轴切的

In this paper, the particle breakage rule and breakage energy are studied during triaxial shearing, on which the associated equation is established.

论文根据堆石料的三轴试验成果，研究了粗粒土三轴剪切过程中的颗粒破碎规律和破碎耗能，提出了相关计算公式。

The first set of tests was that mean stress p was constant while deviator stress q changed; the second set of tests was that q was constant while p changed.

做了2种应力路径下的三轴排水剪切试验：平均应力等于常数、偏应力变化的剪切试验以及偏应力等于常数、平均应力变化的剪切试验。

This paper researches the part third-order contact condition of tool and the surfaces by the contact principle of deferential geometry in to the 5-axis NC machining and analyzes the contact degree of the intersection line of the cutter and the surfaces.

运用微分几何中的切触原理，研究了在多轴数控机床中铣刀铣削圆与零件曲面的切触条件和局部坐标系下的局部三阶切触条件，并用截形对铣刀铣削圆与曲面的贴近程度进行了分析。

A-type folds and sheath folds: a-type folds are those whose axis is parallel to the elongation lineation.

a型褶皱和鞘褶皱：a型褶皱是褶皱轴与拉伸线理平行的褶皱，可以由剪切作用直接形成，或是由b型褶皱随着剪切变形的加剧改造而成，一般发育在剪切带的中心部位。

On the basis of triaxial experiment, the author discussed the relation between pore water pressure and rates of shearing, deduced the formula of pore water pressure in the set-out stage of large highspeed rockslide.

通过三轴剪切试验探讨了滑带土孔隙水压力与剪切速率的关系，推出了大型高速岩质滑坡启程活动阶段滑带孔隙水压力的计算式。

Generally, it can be divided into three types of floating stress, spindling stress and pressing stress, among which floating stress is the most important.

血管内流体压力的突然升高，在血管分叉处产生涡流；液体在血管内流动对管壁产生不同的应力，一般分流体切应力、轴向应力和压应力3种，其中流体切应力最为重要。

A circle shear device for cutting holes in sheet metal as in claim 2 wherein said means for synchronous movement of said center shafts includes: a a motion linking mechanism including a plurality of gear cogs, cog belts and a jack shaft; and b said motion linking mechanism includes a motor for powered rotation of said center shafts.

一个圈剪切装置切割孔在钣金象索赔2 ，那是说，是指为同步运动的说，中心轴，包括：一）一项议案，连接机制，包括多元化的齿轮cogs ，齿形带和一个千斤顶轴； B ）表示，议案连接机制，包括一个马达驱动旋转的说，中心轴。

Our company has already invented a series of model in long-term development, Such as Electric capacity measuring machine, energize the life-span test machine with electric iron, roller brush automation of complete sets of equipment (the cut off chamfering machine, comber machine and the woollen cloth divides a machine), blank point of the machine,electric capacity characteristic test machine, and so on.

公司在长期的发展过程中，已推出一系列成熟滚筒刷成套设备机型，如：自动热熔刷胶通用机、滚筒刷分条机、全自动切管倒角梳毛一体机、切管倒角机、循环梳毛机、支架数控成型机、自动剪线机、电容检测机、电子成型编带机、跳线编带机、轴向编带机、电熨斗通电寿命测试机、家用小电器跌落实验机、磁性自动打磨叠料机、电力电容特性测试机等。

The new type of single shaft roll cutting shearer is available equipment.

通过对滚切剪工作原理的分析及其结构的改进，指出了新型单轴滚切剪是提高剪切质量的设备。

The results show that the plasticity zone and dynamically quiescent layer become fine equiaxed recrystallisation under the thermo-mechanical effect, the grains in the heat-affected zone grow up because of the effect of friction heat. When the rotation speed is 2 500 r/min and the welding time is 12 s, good joint is achieved, and the tensile shear strength of the joint reaches 9.24 kN. The tensile shear strength of spot increases with increasing tool rotation speed, with increasing welding time, the strength increases first, while then reduces. The microhardness of plasticity zone is high, but is slightly lower than that of the base metal, the minimum value of microhardness is in the heat affected zone. When the energy input of joint is high, the fracture type of spot is mode Ⅰ, and the tensile shear strength is high; on the contrary, when the energy input of joint is less the fracture type of spot is mode Ⅱ, and the strength is low.

结果表明：塑性区和动态静止层的晶粒在热和力作用下发生动态再结晶形成细小的等轴晶，热影响区的晶粒在摩擦热作用下长大变粗；搅拌头旋转速度为2 500 r/min，焊接时间为12 s时，可以获得力学性能较好的焊点，焊点的剪切强度达到9.24 kN；焊点的剪切强度随搅拌头旋转速度的增大而增大，随焊接时间的延长先增大后减小；塑性区的显微硬度较高，但略小于母材，接头显微硬度的最小值分布在热影响区；焊点热输入量较多时，接头为Ⅰ型断裂，焊点的剪切强度较高；焊点热输入量较少时，接头为Ⅱ型断裂，焊点的强度较低。

I am sure after a few weeks of adaptation and familiarization I will have no difficulty in functioning on a daily basis in an English speaking society or in participating fully in graduate studies.

在大学的三年的学习生活不仅给予我自身的充实，更重要的是磨练和培养了我较强的自觉能力和严谨，踏实的作风以及不怕困难的精神，对未来充满了信心！

As the first volcanoes erupted, one of the gases that bellowed out was steam.

在第一批火山喷发时，喷出的气体之一就是水蒸汽。