查询词典 software component

The software is a critical component of a computerised system.

软件是计算机系统的重要组成部分。

Combined with CAD software development of grids,the design method of bolt-sphere joint is put forward based on geometry restriction and intensity restriction. The geomitry dimension of each component is determined firstly based on bolt diameter and contexture, then, maximal pull and stress of diversitied bolt are given after intensity restriction of all components is taken into acount.

在网架结构中，节点起着连接汇交杆件、传递屋面荷载和吊车荷载的作用，而网架结构属空间杆系，汇交于一个节点上的杆件至少有 6根，多的可达 1 3根，各杆件间的夹角大小不同，且节点各构件间的几何关系或强度关系相互制约，使得节点设计十分繁杂。

The model of the 2-RPS-2-UPS four freedom parallel robots was established,and the movement simulation of the assigned path was performed by using the ADAMS software.The coordinate curve of the execution component in the rate process was obtained.

运用ADAMS软件建立了2-RPS-2-UPS四自由度并联机器人的模型，并进行了给定轨迹的运动仿真，得到了运动过程中执行构件的运动轨迹坐标值曲线。

Last, this paper discusses some correlated problems of component-based software configuration management technology.

最后，本文讨论了基于构件的软件配置管理技术的一些相关问题。

The magnetism dipole theory was used to analyze the demagnetization field of the component, and computer simulation was processed with software Matlab.

采用磁偶极子理论对该零件的退磁场分布进行了分析，应用Matlab软件进行了计算机仿真，通过仿真使零件各关键部位的退磁场分布得到直观显现。

Developing component is a software design process, in which the common function modules are derived from the system functions and the modules are designed and realized with common interface.

开发组件主要是把系统的某些功能抽象为具有通用接口的功能模块，以组件的方式设计并实现这些功能模块。

A set of automatic testing and fault diagnosis system for a certain control and change component is introduced. The realizing technique of hardware and software for automatic testing is discussed.

介绍了某控制转换装置测试仪的自动测试和故障诊断的设计思想，讨论了测试仪的硬软件设计中如何实现自动测试，以及利用FAN算法来计算故障定位测试向量的故障诊断思想和方法。

A modeling layer method of software architecture and the component-based graphical modeling method are proposed in DRSCDE.

提出软件架构的建模层次，研究了DRSCDE基于构件设计的图形化建模方法。

By using CFD software FLUENT,numerical simulation for the three-dimensional flow of air between honeycombed plate heat transfer component s is carried out.

应用CFD软件FLUENT对蜂窝板传热元件板间空气的三维流动进行了数值模拟。对中心间距为19 mm的蜂窝板传热元件在不同质量流量情况下的换热和阻力特性进行了计算分析，给出了在300

Taken the three dimensional shining metal combination machine tool as an object of study in the paper,the main structure and motion form have been discussed and the work process and control requirement of machine tool have been analyzed,the movement cycle diagram of machine tool and the motion table of hydraulic pressure component have been given.Then the control system design based on PLC has been proposed,the I/O address table has been listed and the hardware and software of the control system has been de...

文章以三面铣组合机床为研究对象，通过对主要结构和运动形式的探究以及对机床的工作过程和控制要求分析，给出了机床动作循环图、液压元件动作表；并采用PLC控制系统的设计方法，列出了I/O地址分配表，进行了软硬件设计，绘制了 PLC的外部接线图和单循环自动工作流程图及其说明；实验运行结果表明，将PLC技术应用于三面铣组合机床具有整体技术及经济效益。

On closer examination, though, this is not a vote for multilateralism but just the opposite.

仔细审视后我们发现，这并非是对多边主义投出的赞成票，而是恰好相反。

Uncovering their weak spots, so I can defeat them.

揭露出他们的弱点，这样我就可以打败他们了。