查询词典 temperature coefficient of resistance

Based on the experiment data of local temperature and heat transfer coefficient, some empiric formulas for the heat transfer and resistance coefficient are given.

并基于肋化表面的温度和放热系数分布测定值，得出了可供实用的肋化传热以及阻力计算公式。

According to starting performance of hybrid diesel engine of ISAD technology at low temperature, the match relationship among starting resistance torque, ISG motor power and storage battery capacitance was summarized, and influence of battery capacity was studied, which were as related to resistance torque, minimum start-up speed, electrical operating characteristics, electric transmission coefficient and thermal effects.

针对ISAD技术混合动力柴油机起动系统低温下的性能问题，该文结合柴油机的起动阻力矩、最低起动转速、ISG电机工作特性和电机热效应等因素，研究了起动阻力矩随环境温度、起动转速的变化规律，分析了起动阻力矩与ISG电机功率、蓄电池容量之间匹配关系，以及影响蓄电池性能的主要因素。

Based on the heat balance equation of the vegetation canopy layer and the assumption that its short wavelength absorptance, long wavelength emissivity, heat or moisture transfer coefficient, and bulk stomatal resistance are random, uncorrelated variables with normal distribution densities, the theoretical modeling for IR radiance statistics of vegetation canopy surface is presented by Monte Carlo simulation, with the surface radiative temperature statistical distribution given.

根据植被层能量热平衡方程，选取植被短波吸收率、长波发射率、热与水汽传输系数和气孔阻力为独立的随机变量，并假设它们均服从正态分布，利用Monte－Carlo方法，模拟计算了植被表面红外辐射的统计特性。

Based on the failure analysis of hot roll, this paper optimizedly adjusts alloy system and summarizes the experience of rolling wiresand improves ail processing properties. Then, it analyses the effects on some natural parameters such as alloy transfer coefficient, surfacing layers, welding current and arc voltage etc.. It confirms the fitting ageing technique. Also, it discusses the microscopic structural transformation back and forth ageing and the effects on hardness change of overlaying metal by some alloying elements including C, Cr, V, W, Mo, Ni, Mn, B, Re through OM, SEM and X-ray diffraction analyses. Finally the abrasive resistance, red hardness, thermal fatigue property and anti-high temperature oxidability are investigated in experimentation.

全文在热轧辊失效分析的基础上优化调整合金体系，总结了焊丝轧制的经验，改善各种工艺性能，分析了几个特性参数的影响，确定了适宜的时效工艺，并通过光学显微镜、扫描电镜和X-射线衍射对时效前后的显微组织转变以及部分合金元素如C、Cr、V、W、Mo、Ni、Mn、B、Re对堆焊层硬度变化的影响进行分析，最后通过试验考察了堆焊层金属的耐磨粒磨损性能、红硬性、耐热疲劳性和抗高温氧化性。

The effect of the tool composition on the friction and wear behavior was investigated,and the morphologies of the rake face and rear face of the tool cutting the steel in air and nitrogen were observed on a scanning electron microscope. It was found that the Al_2O_3/TiB_2 tool was dominated by adhesive and abrasive wear in low speed dry cutting; while in high speed dry cutting,the tool was characterized by oxidation wear. An oxide layer of TiO_2 was formed by way of the oxidation of the reinforcing agent TiB_2 at a very much high cutting temperature, which contributed to greatly reducing the friction coefficient and increasing the antiwear life of the tool.Such a friction-reducing and antiwear behavior of the oxide layer was enhanced with increasing content of TiB_2 in the tool composite. However,the tool showed a relatively poorer wear resistance in N_2 than in air, because N_2 acted to retard the oxidation of the TiB_2 and the formation of the oxide layer on the tool rake face.

结果表明：低速干切削时，Al2O3/TiB2陶瓷刀具的磨损机制主要表现为粘着磨损和磨料磨损；而在高速干切削时，刀具的磨损机制主要表现为氧化磨损，刀具表面经由氧化反应生成具有润滑作用的反应膜而起到固体润滑作用，从而使刀具的耐磨性能提高，随着TiB2含量和切削速度的增加，反应膜的减摩抗磨作用增强；而在切削区通入氮气时，由于刀具表面氧化膜形成受阻，刀具的抗磨能力有所降低。

First of all, the factors which influence the thermal barrier effect and the relationship between the factors and heat resistance were analyzed. Then, the paper gave the mathematical model of the effect of thermal conductivity, coating thickness, environment temperature difference, and heat exchange coefficient on thermal barrier effect.

研究主要内容如下：本文首先分析了隔热效果的几种影响因素以及它们与隔热效果之间的关系，推导出了包含热障涂层厚度、导热系数、环境温差和对流系数等在内的影响因素与隔热效果之间的数学模型。

If you are unfortunate enough to the lovelorn, please tell me, I will help you out, really, please contact me!

如果你不幸失恋了，请告诉我，我会帮助你摆脱困境，真的，请联系我啦！

China's plan to cut energy intensity by 20 percent and pollutant discharges by 10 percent between 2006 and 2010 is a case in point.

中国计划在2006年到2010间降低20%的能源强度和减少10%的主要污染物排放，就是一个这样的例子。