查询词典 rigidity

As a structure that is compressed and bended, with increasing of the span, length slender ratio and carrying load of arch increase, lateral rigidity and width span ratio of arch ring minish relatively. During constructing and bring to bear, lateral stability becomes especially severity and a control factor of arch bridge design.

拱作为压弯结构，随着跨径的增大，杆件的长细比及所承受的荷载也随之增大，拱圈横向刚度、宽跨比相对减小，在施工阶段及使用阶段横向稳定问题特别突出，常常成为拱桥设计的控制因素。

And in this process the torsional rigidity of the cross axle type universal shaft was found having great impacts on the torsional vibration of the main transmission system.

在进行轧机主传动系统的扭振分析时，发现十字轴式万向联轴器的扭转刚度对主传动系统扭振的影响十分巨大。

Based on this discovery this dissertation presented that the torsion rigidity of the cross axle type universal shaft must be taken into account when researching the main transmission system of the rolling mill.

并依此提出了在研究轧机主传动系统的扭转振动时，必须计及十字轴式万向联轴器的扭转刚度的观点。

The torsional distortion and the torsional rigidity of the cross axle type universal shaft are calculated by using the three-dimensional finite elements method.

运用三维有限单元法对十字轴式万向联轴器的扭转变形和扭转刚度进行了分析计算。

After the rigidity matrix calculations, the FEM analysis program ANSYS is used to create models, with the truss structure and box cross-sectioned cantilever board beam as models.

在完成结构刚度矩阵计算的前提下，以桁架结构和矩形截面悬臂板为模型，利用有限元程序ANSYS进行建模，分析了不同类型的结构在温度变化作用下的响应，从而得知温度变化对桁架结构的模态参数影响不大，而对矩形截面悬臂板梁的模态参数有一定的影响。

In construction design, there is still no a reasonable uniform cost about the rigidity amplification coefficient of center beam and boundary beam.

在结构设计中，选择一个合理的中梁、边梁刚度放大系数和选择一个合理的梁端弯矩调幅系数一直没有得到一个统一的值。

This structure has advantages of simple manufacture craft and good supporting rigidity of main gear box bearing.

该结构的桥壳制造工艺简单、主减速器轴承支承刚度好。

The slide block contains 4 ball circuits which deliver high load capacity, high rigidity and high accuracy.

滑块4列回球路提供高承载，高刚度和精度高。

A rear body brace has been added to the area previously occupied by the soft top, resulting in additional rigidity.

甲后车身支架已被添加到以前软顶占领了该地区，造成额外的刚性。

An aluminium radio plate X bracket also comes as standard, that not only looks great but also helps increase rigidity of the car, while finally, to ensure the engine mounting points are kept aligned, reducing stress on the crankcase, the 720-08 is supplied with the single piece orange anodised engine mount.

一铝电台板x托架也作为标准，即不仅看起来很大，但也有利于增加刚度的汽车，而最后，为确保发动机安装点是保持不结盟，减少压力对曲轴箱， 720-08供应与单件橙色电镀引擎挂载。

I hope that this success is just the first in a long series.

我希望这只是成功的开始。

Three dimensional stresses on the interface of tire and soil, tire deflection and soil sinkage are measured.

测试轮胎——沙土界面上的三向应力、轮胎变形和沙土沉陷；建立考虑剪切应力对沙土承载特性产生影响的车轮牵引性能预测模型；分析车轮作用下土壤的纵向稳定性。