查询词典 turtle plate

When a sudden power failure or accident or normal pump stops when the pump stops, the valve inlet water velocity to reduce stress Agency, the valve plate also fall, when its velocity is zero (that is, inlet flow rate is zero Department), large valve plate because of its own gravity and rapidly turn off (time 3s ~ 5s), the majority of water to prevent backflow, when the valve before and after the formation of a water pressure, water stress, on the one hand through the small valve at the bottom of the three slot for pressure relief vent pressure. 4 water stress from the bypass tube into the cavity patch up the control room (this process for the suction pressure chamber that can effectively absorb the energy of water), when water stress on cavity than inferior vena cava, the pressure of water promote the diaphragm down mobile , the current cavity pressure of water being squeezed out all the small valve plate slowly drop back to standby status, the process time to ease closure adjustable (3s ~ 150s), then the valve has been fully closed, watertight.

当突然停电或事故停泵或正常停泵时，阀门进水口处压力水流速降低，大阀板也随之下降，当其流速为零时，大阀板由于自身重力而迅速关闭（时间3s～5s），可防止大部分水倒流，此时阀门前后形成一种水压差，压力水一方面通过小阀板底部的三条泄压槽进行泄压。4）压力水从旁通管进入膜片控制室上腔（此过程为吸压腔，能有效吸收一部分水能量），当上腔压力水大于下腔时，压力水推动膜片往下移动，当下腔压力水全部被挤出来时，小阀板缓缓下降，恢复到待机状态，此过程中缓闭时间可调节（3s～150s），届时阀板已全部关闭，滴水不漏。

Companies from the United States, Germany, Sweden, the introduction of advanced production equipment and technology, the design annual production capacity of 100,000 tons aluminum, the main equipment has been put into deep well-type aluminum rod casting production lines, 500 tons -1650 tons of aluminum extrusion 9 production lines, 1600m / m aluminum casting production line 4, 1450m / m 2 of cold-rolled production line, 1500 m / m embossing plate production line, 1850m / m 2 cross-cutting production line, 2200m / m thick plate production line, 600m / m-1450m / m thick shear foil production line 3, 1450 m / m bending-straightening production line, 1000 * 5000m / m a CNC grinding machine, annealing furnace 20 tons of plate and strip, such as four-foil finishing equipment.

公司分别从美国、德国、瑞典引进先进的生产设备和技术，设计年产铝材十万吨，其中主要已投产设备有深井式铝棒铸造生产线两条，500吨-1650吨铝型材挤压生产线九条，1600m/m铝板铸轧生产线四条，1450m/m冷轧生产线两条，1500 m/m 压花板生产线一条，1850m/m横剪生产线二条、2200m/m厚板生产线一条，600m/m-1450m/m厚箔剪生产线三条，1450 m/m拉弯矫生产线一条，1000*5000m/m数控磨床一台，20吨退火炉四台等板带箔精整设备。

The results of numerical simulation suggest that the demisting efficiency increases as droplet diameter and gas velocity increasing and decreases as the mist eliminator plate spacing reducing, and the efficiency of arc-shaped plate with barb mist eliminator is higher than that of polyline-shaped plate mist eliminator. Droplet with a diameter under 20 mm is of low demisting efficiency.

数值分析表明：除雾效率随液滴直径的增大而增大，随进气速度的增大而增大，随除雾器叶片间距的增大而降低；带倒钩的弧形板除雾器比折形板除雾器的除雾效率高；粒径小于20 mm的小液滴脱除效率较低。

From the Olympic plate to see the development of context is so, but from the large regional market, the Olympic plate even east, the westward movement of the North expansion, but the entire plate area or belonging to the north.

从奥运板块看到发展的背景是这样，但是从大的区域市场，奥运板块甚至东，西进运动的北方扩张，但整个板块地区或属于朝鲜。

Based on this theory we deduce related equations of expansion force in plate and build elements of plate and magnetic field. After the analysis of magnetic field by FEM and some numerical computation we get the critical value of magnetic field when plate buckles.

在实现了用有限元对磁场进行三维分析基础之上，基于磁致应变假定，推导出相应等效载荷的计算公式，完成了恒定磁场作用下磁弹性矩形薄板的屈曲分析，求得了板屈曲时的磁场临界值。

Their "Zhujiaokuai" machine retains its last week, many developers have increased the push plate intensity, the performance is one of the push plate increased push plate regional expansion, particularly as the "Chinese New Year" is approaching, developers eager to offer cash mood is clearly written in the face, and how to push off "a few" in a new point meaning becomes many developers feel bothered by things.

挟&住交会&的余威，上周不少发展商纷纷加大了推盘力度，表现之一便是推盘数量增多，推盘区域扩大，尤其是随着&年关&的逼近，发展商急于出货套现的心情更是明白写在脸上，如何在推盘&着数&上搞点新意思，便成为众多发展商颇感费神的事情。

The sprue puller, being attached to the moving half, is pulled through the floating cavity plate and thereby releases the feed system which is then free to fall between the floating cavity plate and the feed plate.

位于动模上的拉料杆离开浮动型腔板并且藉此释放浇注凝料，然后它在浮动型腔板和定模板之间自由落下。

According to the shell finite element theory, the proposed method was based on the simulation of corrugated steel web by orthotropic plate element and that of flange plate by isotropic plate element respectively.

为了提高波形钢腹板箱梁的结构计算精度，本文根据板壳有限元理论提出了一种新的空间计算方法。

Practical application in accordance with its requirements, clutch design in detail the functions and working principle, designed to set out, analysis of the diaphragm spring and clutch plate follower characteristics, clutch and main parts: friction plate, pressure plate gap, such as diaphragm spring calculated.

根据其实际运用要求，设计中详细介绍离合器功能和工作原理，阐明了设计目的，分析了膜片弹簧及离合器从动盘特点，并对离合器主要部分：摩擦片、压盘、膜片弹簧等进行了计算。

The plate is fitted between one frame plate and one pressure plate and tightened by bolt.

板组合装在一块框架板和一块压力板之间，用拧紧螺栓压紧。

Must have Coordination and negotiation skill, flexible ideas, and be punctilious person.

必须具备较好的协调与谈判能力，头脑灵活，工作认真仔细

Result: 18 patients are all with simple eye.The pigment mole lies in nasal and temple sides of the ball conjunctiva,in which 2 lie in lacrimal caruncle and semilunar plica.

结果：18例患者均为单眼，色素痣大多数位于内外侧睑裂部球结膜面，2例位于泪阜及半月皱襞，经激光治疗后，10例色素痣消失，有5例行再次激光后消失，2例行第三次激光后消失，1例第四次激光后消失。