满足要求

Another way to meet the requirements is to enlist the help of a licensed bondsman.

另一种途径来满足要求，是要借重持牌

This design is to dials forks the components the processing craft and the jig design, its components are the forging, has the volume to be small, components complex characteristic,Because the surface is easier than the hole to process, when formulation technological process, first the machined surface, then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, special regarding processes the big end of hole, the trough and drills the capitellum hole incline eyelet in the working procedure, Chooses locate mode which two sells at the same time, and operates the simple manual clamp way clamp, its organization design is simple, the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。

This design is to dials forks the components the processing craft and the jig design its components are the forging has the volume to be small components complex characteristicBecause the surface is easier than the hole to process when formulation technological process first the machined surface then processes other take the surface as the datumIn which various working procedures jig all uses the unit clamp special regarding processes the big end of hole the trough and drills the capitellum hole incline eyelet in the working procedure Chooses locate mode which two sells at the same time and operates the simple manual clamp way clamp its organization design is simple the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。关键词拨叉，加工工艺，专用夹具，设计

The error rate of the clock is within the allowed range, meet the requirements.

时钟精度在误差允许范围之内，满足要求。

According to the restrictive conditions, the closed domain of modification coefficients are gotten. Modification coefficients can be remodified and adjusted with the use of CAD method, and the proper modification coefficients can be obtained finally.

根据约束条件规划出变位系数的封闭区域，借助计算机辅助手段来求取符合条件的变位系数，并可进行重复修改、调整，最终得到满足要求的变位系数。

In the field of communication protocol conformance test,how to generate test sequences which satisfy the requirements is one of hot research.

在通信协议的一致性测试领域里，如何生成满足要求的测试序列一直是研究热点之一。

The correlation rate of the standard curve was 0.999 8, and the digestion duration was 15 min at the temperature of 150℃. The relative deviation of the results were less than 2%, and the standard error was between 5% and 6%.

结果 标准曲线的相关系数r=0.9998，消解时间15 min、温度150℃，测定结果的相对标准偏差小于2%，相对误差在5%~6%之间，精密度与准确度均能满足要求。

The analysis shows that the settlement observation data of subgrade surface may be used to investigate the stability and the developing tendency of subgrade settlement, and whether the correlation coefficient of curve regression meets the requirement, however, that it cannot be used to calculate post-construction settlement.

分析表明：路基面沉降观测数据可用于考察路基沉降的稳定性、后期发展趋势和曲线回归的相关系数是否满足要求，但无法直接用之进行工后沉降检算。

Corrodent rate and conductivity impossibly meet a demand by adding Ag at the same time.

单一通过添加金属Ag不可能使导电率和腐蚀率都满足要求。

The third part is the judge method and its improvement method of a piece matrix is a diagonally dominant matrix: By using the Schur repair property of matrices, gives the sufficient and necessary conditions to judge a piece matrix be a diagonally dominant matrix.

第三部分为分块广义严格对角占优矩阵的判定方法及其改进：利用矩阵Schur补的性质，给出判定分块广义严格对角占优矩阵的充要条件，并利用逐次降阶的方法，使一个任意阶矩阵A逐次降为只需要利用定义判定一个矩阵是否满足要求，从而判定A是否是广义严格对角占优矩阵。

Cynanchum Lingtai apricot production in the average weight 65 grams, the brightly-colored fruit, juicy rich, sweet-sour taste, sweet from the nucleolus, when the late Qing Dynasty famous Shaanxi, Gansu provinces, the Qing imperial court Tongzhi tribute for years.

灵台生产的牛心杏平均单果重65克，果实色泽鲜艳，汁多味浓，甜酸适口，离核仁甜，清末时就驰名陕、甘两省，清同治年间曾为朝廷贡品。

Chenopodium album,Solanum nigrum, and Amaranthus retroflexus were very susceptible to the herbicides. Polygonum persicaria and Abutilon theophrasti were relatively less susceptible to the herbicides, and Lycopersicon esculentum was not susceptible to it. The relationship between reduction rates of weed biomass and PPM values of weed leaves 2,4, and 6 days after treatment was established.

供试的6种杂草对该混剂的敏感性存在显著差异：红心藜Chenopodium album、龙葵Solanum nigrum和反枝苋Amaranthus retroflexus对该混剂最敏感，ED90值分别为47.65、71.67和29.17g/hm2；春蓼Polygonum persicaria和苘麻Abutilon theophrasti敏感，ED90值分别为96.91、114.20g/hm2；而番茄不敏感。