结晶，可对BG颗粒进行表面包覆，获得了被HA包覆的BG颗粒，改变了BG颗粒表面的带电特性，使BG和HA颗粒在无水乙醇中均带上正电荷，从而实现了HA和BG颗粒在阴极上的共沉积。

Due to the cathode oxidizability and electrolyte instability, some primary reactions, such as electrolyte decomposition, cathode materials dissolution and self-heating redox reaction, arised at the cathode/electrolytes interface in Li-ion batteries, which deteriorated the electrochemical properties and safety of the batteries.

锂离子电池中的正极/电解液界面反应：电解液的氧化分解、正极材料腐蚀溶解及正极材料的自热氧化还原反应等，均能对电池的电化学性能和安全特性产生不良影响。

Trans-Blot Cells and Systems 170-3825 Trans-Blot Cell With Wire Electrodes and PowerPac HC Power Supply, 100120/220240 V, includes 2 gel holder cassettes, buffer tank, lid with power cables, 4 fiber pads, 1 pack precut blot absorbent filter paper (15 x 20 cm), power supply, power cord, instructions 170-3850 Trans-Blot System With Plate Electrodes and PowerPac HC Power Supply, 100120/220240 V 170-3853 Trans-Blot System With Plate Electrodes, Super Cooling Coil, and PowerPac HC Power Supply, 100120/220240 V, includes 2 gel holder cassettes, buffer tank, lid with power cables, 4 fiber pads, 1 pack precut blot absorbent filter paper (15 x 20 cm), power supply, power cord, instructions 170-3910 Trans-Blot Cell With Wire Electrodes, includes 2 gel holder cassettes, buffer tank, lid with power cables, 4 fiber pads, 1 pack precut blot absorbent filter paper (15 x 20 cm) 170-3939 Trans-Blot Cell With Plate Electrodes and Super Cooling Coil, includes 2 gel holder cassettes, buffer tank, lid with power cables, 4 fiber pads, 1 pack precut blot absorbent filter paper (15 x 20 cm) 170-3946 Trans-Blot Cell With Plate Electrodes, includes 2 gel holder cassettes, buffer tank, lid with power cables, 4 fiber pads, 1 pack precut blot absorbent filter paper (15 x 20 cm) Trans-Blot Cell Accessories 170-3912 Super Cooling Coil, required for all high-intensity transfers 170-3913 Gel Holder Cassette, includes 2 fiber pads 170-3914 Fiber Pads, 15.5 x 20.5 cm, 6 170-3920 Trans-Blot Standard Wire Electrode Card, cathode 170-3921 Trans-Blot Standard Wire Electrode Card, anode 170-3922 Trans-Blot Cell Buffer Tank 170-3923 Trans-Blot Cell Lid With Power Cables 170-3943 Trans-Blot Platinum Anode Plate Electrode 170-3944 Trans-Blot Stainless-Steel Cathode Plate Electrode 170-3945 Trans-Blot Plate Electrode Pair, platinum anode and stainless-steel cathode 16 规格:说明: Trans-Blot Plus

电泳转印槽组件 1。缓冲液槽及带有电缆的盖 2。凝胶支架转印夹 3。纤维衬垫 4。电极丝 5。电极板 6。特级冷却芯 Trans-Blot 转印槽是功能灵活的转印设备，可理想地用于多种转印应用。Trans-Blot 转印槽特点包括：*能进行多胶转印，可容纳3 块PROTEAN I xi 凝胶、6块Criterion 凝胶、12块Mini-PROTEAN 3 或Ready Gel 预制胶*多组参数灵活可设，可调节的电压设置（从30 V 的过夜转印到200 V 的1 小时快速实验）*电极间距设置为8 cm 用于标准印迹杂交，或设置为4cm 用于高强度印迹杂交*可选择板式电极：涂有铂金的钛作为正极，不锈钢为负极，能提供高强度电场和比其它电极更高的电流密度。或选择较经济的铂金电极丝*通过特级冷却芯和水循环仪来调节温度―是天然酶（4°C）或高强度转印的理想选择，随着转印时间增加（多达24 小时），不会引起缓冲液耗竭（在高强度转印中必须使用冷却芯，也推荐用于所有板式电极的应用）*带铰链的凝胶支架转印夹能避免滑动，确保凝胶与印迹膜间的紧密接触；每个转印夹都有颜色标记以保证在转印槽中的正确定位 Trans-Blot 转印槽的锁闭凝胶支架转印夹系统。转印夹（1）支撑凝胶（2）印迹膜（3）两侧有纤维衬垫和滤纸（4）确保凝胶三明治内的完全接触。凝胶夹垂直插入缓冲液槽中（5）。

But GST= 0.156, Nm=1. 588. As a result, the foundation of Youyongchi Avicennia marina population was the result of the migration of hypocotyles and human factors.

这项工作可以为海岸防护林中新引进种类的判定以及为研究种群建立者效应方法的确定提供科学依据。

The two-dimensional CDRC-ADI-FDTD update equations for collision unmagnetized plasma are induced. The unconditional stability of the CDRC-ADI-FDTD formulation for collision unmagnetized plasma is obtained by the examples.

推导了碰撞非磁化等离子体中的二维CDRC-ADI-FDTD迭代公式，并用算例验证了碰撞非磁化等离子体CDRC-ADI-FDTD算法也是无条件稳定的。