查询词典 stack

Common Reflection Surface stack is a brand-new and special ZO imaging method, the theory of CRS stack stems from paraxial ray theory, the biggest difference between CRS stack and conventional ZO imaging method is that it consider a reflector R as a circular reflector segment Cr placed in the vinicity of reflector R, Cr can be seen as the second order approximation of the reflector. The CRS traveltime surface is the multi-coverage reflection response of the reflector mirror assigned to R.

共反射面元（CommonReflection Surface=CRS）叠加技术是一种全新的、特殊的零偏移距剖面成像方法，CRS迭加理论源于傍轴射线理论，它与普通的零偏移距剖面成像方法的最大区别是它认为地下反射层是由许多个小反射弧段互相叠合组成的，认为来自某反射点附近的一个邻域内的反射信息都可以对该反射点的成像作出贡献，因此对该反射点进行零偏移距成像时就应该聚焦更多的能量参与迭加。

Building up a stack is supposed to be a stack, and 2 is just a puny stack.

一层又一层叠加的话，2层太少了点。

Adopt girder unit and mixed unit to establish finite element model of stack based on the flexible stack. The former stack is simplified into 7 girders and 1 symmetrical space rigid frame of centralized quality.

针对某型机枪的弹性枪架，分别采用梁单元和混合单元建立枪架的有限元模型，前者的枪架被简化成由7个梁、1个集中质量组成的对称的空间刚架结构。

The second layer establish the office and reading stack and the room for discussion, the third layer establishs the reading room of Periodical and reading stack.the fourth layer establishs the electronics reading room and reading stack.

平面柱网采用：7.3%26times；5.4米，图书馆主楼为四层框架结构，图书馆一层设有图书验收、装订、编目、典藏、采编，二楼设有办公室及期刊阅览室、学生普通阅览室、教师阅览室，三层设有学生专业阅览室、外文阅览室、书库。

B the nozzle without wind question: with regard to this problem, first check the wind pump is in work, and then verify whether the increase in the stack to the correct location, in front of the stack must be of induction head stack obscured paper machine starts running, the wind began to sucker.

B。吸嘴无风题目：对于这个题目，请不后查抄风泵是否在处事，然后查抄纸堆是否跌落到侧确场所，纸堆后背的感答足务必被纸堆遮盖，板滞不休运动动纸步调时，吸嘴风才不休投递。

The steps of the mold method are as follows: the mold tool stack is closed to form the cavity; the valve is opened to allow resin to enter the cavity; the valve is closed; the resin is allowed to cool; and the mold tool stack is opened to allow removal of the plastic overcap from within the mold tool stack.

模制方法的步骤如下：关闭模制工具叠箱以形成空腔；打开阀门从而允许树脂进入空腔；关闭阀门；冷却树脂；打开模制工具叠箱从而允许从模制工具叠箱中取出塑料罐盖。

This article introduces vacuum stack preloading's developing process, reinforcement mechanism and use on soft ground treatment. Through comparative analysis among the vacuum stack preloading and other methods and instances, it shows that the vacuum preloading concerting stack preloading technology is increasingly maturing, the method is simply, and it can not only strengthen ground, but also shorten total period efficiently. It may be expanded further as a mean for highway soft ground treatment.

本文通过介绍真空堆载预压法的发展过程、加固机理以及在软基处理中的应用情况，并和其它方法进行了对比分析，通过实例说明了真空堆载联合预压法的施工工艺在公路建设中已逐渐成熟，施工方法较为简单，不仅能增加地基稳定性，同时有效地缩短施工总工期，可作为公路软基处理的一种手段进一步推广。

Through the result we know that it is lower on the firmness and higher on the rot, there is a big difference between the upper(0-40cm)and middle and floor(40-120cm)in the stack, so if controlled the height of stack about 60cm, and shorten the time in the stack ,there is a little decline on fruit rot.

另外本文还对车厢内果实的硬度和腐烂率进行了初步的研究，结果表明，随堆放位置的下降果实硬度下降，果实腐烂率则相反呈上升趋势，且车厢上层(0-40cm)与车厢中下层(40-120cm)果实的硬度和腐烂率之间有显著性差异，因此建议降低装车高度(60cm左右)，减少果实在车厢内的堆放时间，可大大降低果实的腐烂率。

Stack work, decreases in the course of off-site 10 centimeters, stack meet drive surface limit switch, stack automatically stop, under the earth trembled to centered around, at which point the Panel shows value is 0, until this process is complete, the stack can then continue to fall until the bottom.

纸堆的处事道理是，回升历程洋，离不天10公不合把握，纸堆遭受际遇传不静背的限位开关，纸堆罢手上家，自不静把握不天不静到居洋场所，此时背板表现数值因该为0，屈到这个历程达成，纸堆才可以再罢休回升屈到底部。

Stack-Based 栈基础 In many cases, compilers simply preallocate room in the function's stack area for the variable. This is the area on the stack that's right below the return address and stored base pointer.

回忆一下我们上面提到的栈结构，堆栈的下是返回地址和原堆栈指针，在大多数堆栈结构中EBP寄存器指向栈底，所以每当我们要访问某个局部变量时，我们就可以用BEP减去一个偏移量来访问某个特定的局部变量。

It is also known as one of the most poisonous naturally occurring substances.

它也被称为一个最自然发生的有毒物质。

The greatest stress is found at the location on the cross section where V is the largest.

最大应力出现在横截面上V为最大的地方。