弯曲

The invention orginates from the fact that most of the concrete reinforcement loops needed in practice can be divided up into relatively small number of types of loops which are characterized by a predetermined sequence of points of bend with a fixed sense of direction and amount of the angle of bend, in which case the loops of the same type differ from one another only in the lengths of the individual sides of the loops between the points of bend, or from one end of the loop to the first point of bend, and from the other end of the loop to the last point of bend.

问题补充：不要软件翻译的，最好自己翻译，起码通顺的这项发明orginates的是钢筋混凝土的循环需要在实践中最可分为相对的，是由弯曲点的序列特征与预定的方向和角度的数额固定感循环类型的为数甚少的事实弯曲，在这种情况下，同类型的循环，从彼此的不同只是在弯道之间，或从一个循环结束第一点弯曲点的循环个人边长，从另一端循环的最后一点弯曲。

Distobuccal root canals were found obvious curve out by the rate of 80% in mesiodistal direction, 45% in buccolingual direction.

目的：分析上颌第一恒磨牙根管弯曲发生情况、弯曲位置、弯曲方向及弯曲程度。

MB1 root canals of the mesiobuccal root canals in maxillary molars were found obvious curve out by the rate of 82.5% in mesiodistal direction, 77.5% in buccolingual direction and there is no difference of curvature degree in the two directions.

结果：1上颌第一磨牙腭侧根管通畅、较直。2远中颊侧根管在近远中方向有80%，颊舌方向有45%出现大于5的明显弯曲，弯曲位置多位于根中1/3，且近远中向的弯曲明显大于颊舌向(P.05)。3上颌第一恒磨牙近中颊根颊侧根管在近远中方向、颊舌方向分别有82.5%、77.5%出现大于5的明显弯曲。

Choice of materials for Q235, The choice program is stamping process Piercing blanking -- thinning Burring -- Wedge-bending -- U-shaped curve In this program of cost savings but also appropriate to increase production efficiency, use of this program will mainly involve the following four die : Punching blanking die;(2) thinning Burring die;(3) Wedge-bending modulus;(4) U-bending modulus.

选择的材料为Q235，选择的冲压工艺方案是冲孔落料--变薄翻孔--斜楔式弯曲--U型弯曲，此方案在节约成本的同时也适当的提高了生产的效率，采用此方案将主要涉及到以下四套冲压模具：（1）冲孔落料模；(2)变薄翻孔模；(3)斜楔式弯曲模；(4)U型弯曲模。

And for the stress in the directional direction, which is imposed on the lathe-bed, the bending plane is an epiplastron, therefore, the batten wall pore should be designed in the epiplastron.

而当孔的位置是位于弯曲中性轴附近的时候，其对弯曲刚度的影响比较小，而当其远离中性轴即靠近边缘的时候，对弯曲刚度的影响就越大，所以应该将板壁孔布置在弯曲中性轴附近，这样可以减少孔对床身刚度的影响。

And for the stress in the directional direction, which is imposed on the lathe-bed, the bending plane is an epiplastron, therefore, the batten wall pore should be designed in the epiplastron.

而当孔的位置是位於弯曲中性轴附近的时候，其对弯曲刚度的影响比较小，而当其远离中性轴即靠近边缘的时候，对弯曲刚度的影响就越大，所以应该将板壁孔布置在弯曲中性轴附近，这样可以减少孔对床身刚度的影响。

Radiograph of teeth in mesiodistal direction were taken.

结果 ：单根单根管上颌第二前磨牙的根管弯曲仅有 2个，单根双根管牙齿的根管明显弯曲有 6个，在 2 8个双根牙中有明显根管弯曲的 6个，根管弯曲的牙齿总发生率为 6 。6 %(14 /2 13)。

During the using study of handle of forceps and pancake turner this paper discovers that handle"s crooking is an important factor which affects product"s ergonomical performance and is helpful to improve the product"s usability, and that crooked angle of handle exists an optimum value, but the best crooked angle of handle of different product is different, if the optimum value is found the product"s using study should be done.

本文从镊子柄和锅铲柄的使用性研究中发现：手柄弯曲是影响产品人机工程学性能的一个重要因素，它对提高产品的可用性有着很重要的意义；手柄的弯曲还存在一个最佳角度。但是不同产品手柄的最佳弯曲角度是不相同的，倘若要获得某产品手柄的最佳弯曲角度，还必须进行该产品的使用性研究。

Iron bars will bend and break , bend and break, bend and break. Iron bars will bend and break, my fair lady.

铁栏会弯曲和折断，弯曲和折断，弯曲和折断，铁栏会弯曲和折断，我美丽的淑女。

Iron bars will bend and break ,bend and break ,bend and break , iron bars will bend and break,my fair lady. hear is a place that I have fun ,I have fun ,I have fun , hear is a place that I have fun ,my fair lady.

铁栏杆会弯曲和断裂，弯曲和断裂，弯曲和断裂，铁栏杆会弯曲和断裂，我的小女孩，这地方真好玩儿，真好玩儿，真好玩儿，这地方真好玩儿，我的小女孩。

It goes back to what I told you...

现在回到我告诉过你的。。。

With a supporter in Mr Charest and an admirer in Mr Dumont, Mr Harper may be encouraged to call an election himself.

由于在沙雷那边有个支持者，杜蒙那边有个崇拜者，鼓励哈珀为自己举行一次选举。