计算不出

Analysis for testability is widely used in DFT and test pattern generation, but most testability analysis algorithms have the shortcoming of either inaccuracy or being too complicated. A new method to calculate the signal probabilities of the nodes in IC is pre-sented in Chapter 7 of this dissertation. The signal probabilities by our method is more exact than by the previous ones. A symbol of the signal probability at the fan-out node is created and is propagated to the RFON (Reconvergent Fan-out Nodes). At the RFON, the expression containing the symbol is simplified using the rule which corresponds to the law of identity in Boolean algebra. After the expression is simplified, the symbol is substituted with its numeric value. Theoretical analysis shows that this method is concise and has a low computing complexity.

可测试性分析在可测试性设计和测试生成中都有着广泛的应用，然而大部分的可测性分析方法都存在不精确或者过于复杂的毛病，在第七章中作者提出了一种新的计算IC电路节点的信号概率值的符号算法，该算法得出的信号概率值比用以往的算法法得出的要更准确，也更简洁，针对电路中的扇出节点重汇聚现象，我们在每一个扇出节点定义了一个信号概率的符号，在以后的计算中一直使用该符号参与计算，直到该符号传播至重汇聚处，利用一定的规则把含符号的表达式化简，再将符号的真实值代入，在计算符号概率的过程中定义了一个和布尔代数中的同一律相对应的运算规则，通过该运算规则，使得信号概率的结果更加准确，符号算法具有简洁方便，计算复杂度小的特点 4。

Main contents and conclusions are: 1 The ionization current was measured continuously by a charge-integration method with a computer after the introduction of radon into the chamber.

主要内容及结论：1充氡后利用计算机连续进行电离电流累积测量，得到了精细的电流随时间的变化曲线，可清楚看出氡及其子体的生成衰变造成的电离电流的生长—稳定—衰减过程，与理论计算值进行了比较，由电离电流衰减速度的变化得出氡吸附作用的影响，并测量到电离室冲洗后氡的反扩散现象；2由已知活度的标准源定出相对测量的刻度系数K值，K=24.62 Bq／pA，对同一个监测源以半年为周期进行多次测量后得出稳定性符合要求；3通过测量电离电流和气压的关系曲线以及不同气压下的饱和曲线，确定了常规的工作条件；4测量了盐酸清洗电离室内表面降低本底的效果；5不确定度分析表明相对测氡的扩展不确定度(k=2)小于5％，由本底涨落得出探测下限为0.5 Bq；6理论上对壁损失修正进行了计算，实验上保持电离室工作在饱和区的情况下，测量了不同气压下电离电流的变化，从中得出了壁损失随气压变化的规律，可以看出，电离电流的实测值和计算值随气压变化规律基本一致；当气压大于125 kPa时，端效应等其它因素造成的影响不大于2％，因而在此工作条件下，测量电离电流后通过计算修正壁损失可以实现近似的绝对测氡，提出了进一步提高绝对测量准确度的方法。

And then, this paper presents an algorithm of computing the left inverse or right inverse for these special rectangle matrices. In thenormal algorithms for solving these problems, we need O(m2n) multiplications ordivisions. The algorithms in this paper only need O + O(n2) multiplications ordivisions. The paper is built as follows.

常规的计算m×n阶不相容线性方程组的极小范数最小二乘解的算法所需计算量为O(m~2n)，而本文根据特殊矩阵的特殊结构，通过两种不同的构造方式给出了两类不同的计算极小范数最小二乘解的快速算法，并给出了求特殊矩阵的左逆及右逆的快速算法，它们的计算量均为O+O(n~2)。

The main work and innovation1 In general , a image compression method has different effect to different image . Some are fit for image which has much high frequency . Some are fit for image which has much low frequency .This paper analysis the applicability of fractal algorithm . In this dissertation , an improved algorithum is given . The basic algorithum without eight change and the joint use of quantitative coding , The compression ratio and PSNR can be adjusted , and it can get more quickly speed of coding .2 To a group of exact fractal code , the decoding image can be any resolution .With this characteristic ,choose the proper domain block and range block,this paper get an algorithum which can get higher decoding PSNR and speed than the basic fractal algorithum.3 Give a new method to calculate the scale factor . The calculation of basic algorithum is complex and enormous . The factor of scale is an important variable of the basic algorithm. Now there are two methods to calculate the factor of scale .A new method was given to calculate the factor of scale. The calculation load and complexity are reduced by the new method. Compared with the basic algorithm , the method can reduce coding time.4 The basic fractal algorithum is based on the Collage theorem and contraction mapping theorem . A mathematic model based on basic fractal algorithum is given .

