查询词典 yield strength

The results indicate that the tensile strength,yield strength and the elongation reach 403.61MPa, 343.98MPa and 8.9%, respectively.

实验结果表明，复合材料的抗拉强度、屈服强度和延伸率分别达到了403.61MPa、343.98MPa和8.9%。

Tensile strength,yield strength and elongation of the alloys decrease and hardness increases as silico...

随Si量的增多，合金的抗拉强度、屈服强度和伸长率下降，硬度提高。

With the increase of the trametes versicolor pretreatment time, the yield and brightness of RMP decreased gradually with the obvious increase of the strength property, but the overlong pretreatment time may reduce the strength property.

随Trametes versicolor处理时间的增大，RMP成浆的得率和白度逐渐降低，强度性能有明显的提高；但过长的预处理时间会降低强度性能。

Homogenization treatment before the extrusion coarsened the grain size and reduced the tensile strength and yield strength.

挤压前均匀化热处理使挤压态合金的晶粒尺寸粗化，拉伸强度和屈服强度降低。

Although all the codes note that the angel range between strut and tie has significant influence on the designing and checking result, and corresponding specifications of angle between strut and tie have been made, yet none of the specifications relate such factors as the ratio of web reinforcement, stirrup yield strength and the compress strength of concrete, etc.

虽然各规范都认识到拉、压杆之间的夹角取值对设计和验算结果的影响，并对此做了相应的规定，但都没有明确地将腹板的配筋率，腹板钢筋的屈服强度和混凝土的极限抗压强度等因素联系起来，因此有必要对此做进一步深入的研究。

Thus. for the parent metal of the higher yield strength σ〓, it is benifit for reducing residual stress with selecting strength overmatched joint.

表明屈服强度较高的母材选用适当高强匹配的焊缝对于降低焊接残余应力是有利的。

This article provides the theoretical base on the punching, press and welding process of Q450NQR1 high strength anti-corrosion steel in application of rolling stocks, and points out the direction for rolling stocks to use high strength steel with higher yield limit for manufacturing.

为将来在铁路货车上使用更高屈服极限的高强度钢提供思路并指出方向。

The results show that the hardness values of both outside wall and crosssection of the pipe are lower and not uniform,and the tensile strength and yield strength of the lower hardness location at room temperature and high temperature (545 ℃)are not in accord with ASME SA-335/SA-335M standard....

试验结果表明，所取管段的外壁硬度和横截面上的硬度值都偏低而且分布不均匀，硬度偏低位置的室温和高温(545℃)抗拉强度及屈服强度均不符合ASME SA-335/SA-335M标准。

The tensile yield strength of 2900 psi, flexural modulus (1% cut) of 117000 psi, at -40 ℃ condition, 0.25 inches of ARM notched specimens for impact strength 180 ft-lb.

拉伸屈服强度为2900 psi，弯曲模量（ 1%切割）达到117000 psi，在-40℃条件下，0.25英寸缺口试样的ARM冲击强度为180 ft-lb。

The bending modulus for the 142000 psi, tensile yield strength of 3400 psi, 0.25 inch notched specimens for the ARM impact strength 180 ft-lb.

其弯曲模量为142000 psi，拉伸屈服强度达3400 psi，0.25英寸缺口试样的ARM冲击强度为180 ft-lb。

We stopped by the old fashion ice cream parlor Manhattan Beach Creamery for some refreshment. The "No Shoes, No Shirt, No Problem" sign on the wall epitomizes the beach lifestyle.

我们去商店区的一家老式冰淇淋店坐坐，墙上挂著「没鞋，没上衣，没问题」的牌子完全捕捉了海滩生活的随性及风格。

"If therefore", argues Bellarmine we can offer our prayers and our satisfactions in behalf of those detained in purgatory, because we are members of the great body of Christ, why may not the Vicar of Christ apply to the same souls the superabundant satisfaction of Christ and his saints--of which he is the dispenser?

" "因此，如果"，认为贝拉明（德indulgentiis ，十四）"我们可以提供我们的祈祷和我们满意的代表那些被拘留在炼狱，因为我们是成员的伟大基督的奥体，为什麼可能不是牧师基督适用於同样的灵魂满意的过剩是耶稣和他的圣人-他是在配药？