查询词典 seam weld

The residual stress distribution of the tangential residual stress,the hoop residual stress and the normal residual stress test of spiral seam arc weld pipe were studied on the basis of elastic mechanics analysis and superposition theorem.

基于弹性力学应力分析和叠加原理，研究了螺旋缝埋弧焊管切环法残余应力测试中的残余应力分布。

In the welding process,it is very important for welding torch automatically tracking the weld seam to assure welding quality and improve welding automation level.

焊接过程中焊炬自动跟踪焊缝对保证焊接质量，提高自动化程度有着极其重要的实际意义。

Since the welding torch pose has an important effect on the quality and appearance of weld seam, the optimization of welding torch pose fo...

鉴于焊炬姿态是影响弧焊质量和焊缝成形的一个重要因素，本论文对弧焊机器人空间全位置焊接条件下焊炬姿态的优化进行了系统的研究。

When the Al-Mg-Zr-Sc welding wire was used as filling material, the grains of welding seam were refined obviously, and the weld joint was greatly strengthened by forming of fine equiaxial grains layer in fusion zone.

结果表明：采用两种焊丝焊接的Al-Mg-Sc合金薄板的焊接接头强度系数均大于0.9。

When the Al-Mg-Zr-Sc welding wire was used as filling material,the grains of welding seam were refined obviously,and the weld joint was greatly strengthened by forming of fine equiaxial grains layer in fusion zone .

但采用Al-Mg-Zr-Sc合金焊丝为填充材料时，焊缝晶粒组织明显细化，熔合区形成的细小等轴晶层提高了基材与焊缝填充材料的结合力，焊接接头的屈服强度比采用Al-Mg-Zr合金焊丝为填充材料时提高了100 MPa，显著提高了Al-Mg-Sc合金焊接构件的许用强度，因此焊接Al-Mg-Sc板材更宜采用Al-Mg-Sc-Zr焊丝。

Mm. 7.5.3 Requirements for quality of weld joint's surface: a No crack, not fusional, bubble, slag, splash; b Surface of seam of pipeline with design temperature lower than -29℃, stainless steel pipeline and alloy steel pipeline with trend of harden quenching shall be free from undercut.

The surface shall be smooth 7.5.3 焊接接头表面的质量应符合下列要求： 28 SH 3501-2002 a 不得有裂纹，未熔合，气孔，夹渣，飞溅存在； b设计温度低于-29℃的管道，不锈钢和淬硬倾向较大的合金钢管道焊缝表面，不得有咬边现象；其他材质管道焊缝咬边深度不应大于 0.5mm，连续咬边长度不应大于 100mm，且焊缝两侧咬边总长不大于该焊缝全长的 10%； c 焊缝表面不得低于管道表面，焊缝余高Δh 应符合下列要求： 1 100%射线检测焊接接头，其Δh≤1+0.2b1，且不大于 2mm； 2 其余的焊接接头，Δh≤1+0.2b1，且不大于 3mm。

In CO2 gas metal arc welding, the difficulty hi seam tracking by pendular arc sensor is how to attain the tolerance signal of weld joint.

在CO_2气体保护焊中，采用摆动电弧传感器进行焊缝跟踪的困难在于如何提取准确的焊缝偏差信号。

An intelligent controller was designed for welding process charactering as multivariable and non-linear to realize dynamic control for seam tracking and weld penetration control .

研究了从焊接温度场中获取焊缝位置和熔透信息的方法，在此基础上设计了规则自调整模糊控制器，实现了MIG/MAG的焊缝跟踪与熔透控制。

The image acquisition of weld seam is influenced by the intense spatters combusting gas, arc and the noise.

获取的图像中存在大量的飞溅、烟尘、电弧光以及周围环境电磁、静电产生的噪声干扰。

These tubular sections are constructed from plate rolled into cylindrical shapes with a submerged arc weld forming the long-seam.

这些管状路段建成后，由钢板卷成圆筒形状，以埋弧焊形成长缝。

He and Nina moved to California and lived at 2005 Ivar Street, Apt.

他和Nina搬到加州，并在2005年伊瓦尔街，公寓生活。

Droperidol （ potently inhibits transfected HERGchannels and this is the probable mechanism for QT prolongation.

氟哌利多有效地抑制了转染的 HERG 钾通道，可能是 QT 间期延长的机制。