本文的主要工作及创新点主要包括以下几点：1一般情况下，一种图像压缩的方法对不同特点的图像，压缩效果会有所不同，本文利用分形压缩编码对不同特点的图像进行编码，分析了分形编码对不同图像的编码适用性，利用去掉8种变换的分形编码算法与简单的均匀量化编码方案相结合，得到了一种可以调节压缩比与解码质量的分形编码方案，该提高编码速度6倍以上。2分形编码的特点之一是分形解码的分辨率无关性，即对于一组分形编码可以将其解码到任意分辨率下，本文利用分形编码的这一特点，结合不同的量化编码方案，选择合适的定义域块与值域块及适当的编解码分辨率，得到了一种提高解码质量，编码速度提高12倍以上的加速算法。3比例因子是基本分形算法中的一个重要变量，目前有两种计算比例因子的方法，文中给出了一种新的求比例因子的方法，该方法简化了求比例因子的计算，从整体上减小了基本分形算法的计算量，简化了算法4分形压缩的数学基础是不动点定理与拼贴定理，本文根据基本的自动分形编码方法，建立数学模型对其进行推导，得到了用普通数学的极限理论解释分形编码的数学表达式，从而对由基本分形编码得到的解码图像中的像素点的值给出了确定的表达式。

In this thesis,the AM1,MNDO,MINDO/3(mainly AM1)and INDO/S-CI semiempirical MO methods were used toinvestigate the excited-state intramolecular protontransfer reactions of salicylic acid derivatives—salicylic acid,methyl salicylate,salicylaldehyde,o-hydroxyaceto-phenone,salicylamide and 3-hydroxy-picolinamide (6 conformers and 2-3 anion species);2-(2'-hydroxy-5' methylphenyl) benzotriazole(4 conformers),2-(2' hydroxyphenyl) benzimidazole (3 conformers and 3anion species),Bis-2,5-(2-benzoxazolyl)hydroquinone(3 conformers),2-(2'-hydroxyphenyl)benzothiazole(2conformers) and 7-azaindole dimer (2 conformers).Theinvestigations were described as follows.Geometry optimization,relative stability andhydrogen bonding energy First,for sylicylic acid derivative molecules,the AM1,MNDO and MINDO/3 methods were used toinvestigate ground-state geometry optimization,energies,relative stabilities and hydrogen-bondingenergies on the five kinds of the molecules(designing 6 conformers and 2-3 anion species).Comparing with experimental data,the optimizedgeometry,the order of stability,the hydrogen-bonding energies and the distances between O-O in O-H..O hydrogen bonds by AM1 method were in agreementwith the experimental data,however,the C-C bondlengths optimized by MNDO and MINDO/3 were longer,C-O and O-H bond lengths were shorter;for C-N bondlengths,the results opitimized by MNDO method werethe same as those by AM1 method,nevertheless the C-Nbond lengths given by MINDO/3 method were muchshorter.For some sylicylic acid derivatives(e.g.methyl salicylate,salicylamide),the order ofstabilities on the conformers given by MNDO andMINDO/3 methods were not in agreement with theexisting conformers deduced by experimental methods,and the hydrogen bonding energies calculated by MNDO.and MINDO/3 methods were smaller.Second,the studyon the other systems found that the optimizedgeometry of the proton-transfered product with INDOmethod could not be obtained,only could theoptimized geometry of reactant be obtained,and thecalculated hydrogen bonding energies were greater.Many results of calculation indicated that the studyon the excited-state intramolecular proton transferreaction system using AM1 method was suitable andreliable.

本论文用AM1、MNDO、MINDO/3（主要是AM1）和INDO/S-CI半经验分子轨道方法对水杨酸衍生物系列——水杨酸、水杨酸甲酯、水杨醛、O-羟基乙酰苯酮、水杨酰胺和3-羟基吡啶酰胺（6种异构体和2-3种阴离子）；2-（2'-羟基-5'-甲基苯基）苯并三〓唑（4种异构体）；2-（2'-羟基苯基）苯并咪唑（3种异构体和3种阴离子）；2，5-二间氮杂氧茚氢醌（3种异构体）；2-（2'-羟基苯基）间〓杂硫茚（2种异构体）和7-〓吲哚二体（2种异构体）的激发态分子内质子转移反应在以下几个方面进行了较系统的理论研究：几何构型优化和相对稳定性及氢键能首先以水杨酸衍生物系列分子为例，用AM1、MNDO和MINDO/3方法考察了5种分子（每种分子设计6种异构体和2-3种阴离子）的基态几何构型优化，能量、相对稳定性和氢键能计算，通过和实验数据进行比较，AM1方法给出的优化几何构型、稳定性次序、氢键能和O—H。。。O氢键的0—0距离与实验数据吻合最好，MNDO和MINDO/3方法优化的C-C键长偏长，C-O键和O-H键长偏短；对于C-N键长，MNDO和AM1优化结果差别不大，而MINDO/3给出了过短的C-N键长，MNDO和MINDO/3方法给出的有些水杨酸衍生物分子（如水杨酸甲酯和水杨酰胺）异构体的稳定性次序和实验上推测的可存在异构体结果不一致，MNDO和MINDO/3方法给出的氢键能偏低，对其他体系的研究发现INDO方法常常不能得到质子转移产物的优化几何构型，只能得到反应物的优化构型，并且估算的氢键能偏高，大量的计算结果表明AM1方法对本论文研究的激发态分子内质子转移反应体系是适宜和可靠的。

