查询词典 surface

The fluffy film may fall off from Cf if the pretreat method of Cf suface was not appropriate. Boron sources was ahead loaded on the surface of Cf by in situ chemical reaction to protect the fiber from corrasion of vapor such as NH_3 and increase the combination between BN film and Cf. The measured surface area of the composite fiber increased greatly to

表面的氮化硼绒膜与碳纤维的结合程度，取决于碳纤维表面预处理的方式，先期在表面通过原位化学反应引入硼源物质，形成保护膜，可以避免碳纤维在整个反应过程中受到气相侵蚀而影响氮化硼绒膜与碳纤维的结合程度，该复合材料的比表面积大幅提高，达到96m~2／g。

Further reflective type measurement can be implemented by THz-TDS. Interface information is obtained from the measured THz waveform reflected from stacked burned and normal porcine skins for simulating partial burned skin. Reflective wave from surface, interface between burned and unburned, back surface of unburned porcine had been correctively and clearly observed. Waveform and time of flight matched well with the original reflected waveform of normal and burned porcine skin.

我们进一步应用兆赫光谱技术来作样品反射式讯号的量测，可以观察到用来模拟部分烧伤的皮肤的由一层烧烫伤以及一层正常的猪皮样品堆叠成的结构中的界面，经由这个模拟结构表面以及内部界面和背面反射的讯号波形都可以正确清楚地判别，所得到反射的波形以及表面和界面间的飞行时间和个别量测正常及烧烫伤样品的结果吻合。

The standard curve of correlation between membrane surface and fluorescence intensity of FPE was obtained by acid titration. The membrane surface pH was measured according to this curve.

在不影响膜结构的条件下，利用微量TritonX－100消除膜表面与介质之间的质子浓度差，通过酸滴定实验，能够得到膜表面pH与FPE荧光强度之间的相关曲线。

Adopting 6 standard liquids surface tension values and their corresponding contact angles on top of garlic skin and garlic kernel, solid surface tension were derived as 46 and 34 for garlic skin and garlic kernel, respectively.

采用6种标准溶液之表面张力值，配合在蒜皮与蒜仁上之接触角测量，可计算推导蒜皮及蒜仁固体表面张力值分别为46 和34 。

Gloss is associated with the capacity of a surface to reflect more light in some dirctions than in others.the directions associated with mirrorreflection nor mally have the highest reflectances,measurements by this test method correlate with visual observations of surface shininess made at roughly the corresponding angles.

登录后回答可以获得积分奖励，并可以查看和管理所有的回答。登录|机器翻译的光泽与能力的一个表面，以反映更多的光线有些dirctions比others.the方向与镜子反射，也没有马利拥有最高的反射，测量了该测试方法与视觉相关的意见作出的表面shininess大致相应的角度。

The maximal depth model for single-pass milling process, the depth and surface roughness for plane surface are established. The milled profile of a single-pass milling of the jet can be modeled as a cosine curve of the form. Therefore, the maximal depth model for single-pass milling is established which indicates the quantitative relationship between the AWJ single-pass milling depth and the milling parameters.

假设磨料水射流单次铣削时的工件横截面形状为余弦曲线，建立了磨料水射流单次铣削的最大深度模型，分析了水射流压力、磨料流量、靶距、喷嘴横移速度、横向进给量和喷嘴直径及材料性能参数对单次铣削最大深度的影响规律。

The specific surface area and pore structure of mortar with cracks after electrodeposition were examined by COULTER SA3100 Surface Area and Pore Size Analyzer.

采用COULTER SA3100比表面积和孔径分析仪研究了电沉积处理后带裂缝的砂浆比表面积和孔结构的变化。

It can get the three-dimensional profile of the object surface effectively. Because of the cragginess of the three-dimensional surface when sine grating is projected the image of the sine grating is modulated and the modulated image is taken by a CCD camera with an angel compared to projecting direction. After the phase shift measuring method, the phase is gotten. Because the phase is calculated by the phase shift measuring ranges from –π to +π it isn't continuous. The phase unwrapping is necessary to recover the continuous phase about the object shape.

这种方法采用结构光照明，将正弦光栅图像投影到被测物体表面，用与投影方向成一定角度的CCD摄像机获取受物体表面面形调制的变形光栅像，根据数字相移算法计算出相位分布，由于从相移计算的相位被截断在反三角函数的主值范围内，因而是不连续的，必须通过相位展开恢复出连续相位分布，由相位－高度关系最终求出物体轮廓的三维数据信息。

Because of the cragginess of the 3-Dsurface, the distortion stripes appear when the common rectangular grating or sine grating is projected onto the object surface, which includes information about the 3-Dsurface profilometry. The images including distortion stripes are taken by CCD camera. The 2-D stripes information is got after processing these images. On the basis of mathematic reconstruction model and arithmetic , the 3-D surface profilometry data are gotten.

用普通白光将矩形光栅或者正弦光栅投影于被测物体表面上，由于物体外形凹凸等几何形状变化而在物体表面产生畸变条纹，这些畸变条纹就包含了物体表面形状的三维信息，由CCD摄像头摄取这些畸变条纹信息，对这些图像进行相应的处理，得到有关条纹中心线的二维信息，然后再根据相应的数学转换模型和重构算法对物体的轮廓进行重构，就可以得到被测物体表面的三维外形数据信息。

Comparing the electrolyte concentration shifting along the time with the membrane surface potential shifting along the electrolyte concentration, the crimple phenomenon is related to the shift rate of electrolyte concentration and to the shift range of the membrane surface potential.

通过模型计算环境中平均盐浓度随时间的变化及实验测量膜表面电位随盐浓度的改变，我们发现皱褶的出现及形变程度与盐浓度变化的急剧程度有关，也与膜表面电势变化幅度有关。

What was it that made you want to change sider ?

是什么使你临阵倒戈？

I don't know what he wants, but let's play along with him.

我不知道他要干什么，可我