查询词典 temperature coefficient

To find and confirm the most effective preparing technology, the effect of sintering temperature and calefactive velocity upon mechanical properties and microstructures of the materials before and after infiltration were studied. In order to control the coefficient of thermal expansion and colors of the glass as well as the fluidity and infiltration property of the melted glass, we modified the formula of the glass.

在材料制备的同时，研究和比较了氧化铝升温速率及烧结温度对玻璃渗透前后材料的力学性能和微观结构的影响，以期寻求最佳的制备工艺；并改进渗透玻璃配方，以调控玻璃的热膨胀系数和颜色以及在高温下的流动性、浸润性。

By the experimental results obtained from both dilatometric and magnetic methods, it has been found that addition of 1～2% C_o maymarkedly enlarge the temperature range of low expansion coefficient forinvar steel.

根据膨胀试验和磁性试验的结果，加入1～2％的钴会显著的扩大不变钢最低膨胀系数的温度范围。

Furthermore, dropwise condensation heat flux and heat transfer coefficient are increased with the higher steam saturation temperature near the atmospheric pressure.

在大气压附近，热通量和冷凝传热系数随蒸汽的饱和温度的升高而增大。

The influence of solvent/oil ratio, thinner content and temperature on desulfurization and the distribution coefficient by extraction of a model system for diesel oil with special attention to the solvent furfuryl alcohol was investigated.

以康醇为萃取剂，在正十六烷中加入少量二苯并噻吩构成柴油模拟体系，考察了单级萃取中稀释剂含量、剂油比、温度对脱硫率和分配系数的影响。

The influence of solvent/oil ratio, thinner content and temperature on desulfurization and the distribution coefficient by extraction of a model system for diesel oil with special attention to the solvent furfuryl alcohol was investigated.

以康醇为萃取剂，在正十六烷中加入少量二苯并噻吩构成柴油模拟体系，考察了单级萃取中稀释荆含量、剂油比、温度对脱硫率和分配系数的影响。

Lamellar microstructures of TiAl alloys may be stabilized during exposure at high temperature by the addition of high-Nb element which may decrease stacking fault energy, interlamellar boundary energy and atomic diffusion coefficient.

高Nb合金元素的添加降低堆垛层错能与片层界面能，减小原子扩散系数，可能可以达到提高TiAl合金中片层组织的热稳定性的目的。

The Ventilated and Lineated Floating Disc is manufactured by FC material, resisting over 350℃; and the Friction Coefficient of the Lining Pad is between 0.505-0.668, and the operating temperature reaches as high as 1,150℃.

浮动式刹车盘！通风划线浮动式碟盘为标准FC材质，承受温度可达350度以上，来令片摩擦系数为0.505-0.668之间，工作温度最高达1150度。

The results show that the composite coating is metallurgically bonded to the substrate and the microstructure is fine and uniform. The hardness of the composite coating is up to 400 HV, which is 2.5 times that of the substrate. Under room temperature and oil lubrication condition, the sliding wear tests indicate the friction coefficient and weight loss of the composite coating are smaller than those of substrate. The worn surface of the composite coatings is much smoother than that of the substrate, without grooves and crater.

结果表明，复合材料涂层与基体形成良好的冶金结合，微观组织细小、均匀；复合材料涂层硬度达400HV，约为基体的2.5倍；在室温油润滑条件下，滑动磨损试验表明复合材料涂层摩擦系数和失重均小于基体，磨损表面划痕较浅且平滑，无明显的犁沟、粘着、剥落现象；激光表面合金化显著提高了材料的耐磨性。

The low temperature sensitivity coefficient effect of high energy nitroamine propellant through the closed vessel and interior ballistic experiments is studied.

通过高压密闭爆发器试验，研究了低温感高能硝胺发射药的定容燃烧特性，分析比较了其包覆前后的燃面变化规律。

Studied the low temperature sensitivity coefficient effect on high energy nitroamine propellant throgh the termination experiment,closed bomb experiment and interior ballistic experiment.

通过中止试验、高压密闭爆发器试验与火炮内弹道试验研究了低温感高能硝胺发射药的低温感效果。

Methods: Five patients with parkinsonism or dystonia were assigned to general anesthesia using an modified endotracheal tube.

本实验依照人体实验之相关规定进行，五位患有帕金森氏症或肌张力异常的病人接受神经立体定位手术。

If you can benefit from this book, it is our honour.

如果您能从本书获益，这将是我们的荣幸。