查询词典 yield strength

The results show that the mechanical properties of EVA/MH composites are improved by use of MCA, such as toughness, breaking strength and yield strength.

结果表明：MCA能够改善体系的力学性能，在提高韧性的同时，屈服强度和断裂强度也有所提高。

Results show that the actual location of the cooling curve of the steel can be adjusted by regulating the strength of the steel and the yield strength ratio of the steel can be adjusted by controlling the cooling rate o...

分析认为调节钢的实际冷却曲线位置可调节钢的强度，调节钢在铁素体相变区内的冷却速率来调节钢的屈强比。据此对控冷工艺进行优化，使产品力学性能和组织符合技术要求和用户的要求。

The simulation result of the enameling process at high temperature shows that with the increase of soaking temperature and holding time, the yield strength and tensile strength increase, and the total elongation decreases.

模拟高温搪烧时，随着温度的提高和保温时间的延长，屈服强度和抗拉强度下降，伸长率提高。

The simulation result of the enameling process at high temperature shows that with the increase of soaking temperature and holding time-the yield strength and tensile strength increase,and the total elongation decreases.

经857℃保温10 min后，钢板的屈服强度满足了不小于310 MPa的要求。预变形时的变形量对模拟高温搪烧后钢板的力学性能也会产生影响。

Selection for high specific strength had no negative effect on the obtention of high yield genotype. The correlation among fiber length, strength and micronaire of cotton for spinning high value yarn were still inconsistent. Further improvement is needed.

以上结果说明高产纺高支纱陆地棉首先应具有结铃性强、成铃多的基本性状，同时要兼顾衣分；选择高强纤维不会影响高产基因型的获得；纺高支纱陆地棉存在纤维品质不配套的问题，应进一步改良。

Experiments carried outby many investigators prove that the ultimate strength, the yield strength and hardness in-crease with the deformation, on the other hand, the elongation decreases, the impact valueand reduction of area also change.

很多研究工作者的结果都证明：极限强度、屈伏强度和硬度随着变形量而增加，但是延伸率则减小，冲击值和断面缩减率也产生了变化。

The results show that the grain size is refined by the addition of Nd or Dy, especially combined addition is better than single addition. With the addition of 0.2 % Nd and 0.6% Dy, the grain size is reduced from 150 μm to 60 μm. Combined addition with two rare earths elements makes the tensile strength, yield strength and elongation of ZK10 alloy increase to 191.0 MPa, 69.0 MPa, and 16.6%, increasing by 89%, 43%, 232% respectively, compared with ZK10 alloy without RE element.

结果表明：ZK10镁合金中分别加入Nd和Dy均能细化晶粒，且Nd和Dy同时加入的效果优于单一加入的效果，当同时加入质量分数为0.2% Nd和0.6% Dy时，合金的平均晶粒尺寸由原来的150 μm细化至60 μm，使ZK10合金的抗拉强度和屈服强度分别提高至191.0 MPa和69.0 MPa，伸长率达到16.6%，与未加入稀土的ZK10合金相比分别提高89%，43%和232%。

The results show that Bi and Sb are mainly distributed on grains and grainboundaries, and Bi on grainboundaries there are mainly simple substance Bi particles, Sb in grains are intermetallics containing stibium. The tensile strength, yield strength, elongation and variation of area of halfhard brass containing bismuth and stibium are 478.9 MPa, 295 MPa, 15.1% and 29.3% respectively. Corresponding to HPb59-1, the cutting property of brass containing bismuth and stibium is excellent. The brass containing bismuth and stibium shows excellent dezincification corrosion resistance, and the depth is 323 μm.

结果表明：添加的Bi和Sb主要以单质或化合物方式存在于无铅黄铜的相内和相界处，Bi以单质颗粒存在于相界处，Sb以化合物形式存在于相内，这对提高合金切削性能有利；添加Bi和Sb黄铜的抗拉强度为478.9 MPa，伸长率为15.1%，断面收缩率为29.3%，屈服强度大约为295 MPa；添加Bi和Sb黄铜的切削性能比HPb59-1铅黄铜的优，合金的脱锌腐蚀性能良好，脱锌层厚度约为323 μm。

As the Al/Zn ratio is equal to 10, the tensile strength and yield strength get the maximum.

结果表明：当Al/Zn比在1～15的范围内时，合金的相组织主要为α相和β相。

Both ultimate tensile strength and yield strength of AZ95 alloys are excellent.

AZ95和AZ55合金同时具有较好的常温抗拉强度和屈服强度。

Yet, Edith says, there was always money in the bank.

但是Edith说，她的银行户口里面总是有钱。

We have created a series of files that resolve this problem--one for each day of the 40 days of purpose.

我们制作一系列的档案去解决这问题---一个为标竿40天中的每一天。