In this paper, arrangement scheme of a novel multi-star phase shifted pole changing coil was given and the methods to determine coil split ratio were analyzed. According to electromagnetic theory, 2D electromagnetic mathematical model in which stator windings were spitted coil was developed, and magnetic field distribution of the novel motor at starting was solved by finite element method, starting performance of motor was calculated. Based on energy method, rotor slot leakage reactance under different poles and different loads were calculated, and the variation of rotor slot leakage reactance with loads was gotten. Based on time-step finite element method, distribution of branch current in stator windings and operating performance were calculated and analyzed when branch was unbalance, the method to calculate circulating loss in stator windings of novel multi-star phase shifted pole changing motor was given, and the effects of the loads variation and degree of unequilibrium on circulating loss in stator windings were calculated and analyzed.

论文系统的给出了采用分裂线圈法新型多星形移相变极绕组的排列方案，进一步分析线圈分裂比的确定方法；根据电磁场理论，建立了定子为分裂线圈绕组的电机二维电磁场数学模型，并采用场路耦合法求解了新型多星形移相变极电机起动时的磁场分布，计算了电机起动性能和基于能量法计算了不同极数下起动时转子槽漏抗和不同负载时转子槽漏抗，得出转子槽漏抗随负载变化的规律；采用时步有限元法计算分析了定子绕组支路不平衡时支路电流的分布情况及运行性能，给出了新型多星形移相变极电机定子绕组环流损耗的计算方法，分析比较了负载的变化和支路不平衡度大小对定子绕组环流损耗的影响。

During the first part, investigate the numbers and location of the different nature reserve, and review about its development, discuss the cause about the rapid developmeng about the protection areas of nature around Beijing. During the second part, this paper use the Geographical Information System to analyze the different sight function, plot our distinct function about the protection area of nature around Beijing. In the third part of this paper, the ecology function was special analyzed. This paper picked up several factor about the ecology and establish mathematics model to detect the most rational ecology distribution, bring forward the new constructive, wilder constructive and combination project. In the last parts of the paper, this paper use the Geographical Information System to analyze the different brim about the protection area of nature around Beijing, calculating the p/a and figure coefficient, and bring forward the brim theory for the nature reserve and city system.

在数量布局方面，包括北京周边各个不同级别的保护区的数目、位置分配布局和发展趋势研究，探讨北京市周边自然保护区数目和面积在99年和2000年突然增长的主要原因，以及今后北京自然保护区的发展方向；在景观布局方面，主要根据不同自然保护区的空间和功能的不同，计算延庆县各个自然保护区的景观多样性指数和景观优势度指数，并结合地理信息系统和航片，划分出不同的景观功能区间，以及各个功能区间之间的相互关系；在生态布局方面，综合考察北京周边自然状况，提取多项因子，建立评价模型，计算出各项因子权重，从而对其自然保护区的生态功能布局的合理性进行评价和趋势分析，为本文提出北京市周边自然保护区新建、扩建与合并的方案提供依据；在边缘布局方面，利用边缘效应理论和研究方法，创新提出&边缘类型样块分析法&，提取多个样方并结合地理信息系统，计算p/a比和自然保护区边缘的形状系数，划出自然保护区边缘效应趋势变化图，考察北京周边自然保护区的边缘效应，以及对城市的生态边缘功能。

In order to evaluate measuring uncertainty of tensile testing result of metallic material, the mathematic model of calculating uncertainty is established and different factors of influencing testing result are determined taking rectangle head shorter proportional sample of 18mm Q235B plate as example.

