查询词典 vote checking

Silicon oil fit-into anterior chamber: two crystal eyes, intraocular tension has been controlled by releasing silicon oil , silicon oil fit-into one eye again, silicon oil filling exceed one month, useless of expectant treatment, after checking the reattachment of retina, doing the silicon oil dislodge from anterior chamber and vitreous cavity; there aphakia eyes by prone position and draping hypotensive drug: two iris ambitus excision aperture membrane occlusor eyes by lasering at 6 clock or perforating again., iris ambitus excision at 6 clock by lasing .one by iris ambitus excision affiliation anterior chamber plasty, acuity of vision has been elevated different degree after intraocular tension controlled.

硅油进入前房者：有晶体眼中2眼经前房放油眼压控制，其中1眼硅油再次进入前房，硅油填充亦超过1个月，经保守治疗无效，检查眼底视网膜复位后，同时行前房和玻璃体腔硅油取出术；无晶体眼中3眼经俯卧位加点降眼压药物，眼压控制，2眼虹膜周切孔膜闭者经过激光6点位打孔或重复打孔处理眼压控制，1眼作6点位周切孔重建，1眼行虹膜周切联合前房成形术，眼压控制。96眼眼压控制后，视力均有不同程度提高。

The application developer can assume that things will work, instead of constantly checking for things that might go wrong.

应用程序开发人员能确保是有效的而无需经常地检查是否会产生错误。

Correctional checking formula of melt flow ratio in injection molding was obtained by introducing a correction coefficient β which reflected the complexity degree of mold cavity. The results show that, the maximum flow ratio of 486 can be obtained when injection pressure ranges from 150 MPa to 160 MPa in Archimedes spiral mold for PP, while maximum flow ratio of 419 can be obtained when injection pressure ranges from 160 MPa to 170 MPa for PE. There is a local fluctuation phenomenon for flow ratio and corresponding injection rate in square spiral mold when injection pressure of 100, 120 and 150 MPa for PP and 130, 140 MPa for PE are reached respectively,and this phenomenon is more serious for good fluidity of melt. The average flow ratio in Archimedes spiral mold is 6% larger than that in square spiral mold for PP, and 4% for PE, the average flow ratio of PP is 19% bigger than PE in Archimedes spiral mold, and 15% in square spiral mold. The influence of the cavity profiles on the melt flow ratio is more significant for good fluidity of melt.

研究结果表明：在阿基米德螺旋线模具中，PP在注射压力为150~160 MPa时取得最大流动比485，PE在注射压力为160~170 MPa时取得最大流动比419；在方形螺旋线模具中，PP在注射压力为100，120和150 MPa，PE在注射压力为130和140 MPa时流动比及所对应的注射速率出现波动，且流动性好的熔体波动更为严重；PP在阿基米德螺旋线模具中的流动比均值较其在方形螺旋线模具中大6%，而PE大4%；在阿基米德螺旋线模具中流动比均值PP比PE的流动比均值大19%，而在方形螺旋线模具中PP的流动比均值比PE的大15%；流动性好的熔体受模具型腔轮廓特征影响大。

Mrs. Arroyo met members of her Cabinet's security cluster after checking out of hospital on Saturday afternoon.

在昨天下午检查医院后，亚罗育会见了她的内阁安全团。

However, due to traditional accounting limitation, the asset has still dissociated accounting checking system and become "no account asset" of corporation.

文章认为，衡量企业核心竞争力大小的依据是无形资产的质与量；企业核心竞争力的强弱体现为创造和提升无形资产能力的大小，而提升企业核心竞争力的资产主要是无形资产。

In this solution, to check the vacuity of the CTL formula, it is not necessary to substitute all of its sub-formulae by TRUE or FALSE, but instead, it is enough to substitute its atomic proposition, and thus the number of times for checking is linear with the number of atomic propositions.

该方法对CTL公式的空属性的探测不需要对它的所有子公式用TRUE 或FALSE替换，只需对原子命题替换，这样检验的次数与原子命题的个数呈线性关系。

From the polarity of atomic proposition, a series of CTL formulae is derived by substituting the atomic proposition with TRUE or FALSE, before they are verified by model checking tools. If one of the CTL formulae has passed the verification, then it is concluded that the system property is a vacuity.

根据原子命题的极性，用TRUE 或FALSE替换原子命题，得到一系列的CTL公式，再对这些CTL公式用模型检验工具验证，若CTL公式中有一个通过了验证，则可得出该系统属性是一个空属性。

This system has function dispersion and can deal with parameter checking, calculation, control strategy, information output and process parameters time-control. These functions will auto-run effectually and reliably that make control dispersion. Fieldbus intelligential model layer in this system is made of a few intelligential models in the fields.

该系统实现了功能分散控制，对过程参数检测及运算处理、控制策略的实现、控制信息的输出以及过程参数的实时控制等都在现场的过程控制单元中有效地、长期可靠地、无人干预地自动进行，从而实现控制功能的高度分散。

This system has function dispersion and can deal withparameter checking, calculation, control strategy, information output andprocess parameters time-control. These functions will auto-run effectuallyand reliably that make control dispersion.

在此理论基础上，论文提出了一种应用于印刷业张力联动控制的基于现场总线技术的集散控制系统DCS2000-MRT，介绍了该系统的主要功能、硬件组成、工作原理、软件设计及其实现方法。

Multi-axle box design includes: mapping the original basis for the design of multi-axle box diagram, the spindle diameter and gear modulus determination and power calculation, multi-drive axle box design, drawing more than Axlebox an important component of general layout, as well as the intensity of checking.

多轴箱设计包括：绘制多轴箱设计原始依据图、主轴直径和齿轮模数的确定及动力计算、多轴箱传动设计、绘制多轴箱总图以及重要部件的强度校核。

My father is over 60 years old, and he lifts weights every day.

我爸爸六十多岁了，他每天都练习举重。

Then in a serious tone she declared:"It doesn't pay, dear boy, to look like a ninny with one's wife the first night."

两眼湿润了，她把身子蜷得很小，这样似乎可以更好地闻闻自己。