溢流的

At the same time, large angular acceleration will cause impact in the hydraulic system.

溢流缓冲主要是降低瞬时压力冲击。建立相应的功率状态方程。

Based on theoretical analysis and model experiment, design of open channel rotor is presented in the paper. The following is included: overall design of system, coolant feed and discharger beside the axis, design of rotor winding, overflow, steam exhausting way in the channel and so on.

论文在理论分析和模型实验的基础上设计了开放管道式蒸发冷却转子方案，其中包括：整体结构设计、轴边进液和余液排出装置、转子线圈结构设计、溢流装置设计和槽内排汽孔方案设计等。

The paper calculates and analyses an coupling oscillating mode trait of chute -flow-dam body and the dynamic stability of the chute of overfall concrete face rockfill dam by using ANSYS finite element software and the theory of fluid-solid coupling.

采用ANSYS有限元软件和流—固耦合理论[1，2]，计算、分析了溢流混凝土面板堆石坝的泄槽—水流—坝体的耦合振动模态特性和泄槽动力稳定性，同时应用随机振动理论对脉动压力作用下的泄槽及地基的动力响应作出了定量估算，与原来的双渐方法的结果进行了比较，验证了计算结果的合理性，进而分析了坝体动弹模和堆石厚度对系统动力特性的影响。

During this time the read clock will abruptly speed-up or slow-down to avoid an overflow or underflow condition.

在这段时间里读时钟会突然加速或慢下来，以避免溢流或底流的情况。

With the different distances between fissures and Laoheishan volcanic cone and the types of lava flows (sheet lava flows or small sub-overflows), the tension fissures show the different features.

随着距离老黑山火山锥位置的不同和熔岩流的类型(如席状熔岩流、小规模次级溢流体)不同，张裂呈现不同的特征。

The equipment provided in process are: jig sorting mainly to deal with overflow flotation, jigging in the coal and coal flotation tail mixed into the power plants, waste shipped to the Waste Dump, block coal jigging dehydration, floating Coal election at the end of filtration and hydraulic flow classification Desliming, dehydration through the belt to the Coal Wharf.

本设备所规定的工艺流程是：以跳汰选别为主，浮选处理溢流，跳汰中煤和浮选尾煤混合入电站，矸石运向矸石山，跳汰块精煤脱水、浮选精煤过滤与水力分级底流脱泥、脱水通过皮带运到精煤仓。

At last, the configuration of a relief valve were improved, the cavitating flow simulation.

最后，对溢流阀阀芯形状进行了改进，通过对不同结构的化实验和噪声测试，实验结果与流场分析结果一致，改进后的阀气穴强度和噪声均得到降低。

LIQUID FLOW MEASUREMENT IN OPEN CHANNELS BY WEIRS AND FLUMES.

NF X10-312-1986 用溢流堰和水槽法测量明渠中的液流。

At last, according to the effect of orifice configuration on the cavitation, the several poppet configurations of a relief valve were designed in order to suppress cavitation, the cavitating flow simulation for different configuration were performed and compared in ordet to find a optimal conriguration.

最后，针对阀口形状对气穴的影响，为了抑制阀口气穴，对溢流阀阀芯形状进行了改进，设计了几种不同的阀芯结构，分别对不同的阀芯进行了气穴流场分析和比较，来寻求优化的阀芯结构。

Traditional plastic injection molding machine relies on constant rate pump in oil supply, and each action in the process of plastic injection may have different requirements on speed and pressure. The surplus oil flows back to the oil tank through the proportioning valve in the way of flooding adjustment. In the whole process, the rotation speed of motor remains unchanged, so the oil volume is fixed as well. Furthermore, the action is intermittent, and not of full load, so a great amount of oil is wasted.

传统的注塑机是采用定量泵供油的，注塑过程的各个动作对速度、压力的要求也不一样，它是通过注塑机的比例阀采用溢流调节的方式将多余的油旁路流回油箱，在整个过程中，电机的转速是不变的，故供油量也是固定的，而由于执行动作是间隙性的，也并不可能是满负载的，因此定量供油就有很大的浪费空间。

I'm strongly against the death penalty — it's an eye for an eye.

我不赞成死刑——这是以牙还牙的报复行为。

And to get you the support you need, we're enlisting all elements of our national power: our diplomacy and development, our economic might and our moral suasion, so that you and the rest of our military do not bear the burden of our security alone.

并给你们所须的支援，我们正徵召国家所有各种的力量：我们的外交及发展，我们的经济力量与道德劝说，所以你们与其他军人不须要孤独地负起国家安全的责任。