查询词典 real depth

At 135 mm depth and 0.28 m/sec speed, the biomimetic furrow opener surface with UHMWPE tubular ridges recorded 0.62 kN and 0.17 kW, while at 135 mm depth and 0.92 m/sec speed, the values were 0.91 kN and 0.82 kW. The experimental values of resistance force and power for the conventional surface furrow opener at 100 mm depth, and 0.28 m/sec speed were 0.72 kN and 0.20 kW, while at 100 mm depth and 0.92 m/sec speed, the values were 1.11 kN and 1.0 kW. At 135 mm depth and 0.28 m/sec speed, the conventional surface furrow opener recorded 0.93 kN and 0.25 kW, while at 135 mm depth and 0.92 m/sec speed, the values were 1.50 kN and 1.35 kW.

试验测试结果：当耕深100 mm和耕作速度0.28 m/sec时，实测的普通开沟器的土壤阻力和动力消耗分别为0.72kN和0.20kW；当耕深100 mm和耕作速度0.92 m/sec时，实测的普通开沟器的土壤阻力和动力消耗分别为1.11kN 和1.0kW；当耕深135 mm和耕作速度0.28 m/sec时，实测的普通开沟器的土壤阻力和动力消耗分别为0.93kN和0.25kW；而当耕深135 mm和耕作速度0.92 m/sec时，实测的普通表面开沟器的土壤阻力和动力消耗分别为1.5kN和1.35kW。

The phosphorus forms and BAP vary with horizontal and vertical positions. The total phosphorus, inorganic phosphorus, BAY, and iron-phosphorus contents were high at a depth of 0~20 cm at the first sampling point, and then decreased at 20-40 cm of depth. This shows that the potential release capacity of P at 0-20 cm of depth is higher. The concentrations of total phosphorus and inorganic phosphorus decreased at 0~20 cm of depth and increased at 20~40 cm of depth at the second sampling point, but BAY and Fe-P increased along with the depth consistently. This shows that the deeper layer at the second sampling point had a higher potential release capacity of phosphorus.

不同地点沉积物各磷形态和BAP的垂向变化有较大的差异。1号采样点的总磷、无机磷、铁磷和BAP质量比在沉积0~20 cm处较高，20~40 cm逐渐减小，说明0~20 cm内释磷潜力较大；2号采样点的总磷和无机磷质量比先减小，20~40 cm逐渐增加，而BAP和铁磷质量比随深度增加呈上升趋势，说明2点深层具有较大的释磷潜力。

According to some bad phenomenon about real estate investment, real estate supply, real estate price, the property management and the real estate finance of western China, the thesis study these bad phenomenon respectively through a great deal of statistical data and statistical method, and then the thesis find out the widespread problem of real estate investment, real estate supply, real estate price, the property management and the real estate finance of western China. According to the actual circumstance that the real estate industry of the western China, the thesis put forward the countermeasures that solve these problems above and guide the real estate industry of western China progress healthily. Levy upon ground and housebreaking is one factor that produces inharmonic society.

根据西部地区房地产投资、房地产供求、房地产价格、房地产物业管理和房地产金融等方面表现出的一些不良现象，通过大量的统计数据并采取相关的统计方法对西部地区房地产业发展过程中表现出的这些现象分别进行分析，结合西部地区房地产业发展的实际情况，本文揭示出房地产业发展中房地产投资、房地产供求、房地产价格、房地产物业管理和房地产金融这五个方面在西部地区均具有的普遍性问题，并针对具体的问题提出了相应的对策，以指导西部地区房地产业健康持续发展。

The predicted values of resistance force and power for the conventional surface furrow opener at 100 mm depth and 0.28 m/sec speed were0.51 kN and0.14kW, while at 100 mm depth and 0.92 m/sec the values were0.98kN and0.88kW. At 135 mm depth and 0.28 m/sec speed, the conventional surface furrow opener recorded 0.70 kN and 0.20 kW, while at 135 mm and 0.92 m/sec speed, the values were 1.40 kN and 1.26 kW. The predicted values of resistance force and power for the biomimetic furrow opener surface with UHMWPE tubular section ridges at 100 mm depth and 0.28 m/sec speed were 0.45 kN and 0.12kW, while at 100 mm depth and 0.92 m/sec speed, the values were 0.73kN and 0.66 kW.

