驱动电路

The chip of CH250 and big power triode transistors were designed to build a set of step motor driving circuits. Only two signals of the DSP CP and DIR from EVB are needed for the control of the step motor.

偏差调整单元则由DSP与步进电机驱动电源组成，该电源采用步进电机脉冲分配器CH250，配以单端驱动电路，由事件管理器模块EVB输出CP脉冲与DIR信号经过驱动电路来对步进电机进行控制。

The controller includes multi-channel switching circuit, interface and conversation circuit, input and output circuit, manual button control circuit, LCD driving circuit, real-time clock circuit, preparedness store circuit, keyboard processing circuit and dial switch circuit.

该控制器硬件包括多通道切换电路、接口及转换电路、输入输出电路、手动按钮控制电路、手动与自动切换电路、液晶显示驱动电路、实时时钟电路、预案存储电路、键盘处理电路、拨码开关电路。

Using retriggerable monostable multivibrators to provide the trigger signal and double MOS driver to drive the LD, with a lot of experiments, emulations and comparisons, the variable frequency, pulse width and power driver circuit is designed. And the pulse frequency and width can be changed easily for its situations.

然后用电子多频振荡器提供驱动信号，用双MOS驱动器来驱动半导体激光器，通过大量的实验、仿真、分析、比较，设计出了方便可调的大功率LD的驱动电路，该电路的脉冲频率和脉冲宽度可方便调整。

An electrical circuit element used to introduce reactance into the circuit .

用以防止被驱动电路对驱动电路的影响的一种隔离电路。

The chip consists of a power mos, mode select circuit, driving circuit, and two series of controller circuit. The controller consists to the active current sensing circuit, sample and hold circuit, hysteresis current comparator, voltage to current converter, error amplifier and non-overlap circuit.

晶片包含一组功率电晶体、模式选择电路、驱动电路及二组控制电路，控制电路主要架构有主动式电流感测电路、取样保持电路、磁滞电流比较电路、电压对电流转换电路、误差放大器及非重叠电路。

Based on theory of strobe imaging the EL6249C is used to design a set of strobe driving circuit to drive high light LED to generate strobe light for MEMS dynamic test.

文中根据频闪成像原理，利用EL6249C设计了一套频闪驱动电路，该驱动电路可驱动高亮LED ，以产生MEMS动态测试中所需的频闪光，为后续MEMS器件的动态特性提取和分析做准备。

For carrying out a small physical volume and high reliability of the motor driving and control,by using HIP4081 chip and ALN hybrid integrated technology,a hybrid integrated technology H bridge circuit based on HIP4081 is designed to control bidirectional circumrotation and speed regulation of the motor.

摘 要：为了实现小体积、高可靠的电机驱动与控制，利用HIP4081专用芯片和ALN厚膜混合集成技术，设计一种基于HIP4081的厚膜H桥电机驱动电路，完成了H桥式驱动电路对电机双向转动和调速的控制。

Subcircuit models are designed and simulated, which includes Bias Current Source, Voltage Reference, Error Amplifier, PWM Comparator, Driver Circuit, Protection Circuits for Over-temperature, Over-current. At last, combined with periphery component, the circuit is simulated, and the result meets the anticipant requirement.

并对集成电路内的各个模块包括电流偏置电路、基准电压电路、误差放大电路、三角波振荡发生电路、PWM比较电路、驱动电路、过热保护电路和过流保护等进行了具体的设计和仿真，并对整体应用电路进行了仿真，结果均达到了预先设定的指标。

On the second and third plan, the quadrupler was made up of UMS's CHX-2089 and Minix's XX-1000 MMIC multiplier. The driver circuit's area still is very small. For two MMIC doublers, the driver circuit has only one input port of+12V.

同样在很小的面积内，设计了单片驱动电路，实现单一正压12V输入情况下，满足各个单片工作所需的各脚直流驱动，结合实验结果不断调整驱动电路。

Total circuit scheme and time sequence of tool design and implementation have been designed on the AIL logging characteristic. The design and analysis for circuit unit have been carry out on the several units such as main control circuit, signal phantom circuit, signal control circuit, amplifier circuit, A/D circuit, transmitter drive circuit and power circuit.

按照AIL的结构特点，进行了仪器总体设计，设计了仪器工作电路原理和工作时序，在此基础上，进行了主控制电路、信号幻像转换电路、信号控制电路、放大电路、A/D转换电路、发射驱动电路、电源电路等单元电路的分析和设计，从而完成了仪器单元电路的设计与实现。

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严，以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆，把帆卷起，系住。