压缩气体

It is assumed that it is adiabatic compression during start-up process before the atmophere pressure in flow passage rise to relief pressure, the thermodynamic equation, momentum equation and rigid water hammer theroy have been applied for the analysis and calculation the variation law of air during this transient process.

假设流道内气体未达虹吸驼峰顶处真空破坏阀排气压力前的起动过渡过程处于绝热压缩状态，运用能量方程结合动量方程和刚性水击理论，计算分析出了流道中的气体压力在起动过渡过程中的变化规律。

The attractive force increases as a gas is compressed and its molecules are brought closer together.

随着气体被压缩，气体分子之间的距离缩小，引力增大。

On the basis of dual porosity theory,the well test interpretation model which considers the variation of krg versus the volume of liquid is also established and resolved by the implicit method numerically.

摘要通过分析凝析气藏的相图，建立了凝析液饱和度随压力降的变化规律，并回归得出了相应的公式；同时通过对气体压缩因子、黏度随压力、温度的变化，建立了这些参数和无因次压力的关系；在双重介质地层假设的基础上，建立了在试井过程中凝析气相对渗透率随凝析液饱和度变化的凝析气藏试井解释数学模型，采用隐式迭代的方法进行了求解并进行了参数敏感性分析；结果表明：凝析液的饱和度对凝析气藏试井的压力及压力导数曲线有着很大的影响，早期由于凝析液的析出，阻碍了气藏的流动，导致压力及压力导数曲线上升；在凝析液饱和度达到峰值之后，随着凝析液的挥发，凝析气的相对渗透率逐渐恢复，压力及压力导数曲线又回归到正常的径向流位置；由于裂缝和基岩之间的压力差，使得裂缝弹性储容比在测试过程中发生变化，进而影响了压力及压力导数；窜流系数和裂缝弹性储容比的变化决定了窜流段发生的早晚和程度；而基岩中气体黏度的变化使得窜流的发生稍微滞后。

In order to get the high accruacy temperature andpressure compensations, the compression factor Z is used to remedy the limitation ofstate equation of ideal gas.

为了获得对气体高精度的温压补偿，利用压缩系数Z弥补理想气体状态方程的局限性。

The furnace gas is applied with the ideal gas state equation.

为了改善大型渗碳炉的均匀性，本文应用数值计算方法研究圆筒形井式渗碳炉炉膛内的流动传热过程，假设炉内流场满足定常、不可压缩轴对称条件，炉内气体可以应用理想气体状态方程。

Because of the connecting rod is one of dyadic engine of piston and main compression engine part, whose larger end hole and crank shaft link up , the small head hole links up by the wrist pin and the piston , whose effect is that the piston gas pressure is transmitted to the crank shaft , collect crank shaft gas in driving but setting a piston in motion to compress a cylinder.

因为液压是活塞式发动机和压缩机的主要零件之一，其大头孔与曲轴连接，小头孔通过活塞销与活塞连接，其作用是将活塞的气体压力传送给曲轴，又收曲轴驱动而带动活塞压缩汽缸中的气体。

Because of the connecting rod is one of dyadic engine of piston and main compression engine part, whose larger end hole and crank shaft link up , the small head hole links up by the wrist pin and the piston , whose effect is that the piston gas pressure is transmitted to the crank shaft , collect crank shaft gas in driving but setting a piston in motion to compress a cylinder. the intensity is high.

因为连杆是活塞式发动机和压缩机的主要零件之一，其大头孔与曲轴连接，小头孔通过活塞销与活塞连接，其作用是将活塞的气体压力传送给曲轴，又收曲轴驱动而带动活塞压缩汽缸中的气体。

19 Thermal inbreathing: The movement of air or blanketing gas into a tank when vapors in the tank contract or con-dense as a result of weather changes conditions (e.g., a decrease in atmospheric temperature).

3.19 热吸入：由于天气状况的变化造成罐内气体压缩而使空气和气体进入储罐内。

The connecting rod main part processes a surface being that head hole and both ends big or small are weak, more important faying face and bolt hole locating surface being the connecting rod body and cover treating /outside.

因为液压是活塞式发动机和压缩机的主要零件之一，其大头孔与曲轴连接，小头孔通过活塞销与活塞连接，其作用是将活塞的气体压力传送给曲轴，又收曲轴驱动而带动活塞压缩汽缸中的气体。

The expression for the relation between the pseudo pressure and the pressure of real gas is obtained and then applied to analyze the inflow performance relationship of gas wells.

为了更准确地描述压敏油藏真实气体渗流特性，通过引入广义拟压力函数来表征压敏油藏气体的渗流过程，使气体渗流扩散方程与单相微可压缩液体渗流扩散方程有相同的形式。

If you are unfortunate enough to the lovelorn, please tell me, I will help you out, really, please contact me!

如果你不幸失恋了，请告诉我，我会帮助你摆脱困境，真的，请联系我啦！

China's plan to cut energy intensity by 20 percent and pollutant discharges by 10 percent between 2006 and 2010 is a case in point.

中国计划在2006年到2010间降低20%的能源强度和减少10%的主要污染物排放，就是一个这样的例子。