查询词典 straight angle

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

Biomechanics of should joint at the empty out and transition moment: In the instant of leaving of the left foot, the angle between shoulder and hip was 27°, the angle of pull was 150°, the angle of axis between shoulder was -12°; In the instant of touchdown of the right foot, the angle between shoulder and hip was 72°, the angle of pull was 151°, the angle of axis between shoulder was -85°, the speed of left shoulder was 2.43 m/s, the speed of right shoulder was

腾空和过渡阶段肩关节的生物力学指标：左脚离地瞬间肩髋角度为27 ，拉引角度为150 ，肩轴角度为-12 ；右脚着地瞬间肩髋角度为72 ，拉引角度为151 ，肩轴角度为-85 ，左肩速度为2.43m／s、右肩速度为1.37m／s；左脚着地瞬间肩髋角度为58 ，拉引角度为136 ，肩轴角度为19 ，左肩速度为3.49m／s，右肩速度为1.89m／s。

Methods: 48 patients with Angle's Class II,division 2 malocclusion, 60 patients with Angle's Class II,division 1 malocclusion, as well as 15 patients with high-angle and 15 patients with low-angle facial skeletal type in Angle's Class II,division 1 malocclusion were separately compared with 50 patients with Angle's Class I who had normal profile by cephalometrics .

分别选取48例安氏II类2分类错患者、60例安氏II类1分类错患者以及各15例典型安氏II类1分类高低角骨面型患者为研究组，以选取的50例安氏I类正常面型患者为对照组。采用反映面骨关系的一般性测量项目与作者针对唇齿关系设计的测量项目进行比较分析。

One straight line guide and silk pole flat network of transmission gush out black to make network device, by the shower nozzle (2), shower nozzle shelf (1), air cylinder (7), straight line guide (8),(6) of bases, and ball silk (10) of poles and not urge at (4) of mesas job, its characterisitic is that: The stated shower nozzle shelf (1) one both ends and locate a base (11) bottom air cylinder of shower nozzle in the guide (8) connecting rod slipping of the straight line from head to foot through one, make up and lift the organization pneumatically; And this shower nozzle sets of (11) base underpart set up one group along base (6) longitudinal straight line guide (5) package that arrange again, two straight line guide packages (5)Middle shower nozzle sets of (11) base of position department set up, link with this shower nozzle of a base (11)s, and can promote their longitudinal time move the ball silk pole worked up along (6) base; The end head of this ball silk pole (10) is connecting the electrical machinery (9) of urging.

一种直线导轨和丝杆传动的平网喷墨制网装置，由喷头(2)、喷头架(1)、气缸(7)、直线导轨(8)、基座(6)、工作台面(4)及滚珠丝杆(10)和驱动电机(9)组成，其特征在于：所述喷头架(1)的两端通过一能在直线导轨(8)内上下滑动的连杆与设于喷头架底座(11)下部的气缸(7)相连，组成气动抬升机构；而该喷头架底座(11)下部又设置着一组沿基座(6)纵向排布的直线导轨组件(5)，两直线导轨组件(5)中间部位的喷头架底座(11)部设置着与该喷头架底座(11)相连、并能推动其沿基座(6)纵向来回位移动的滚珠丝杆(10)；该滚珠丝杆(10)的端头连接着驱动电机(9)。

Beginning of the main products have wide Superhard grinding straight shank end mill, grinding superhard wide keyway milling cutter straight shank, straight shank superhard grinding the whole fine-tooth milling cutter, full grinding superhard coating straight shank cutter, Super 1 / 2 shank twist drill, straight shank twist drill three categories of products.

开始的主要产品有全磨制超硬直柄立铣刀、全磨制超硬直柄键槽铣刀、全磨制超硬直柄细齿立铣刀、全磨制超硬直柄涂层立铣刀、超硬1/2柄麻花钻、直柄麻花钻等三大类产品。

"Mathematics on the corner there is an obtuse, straight angle, acute angle, right angle, the students, what angle ah?"

"数学上的角有钝角，平角，锐角，直角，同学们，还有什么角啊？"

As walk-off angle and acceptance angle of beam limit the conversion efficiency and the tunable wavelength range of difference frequency generation, research include effective nonlinear coefficient, walk-off angle and acceptance angle as functions of wavelength, the relationship between conversion efficiency and acceptance angle, and the impact of crystals length on the process of frequency conversion.

由于光束的走离角、允许角限制了转换效率和差频调谐波长范围，研究内容还涉及了有效非线性系数、走离角和允许角与波长的关系，转换效率与允许角的关系，以及晶体长度在频率变换过程中产生的影响。

Based on force diagram an analytical expression between some factors and splaying angle of the bar is brought forward, pointing out that splaying angle of the bar should be 2 3 degrees, and slitting angle should be 30 degrees approximately, outboard slant angle on the slitting groove should be 45 50 degrees and bite angle should be 7 8 degrees.

为稳定小规格带肋钢筋的三线切分轧制，对涉及棒材张开角的切分孔孔型诸角度进行了分析，通过对轧件受力状态的讨论，提出了诸因素与棒材张开角之间的解析式，指出满足三线切分稳定轧制时的棒材张开角应为 2°～ 3°，相应的孔型切分角为 30°左右，孔型外侧壁倾角应在 4 5°～ 5 0°之间，咬入角可控制在 7°～ 8°之间等。

Under the vertical load, the strength of rock mass is higher when there is only one group of joint and the dip angle is less than 20 or higher than 80; When dip angle is between 20 to 80, the strength of rock mass is much lower, it is smallest when dip angle is about 50, and it is lower when this kind of dip angle is in combination with other angle.

7在铅直向荷载作用下，岩体中只存在一组倾角小于20°或者大于80°时，岩体的强度相对较高；当岩体中存在一组节理的倾角在20°～80°间时，岩体的强度值很小，而且在与其他倾角的节理组合时，岩体的的强度值变化不太大，特别是当节理倾角为50°左右的时候，岩体的强度相对最低。

Exterior Opposite Angle Area : According to one angle area of the triangle, if we extend the two angle lines to the opposite direction, the area formed by the extending lines which like mirror area to the original angle is called here Exterior Opposite Angle Area.

外部对角映射区：针对三角形的一个角，将构成该角的两条相邻线段进行对角方向的虚线，这两条虚线围成的区域就是该三角形一个角的外部对角映射区。

Smoking cigarettes adds to the Computer Desk Computer manufacturer computer mouse Computer Computerized collar knitter machine Conduit Bodies construction board Container Bag Control Arm Cooking Thermometer general levels of air pollution as well as damaging our health.

吸烟不仅对健康有害，而且增加空气污染程度。香烟雾含有多种有害物质：不仅有致癌化学物质、有某种能阻止氧气进入血液的气体，还有引起血压增高、心速加快的被称为尼古丁的物质。

He is one of my favorite actors.

他是我最喜欢的男演员之一。