查询词典 static friction coefficient

At present, although finite element methods is a kind of effective measures in analyzing metal plastically forming problems with friction, dynamic friction in the process of metal forming is substituted with static friction and constant frictional force as one of independent constraint conditions is transposed to equivalent node-load or FEM unit is divided into contact unit and inner unit in numerous studys and applications, so that it result in relative bad accuracy and awkward operation. These defects mostly attribute to the fact that FEM bases on the variational equality principles, however frictional constraint will actually result in variational inequality energy functional.

目前，应用于分析金属塑性成形的有限元法是一种有效的处理摩擦效应的定量计算方法，但是许多应用和研究是用常摩擦来代替金属塑性成形过程中的动态摩擦；把常摩擦力作为单独的约束条件移置到等效结点载荷上或把有限元单元划分成接触单元和内单元，这些将导致解的精度相对不高及实际操作不方便等一系列问题，产生这些不足的重要原因之一在于它的理论基础是变分等式原理。

A true model of friction would include separate cases for static friction ( for a body at rest against a surface ) and kinetic friction (for a body in motion against a surface), but we will consider just one case.

那么这里的质量其实就没有那么重要了，事实上，你可以简化你的代码，假设物体的质量为1，根据牛顿第二定律使得加速度=力。

The friction characteristics of polyurethane for the friction liner of hoisting were studied. It was found that the dynamic friction coefficient of polyurethane increases with sliding velocity in the range of 0.01 to 0.4 mm/s and decreases beyond 0.4 mm/s.

本文研究了聚氨酯弹性体摩擦衬垫材料的摩擦特性，发现聚氨酯弹性体材料的动摩擦系数是和滑动速度有关的，在0.01～0.4mm/s的速度范围内，速度提高摩擦系数上升，在更高的速度下摩擦系数还会下降。

In the course of FEM model building, tensile test experiment is taken to work out the real stress-strain curve. Ring compress test is also done in this paper, through which the friction coefficient is worked out and the friction mechanism and relevant friction model for tube stagger spinning is studied. The experiments ensured the veracity and reliability of the FEM modeling.

建模过程中，通过材料拉伸试验测定了旋压材料00Ni12Cr5Mo4TiAlV时效钢的真实应力应变曲线；利用圆环镦粗试验测定了材料在不同润滑状态下的摩擦系数，并对强力旋压的摩擦性质和摩擦模型的选择进行了研究，确保了建模关键参数的准确性和可靠性。

In the paper, the friction coefficient of the friction pairs of Al2O3 matrix ceramic/45# steel during sliding experiments were studied, and the worn trace's micrographs of Al2O3 matrix ceramic were observed and analyzed, and the wear mechanism of Al2O3 matrix ceramic in dry friction and oil Iubrication were analyzed.

摘 要：本文对Al2O3基陶瓷材料/45#钢摩擦副的摩擦系数与45#钢/45#钢的摩擦系数作了对比滑动摩擦试验研究，观测分析了Al2O3基陶瓷材料磨痕形貌，并就干摩擦，油润滑状态下Al2O3基陶瓷材料的磨损机理进行了分析。

The numerical results show that: the stress distribution on contact surface is relative to the relative velocity of sliding block and friction coefficient, and the maximum relative error of stress can be 100.08%. The non-linear Stribeck friction model can better describe the real situation of contact surface, because of the consideration of impact of the relative velocity to the friction.

研究结果表明：随着接触体相对速度的改变，摩擦因数相应变化，接触面上的应力与位移的分布随之改变，应力最大相对误差达100.08%；Stribeck模型考虑了速度对摩擦因数的影响，更能描述接触的真实情况。

The influence rules between the initial pressure,spring stiffness,oblique plane angle,friction coefficient of friction pair,friction force and the characteristics of draft gear were analyzed.

分析了缓冲器的初压力、弹簧刚度、斜面角度、摩擦副间的摩擦因数以及摩擦力对缓冲器工作性能的影响规律。

The effect of the tool composition on the friction and wear behavior was investigated,and the morphologies of the rake face and rear face of the tool cutting the steel in air and nitrogen were observed on a scanning electron microscope. It was found that the Al_2O_3/TiB_2 tool was dominated by adhesive and abrasive wear in low speed dry cutting; while in high speed dry cutting,the tool was characterized by oxidation wear. An oxide layer of TiO_2 was formed by way of the oxidation of the reinforcing agent TiB_2 at a very much high cutting temperature, which contributed to greatly reducing the friction coefficient and increasing the antiwear life of the tool.Such a friction-reducing and antiwear behavior of the oxide layer was enhanced with increasing content of TiB_2 in the tool composite. However,the tool showed a relatively poorer wear resistance in N_2 than in air, because N_2 acted to retard the oxidation of the TiB_2 and the formation of the oxide layer on the tool rake face.

结果表明：低速干切削时，Al2O3/TiB2陶瓷刀具的磨损机制主要表现为粘着磨损和磨料磨损；而在高速干切削时，刀具的磨损机制主要表现为氧化磨损，刀具表面经由氧化反应生成具有润滑作用的反应膜而起到固体润滑作用，从而使刀具的耐磨性能提高，随着TiB2含量和切削速度的增加，反应膜的减摩抗磨作用增强；而在切削区通入氮气时，由于刀具表面氧化膜形成受阻，刀具的抗磨能力有所降低。

Next, in ADAMS, friction coefficient database is set up, and dialog box for defining joint friction is extended based on analyzing joint friction in mechanical system, and the method of parametric analysis is discussed for analyzing manufacture errors influence on mechanism performance.

然后，建立了受电弓虚拟样机模型，基于该模型主要研究了运动副摩擦引起的升弓轨迹和升弓扭矩的运行误差；在ADAMS环境下建立受电弓的三维参数化模型，讨论了制造误差对受电弓升弓轨迹的影响。

At the initial observation of leakage, judge on the leaking part of the foundation, and then manually set car observation, if the leakage were no significant changes in static and dynamic sealing ring has questions; such as disk when leakage can be concluded that there is significant change are moving , static friction ring problem exist; such as leakage of medium along the jet axis, the actin ring seal problem exist mostly, leakage to the surrounding medium or from the water spray cooling holes in the leakage, the many for the static seal ring failure.

在初步观察泄漏量、判断泄漏部位的基础上，再手动盘车观察，若泄漏量无明显变化则静、动环密封圈有问题；如盘车时泄漏量有明显变化则可断定是动、静环摩擦副存在问题；如泄漏介质沿轴向喷射，则动环密封圈存在问题居多，泄漏介质向四周喷射或从水冷却孔中漏出，则多为静环密封圈失效。

What was it that made you want to change sider ?

是什么使你临阵倒戈？

I don't know what he wants, but let's play along with him.

我不知道他要干什么，可我