查询词典 surface

The article gave empHasis to surface modification of acetate fiber, increase the specific surface area and improve the filtration of acetate filter tip through the technique of cellulase enzyme and low temperature plasma. Therefore, a new approach to reduce tar and harm of cigarette was put forward.

论文通过生物酶技术和等离子体处理技术，着重从滤嘴用醋酸纤维表面改性出发，在提高纤维比表面积的同时，可进一步提高醋酸纤维滤嘴过滤性能，从而为卷烟降焦减害提供了新途径。

According to experts, wood veneer in the production of solid wood will be cut to about 2 mm thick pieces of wood, with a special adhesive, attached to the furniture surface, and then by painting, UV baked, characterized by a smooth touch, knock on wood buckle with a finger thick plate has a sense of clarity but the irregular surface of wood, in the plate corners can be vaguely seen around 1 mm veneer.

专家介绍，实木贴面在制作中将实木切成约2毫米厚的木片，经特殊粘连，贴在家具表面，再经上漆，紫外线烘烤而成，特点为触摸光滑，用手指扣敲木板有厚实感，表面木纹清晰但不规则，在板块转角处可隐约看见1毫米左右的木皮。

On the basis of investigation into problems in the rural road surface of Liaoning Province, we simulated the shear stress between surface layer and base layer by finite element method, changed the pavement structure parameters and traffic load conditions, and found out that overloading and frequency of speed-changes in longitudinal slope driving were the main factors of forming slippage in asphalt pavement.

在对辽宁省低等级公路路面病害调查的基础上，运用有限元分析软件对基层和面层间的剪应力进行模拟计算，通过改变路面结构参数和行车荷载，得出了面层和基层层间剪应力变化的一般规律。结果重载和车速在纵坡行驶时的频繁变化是导致路面推移现象的主要因素。

Simultaneously aimed at the distribution andthe radiating surface of ceramic fire tube have studied, finally indicated: Under thesame conditions, the ceramic fire tubes radiating surface is about to the steel pipethen meets the needs.

同时针对陶火管的排布及其散热面积进行了模拟试验研究，结果表明：在配套设备都相同的情况下，陶火管的散热面积与钢管散热面积相当即可。

This limit is called the surface integral with respect to area (or the surface integral of the first type) of over and is denoted by

如果时，黎曼和的极限存在，则称此极限为在曲面上对面积的曲面积分或第一类曲面积分，记作

This is because the geometry of the surface of a globe, say, is fundamentally different from that of a flat surface.

这是因为，比方说球状表面的几何特征，与一个平坦的表面从根本上说是不一样的。

At the same time,surface mount technology required surface finishes with high level flatness.

本文着重介绍了该药水的使用工艺流程，并对该药剂的性能进行测试。

The surface appearance and hygroscopicity of ADN after coating were analyzed by SEM and weighing method. Results show that a kind of floccule of PU is formed on the surface of ADN, which makes the hygroscopicity of ADN after coating less than that before coating evidently. When coated ADN is exposed in the atmosphere for 30 days with the RH less than 60%, the hygroscopicity of coated ADN is only 0.136% and does not increase with the increasing of exposure time.

用扫描电镜和称重法分析了包覆后ADN的表面形貌和吸湿性，结果表明，聚氨酯黏合剂在ADN表面形成絮状的包覆膜，使包覆后ADN的吸湿率明显小于包覆前ADN，在相对湿度60%以下，包覆后ADN在空气中暴露30天时吸湿率仅0.136%，吸湿率不随时间增加。

The function is not good , the pump rotation rate is partial to height since device system operation is unreasonable and the pump entrance vapor erodes, that the vapor erodes , the vapor erodes the entry occurrence part in the pump the day afer tomorrow happened , is able to have air bubble in the water, that it may pound machinery on one hand seals off the outside surface soft and floury , makes it's surface damage appear on; That another aspect may make fitting that astiring sound is encircled by also contain air bubble in flow soft and floury film, can not form the stable flow film , brings about the trunk friction that fitting that astiring sound is encircled by face , makes machinery seal damage.

功能不是很好，泵转速，以高度的部分设备系统运行以来是不合理和泵入口蒸汽侵蚀，侵蚀的水汽，水汽侵蚀入境发生在泵一天afer明天发生，能够有气泡的水，它可以英镑机械密封一方面从外表面柔软，粉状，使得表面上出现的损害，这另一个方面可作出恰当的astiring声所包围也含有气泡流软和粉状电影，不能形成稳定的流动电影，带来的躯干摩擦，恰当的astiring声音所包围的脸，使机械密封损坏。

It can cut fluting on both inside and outside foam surface, and can cut irregular curved surface; it reduces distortion caused by cutting thread's thermal deformation and extends shaping category of foam product.

改变了切割泡沫的单一方式，增加了泡沫体表面的内外槽切割功能和不规则曲面切割功能。减小了切割丝热变形现象，扩展了泡沫产品的成形种类。

It is also known as one of the most poisonous naturally occurring substances.

它也被称为一个最自然发生的有毒物质。

The greatest stress is found at the location on the cross section where V is the largest.

最大应力出现在横截面上V为最大的地方。