满足要求

The challenges of these material are screen printing and sintering process. Many long fine patterned lines should be printed on a large piece of glass and sustain a smooth, continuous and uniform line pattern; on the other hand, the sintering process is rapidly increasing sintering temperature to a peak in a short time, then cooling the glass substrate to low temperature under a short time shock.

汽车钢化玻璃除霜加热线，是采用在玻璃基板上印刷银浆，在玻璃的钢化热处理过程中完成银导体膜的烧结附着，由于烧结时间短(总时间250sec)和温度骤变条件相当苛刻，要求导电细线无脱落断线，在功率满足要求的情况下，与外蓄电池连接的电极的焊接及附着强度也有具体要求，另外耐候性及耐擦洗等后步要求也较苛刻。

It is proved by experiments that this CCD deriver completely meets the design requirements. The whole measurement system can work precisely when this driver is integrated into another measurement circuit

实验结果表明：该驱动电路完全满足设计要求，当将其集成到其它测量电路中时，整个测量系统可正常工作，且测量精度满足要求。

As required by the automobile and motorcycle industry for enhance the quality of parts manufacturing, especially the "zero defect" was proposed, the sample testing by traditional technique has been unable to meet the requirement, to be instead of the entireness testing which testing the quality of parts manufacturing one by one. That means can check the quality after the parts manufacturing finished, removing the defect parts in time to avoid go to the next working procedure.

随着汽摩制造业对零件加工质量要求的提高，特别是零件加工质量"零缺陷"的提出，传统的零件抽样检测方式已不能满足要求，取而代之的是对每个零件的加工质量逐个进行检测的完全检测方式，即在零件加工完毕后能对其加工质量合格与否进行快速判别，及时将不合格零件剔除，避免其流入下道工序。

In practice, many data acquisition systems larger than the amount of data, so the system has a high storage capacity requirements of an ordinary EPROM or FLASH is very difficult to meet capacity requirements.

在实际应用中，许多数据采集系统的数据量都比较大，因此对系统的存储容量有很高的要求，一般普通的EPROM或FLASH的容量都很难以满足要求。

As a result, the conclusions are drawn that it is hardly possible to automatically recreate the hexahedral elements with satisfied quality on an arbitrary 3D solid model, since the algorithm relates on how to handle many specific problems, such as geometric singularities and degeneration.

结论指出，基於在任意几何形状的三维实体上实现全自动生成满足要求的六面体网格的通用算法非常复杂和困难，涉及许多具体的特殊问题的处理，而且基於畸变后边界节点生成满足拟合精度的几何实体也是如此。

We study the attractive manifold method of the iterative learning control for a class of degenerate systems in the chapter Ⅲ. When the learning control systems don't satisfy the convergence condition, we present the learning control method satisfying the condition by constructing a stable and attractive manifold corresponding system. This method makes the system with better robustness.

第三章主要研究了一类退化系统目标跟踪的迭代学习控制的吸引流形方法，在系统不满足一般收敛条件的情况下，我们通过构造一个相应于所给系统稳定而吸引的流形，导出所满足要求的迭代学习控制，该方法对系统有较好的鲁棒性。

When the disturbing potential of 1m2/s2 accuracy, or the approximate velocity of accuracy less 2mm/s in the formula of the rotation of the gravity potential is required, the satellite orbit data not satisfied the potential rotation computing demand are rejected from the GFZs Rapid Science Orbit and TUMs ReducedDynamic Orbit. If the disturbing potential is desired 05m2/s2 at satellite track, the satellite velocity required in formula of the rotation of the gravity potential should be recomputed or the GFZs Postprocessed Science Orbit is adopted.

当要求在卫星轨迹处获得1m2/s2精度的扰动位时，也即要求位旋转效应公式中卫星速度的近似精度小于2mm/s时，GFZ的快速科学轨道、TUM的约化动力法轨道只需要剔除那些速度精度不满足要求的卫星轨迹点；当要求在卫星轨迹处获得05m2/s2精度的扰动位时，应当重新估算上述轨道的速度信息，或采用精度更高的GFZ事后科学轨道。

The results show that the stress of clack box is lower than the yield limit of the material. The safety factor is between 1.8 and 3.2, and the distortion of clack box is in the permission scope. The static strength and stiffness satisfy the request, and the life of clack box exceeds 107, which meets the requirements.

研究结果表明，在3种载荷工况作用下阀箱应力均低于材料的屈服强度，其安全系数为1.8~3.2，且阀箱的变形在允许范围之内，阀箱静强度及刚度满足要求；阀箱疲劳寿命大于107，也满足要求。

This paper uses LIZHENG to check the stability of the retaining wall. Both of them aren't meet the requirements. And the bearing capacity at the toe of the retaining wall which belongs to AB slope isn't meet the requirement.

利用理正软件对边坡的挡墙进行稳定性验算：两段边坡下挡墙的抗滑移稳定性均不满足要求，且AB段挡墙墙趾处的承载能力也不满足要求。

Where the accuracy of construction location and distance of total station,hight measurement of total station, traverse accuracy controlled by error of closure of angle polygonometry and coordinate relative error of closure or not satisfy the requirement of construction were analysised and discussed.

主要对全站仪放样距离要求和精度、全站仪高程测量以及导线测量中方位角闭合差和坐标相对闭合差来控制导线精度能否满足施工的要求等问题进行分析和探讨，以使测量精度满足要求。

Objective: To study the effect of polycythemia on blood oxygen saturation.

裴蕾目的：观察RBC剧增而引起的高粘血症对血氧饱和度的影响。

Based on SIMPLER algorithm in the curvilinear body-fitted coordinates, the calculations were performed for Pr=0.7, Re=10~1000 on non-orthogonal non-staggered grids which are generated by elliptic equation systems.

采用曲线坐标系下压力与速度耦合的SIMPLER算法，数值研究了周期性渐扩渐缩波纹通道内脉动流动与换热情况，流动Re数的范围为10~1000，Pr数为0.7。