查询词典 wheel base

The results prove that this method is convenient and effective, and provide a base for automatic measurement of grinding wheel.

结果表明，该方法简单有效，为砂轮自动化检测提供了一条新的思路。

Plain wire is used to cut away the finished pot from its base on the potter's wheel.

素线的作用是当一件陶器完成后用它把陶器从转盘上的基座上切下来。

Plain wire is used to cut away the finished pot from its base on the potters wheel.

素线的作用是当一件陶器完成后用它把陶器从转盘上的基座上切下来。

Plain wire is used to cut away the finished pot from its base on the potter's wheel. b9 3 B% Y4 S# T

素线的作用是当一件陶器完成后用它把陶器从转盘上的基座上切下来。

The most important tools potters use are their own hands; however, they also use wire loop tools, wooden modeling tools, plain wire, and is used to cut away the finished pot from its base on the potter's wheel.

素线的作用是当一件陶器完成后用它座上切下来。

By the worm wheel gear grinding machine grinding, precision of GB10095 Tatsu 5, base made of high strength cast iron, has two types of corner and flange structure.

齿轮经蜗杆砂轮磨齿机磨削加工，精度达GB10095的5级，机座用高强度铸铁制成，有底角和凸缘两种结构。

On this base, the system are divided into five modules: Check of front view, Check of windshield wiped area, The obstructed area check of IP formed by steering wheel, Check of binocularly obstructed angle of A pillar, and Check of rear vision for interior and exterior mirror's.

该系统分为五大模块进行研究与开发：前方视野校核模块、前风窗刮扫校核模块、仪表板盲区校核模块、A 立柱盲区校核模块、后视镜视野校核模块。

Solid minerals separation processing machine, casting emery, metal-casting shaped boxes, model base board, force piston, plastic or rubber, injected plug and pressed plug, transfer shaft, crank and other transformation sections, bearing support, teeth pulley and other gearing speed variator, ball bearing, flywheel, chain wheel including pulley block.

固体矿物分选等处理机器，铸造砂。金属铸造用型箱，型模底板，阳模，塑胶或橡胶用注模或压模。传动轴及曲柄等传动部件，轴承座，齿轮及其它变速，传动装置，滚珠，飞轮及滑轮，包括滑轮组。

This paper research rimed turbine processing technology and the development of the domestic situation base on a vast amount of information in the literature, and then, research the basic principles and the processing characteristics and the processing technology of the EDMFor given the data of several-section of a blade, the wheel and the ring, this paper use UGNX to describe the precise geometric modeling of the rimed turbine.

本文针对给定叶片若干截面型值点数据、叶冠数据和轮毂数据的情况，利用UG NX对带冠扭叶片整体涡轮叶盘进行了精确的几何造型设计研究。

According to research on space between wheel and Cart rut traverse curve of single roadway, the width of strip slab was fixed. When there was horizontal loading on slab, contact state between strip slab and base course was studied, and finite element model was established. Comparing maximum principle stress among different load position on slab, it was found that the critical loading position of cement concrete strips pavement was the middle of longitudinal joint.

对车辆轮距和单车道轮迹横向分布曲线进行分析，确定轮迹板板宽；在有水平荷载作用时，对轮迹板与基层的层间接触状态进行分析，建立有限元计算模型，对比荷载作用在轮迹板不同位置时的最大主应力，最终确定水泥混凝土轮迹路面板的临界荷位为纵缝边缘中部。

Objective: To study the effect of polycythemia on blood oxygen saturation.

裴蕾目的：观察RBC剧增而引起的高粘血症对血氧饱和度的影响。

Based on SIMPLER algorithm in the curvilinear body-fitted coordinates, the calculations were performed for Pr=0.7, Re=10~1000 on non-orthogonal non-staggered grids which are generated by elliptic equation systems.

采用曲线坐标系下压力与速度耦合的SIMPLER算法，数值研究了周期性渐扩渐缩波纹通道内脉动流动与换热情况，流动Re数的范围为10~1000，Pr数为0.7。