为评定金属材料拉伸试验的结果测量不确定度，以轧制厚度为 18mm的Q2 3 5B板材矩形带头短比例试样为例，建立了不确定度计算的数学模型，确定了影响试验结果的下屈服力FSL、最大力Fm、试样原始厚度a及试样原始宽度b等各项因素，计算出了各种因素的标准不确定度，得出拉伸试验结果的扩展不确定度，并给出最终测量结果的表达式：下屈服强度ReL、抗拉强度Rm的最终测量结果分别为(3 0 5± 5 )MPa和(4 3 5± 10 )MPa。

Phase-lagged cyclic boundary condition is implemented by a novel method in conjunction with the developed sliding interface technique to accurately simulate the arbitrary pitch ratio rotor/stator interaction without any modifications of the physics of the problem. It's for the first time to compose the computational area into one structured grids including both rotor/stator of centrifugal or axial turbomachinery with arbitrary pitch ratio. This method can eliminate the iteration of boundary conditions on the sliding interface and calculate the unsteady flow within rotor and stator simultaneously.

为了能够在较小的计算区域内不改变叶型而真实地反映出任意栅距比时的内部非定常流场，并避免近似仍采用相位后滞周期性条件，结合本文发展的网格技术，给出了一种新的实施方法，首次将动、静叶片数不等的离心式/轴流式叶轮机械转子、静子计算区域组合在一套结构化计算网格中，动/静叶排间的滑移界面完全按内场处理，避免了每一时层内，滑移界面处边界条件的迭代计算；并保证了每一时层，滑移界面处流动参数的守恒特性。

The main research contents are as follows:1. Through massive calculation, analysis and comparison, sum up the similarities and differences between the special-shaped cross sections and rectangular cross sections in mechanical features, between reinforced concrete special-shaped columns and rectangular columns in load-bearing capacity, ductility performance and provide necessary basic concepts and data for further understanding the characteristics of the special-shaped columns;2. Through massive elastic calculations and elasto-plastic analysis, under the preconditions of satisfying the code's requirements for axial compression ratio, limit value of lateral displacement and load-bearing capacity of normal section,oblique section and beam-column joint, under circumstances of different intensity of earthquake, structure dead weight, sort of site and column grid bay dimension, the variation regularity of maximum suitable height of structure, and thus sum up the maximum suitable height of structure for code for the purpose of macro-control while deciding the design scheme;3. Make a preliminary study on the stress feature of reinforced concrete special-shaped column and Z-shaped column of which the ratio of limb length to limb thickness is between 4~5 ,and the preliminary design method is suggested;4. Through elato-plastic time history dynamic analysis of typical projects, check up the weak storey of the special-shaped column structure and yielding, breaking and collapse mechanism to satisfy the earthquake resistant requirement to buildings of remaining stand under strong earthquake;5. Derive for project use simplified calculation formula of vibration period, suitable vibration period, suitable rigidity of special-shaped column structure through theoretical analysis, and provide an easy and practical method for deciding the structure scheme economically, safely and reasonably;6. Based on the study achievements in theory and massive analysis and calculations of this paper, sum up the regularities of inner force, deformation of special-shaped column structure and seismic conceptual design, and thus the suggection of seismic design of special-shaped column structures is presented.

本文研究的主要内容如下：通过大量的计算、分析和对比，总结出异形截面与矩形截面在力学特性、钢筋混凝土异形截面柱与矩形截面柱在承载能力、延性性能等方面的异同，为深入了解异形截面柱的特点提供必要的基本概念和数据；通过大量的弹性及弹塑性计算分析，在满足规程对轴压比、侧移限值及正截面、斜截面、节点承载力抗震验算要求的前提下，在不同抗震设防烈度、结构自重、场地类别及柱网开间尺寸情况下最大适宜高度的变化规律，并在此基础上总结归纳出异形柱结构的最大适用高度规定，可用于规程，以便于在确定方案时起到宏观控制的作用；对肢长与肢厚比在4～5的钢筋混凝土异形截面柱及Z形柱的受力特点进行初步探讨，提出初步的设计方法；通过对典型工程的弹塑性动力时程分析，检验异形柱结构的薄弱层及屈服、破坏、倒塌机制，以达到建筑物大震不倒的抗震设防要求；通过理论分析，推导出异形柱结构自振周期，以及适宜自振周期、适宜刚度的工程实用简化计算公式，为经济、安全、合理地确定结构方案提供简便实用的方法；在本文理论分析、计算以及大量的研究成果基础上，总结归纳出异形柱结构内力、变形的规律及抗震概念设计内容，并在此基础上提出异形柱结构的抗震设计建议。

Methods: Five patients with parkinsonism or dystonia were assigned to general anesthesia using an modified endotracheal tube.

本实验依照人体实验之相关规定进行，五位患有帕金森氏症或肌张力异常的病人接受神经立体定位手术。

If you can benefit from this book, it is our honour.

如果您能从本书获益，这将是我们的荣幸。