对于超高分子量聚乙烯材料仿生脊型非光滑结构表面，当耕深100 mm和耕作速度0.28 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.45kN和0.12kW；当耕深100 mm和耕作速度0.92 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.73kN和0.66kW；当耕深135 mm和耕作速度0.28 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.62kN和0.17kW；而当耕深135 mm和耕作速度0.92 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.91kN和0.82kW。

Therefore, it can be regarded as a great improvement of the investment decision-making theory and methods .This article makes a systematic research on real options theory and method and its application, including the following several main aspects:Firstly, it makes a detailed discussion about the common theoretical basis of financial options and real options, including no-arbitrage equilibrium principle, risk-neutral definition, complete market and dynamic tracking.Secondly, it analyze three basic characteristic of investment decision-making in modern market economic system: irreversibility, uncertainty and flexibility, and from the angle of their mutual quantitative and qualitative interactions, it makes a comparison between the traditional NPV methods and real options methods and makes a summary of the general analytical methods of real options.Thirdly, it discusses the all elements in the application of real options such as the ^leakages in value of real assets, basis risk, and private risk, and furthermore, it attempts to put forth a normalized strategy of its application and construct a basic framework of its application.Fourthly, it applies real options theory to strategetic investment of enterprises and the buy-out of company, putting forth a value model for strategetic investment program and making a concrete analysis of its application to buy-out. Furthermore, it advocates that a flexible investment decision-making system should be setup according to real options theory in our country.

本文对实物期权理论和方法及其应用进行了系统研究，主要内容包括如下几个方面：(1)详细讨论了金融期权和实物期权共同的理论基础，主要包括无套利均衡原理、风险中性定义、完全市场以及动态复制方法，对这些理论方法的探讨既是本文的出发点和基础，它们提供了研究实际应用实物期权的一个基准点，也是贯穿全文的线索和灵魂；(2)分析了现代市场经济体系中投资决策的三个基本特征即不可逆性、不确定性和时机选择，并从它们数量上和质量上相互作用的重要意义的角度，分析了传统的净现值法与实物期权方法的差异，指出了净现值法在不确定环境中存在的缺陷及实物期权处理投资灵活性的价值，并将净现值法纳入实物期权投资分析决策体系当中，总结了企业投资决策实物期权的一般分析方法；(3)探讨了实物期权应用中要考虑的各种要素，如实物资产的价值漏损、基差风险和非市场风险等，并进一步提出了实物期权应用的规范化策略和构建了一个实际应用实物期权方法的基本框架，尝试将期权的基本原理与企业在现实经济环境中投资决策的要素结合起来，从而可以在一定程度上超越期权的复杂的数学计算而汲取期权思想的精华，从而促进期权决策方法在实际投资决策中的应用；(4)将实物期权方法应用于企业战略投资，得出了战略投资项目的价值模型，指出可以将实物期权理论和方法应用于企业并购，分析了应用的具体方面，并提出应根据实物期权理论建立一套适合我国企业的灵活的投资决策系统。

Construction Bank of China Assistant Governor Chen Zoff, the Ministry of Construction Housing Industrialization Promotion Center童悦Chung, deputy director of the CBRC, deputy director of the Department policies and regulations Huang visited the venue and said congratulations, Ministry of Land and Resources Land Use Division Hongzhi, deputy director of the cold, the Ministry of Construction Policy Research Center, deputy director Wang Jue Lin, China Association of Mayors Vice President and Secretary General Tao Siliang, China's Real Estate Association, vice president and secretary general顾云昌, Beijing University of Economics and Management, Associate Dean Cao peace, Beijing International Trust and Investment Corporation board chairman and general manager Wang Xiaolong,今典集团chairman张宝全, Yu Fat Dawnrays Beijing real estate company chairman Zhang Jidong, Chongqing International Trust and Investment Corporation, president of Assistant Sun Fei, China Construction Bank real estate financial services such as general manager Liu Tiemin authority has on China's real estate financial innovation, as well as real estate and urban development of the interactive relations between the in-depth discussion of the Chinese real estate finance and urban sustainable development put forward a series of forward-looking perspective.

中国建设银行副行长陈佐夫，建设部住宅产业化促进中心童悦仲副主任银监会副主任，新闻部的政策和法规黄参观了展馆，并表示祝贺，国土资源部土地利用和资源司宏志，副主任冷，建设部政策研究中心副主任王珏林，中国市长协会副会长兼秘书长陶斯亮，中国房地产业协会副会长兼秘书长顾云昌，北京工业大学经济管理学院副院长曹和平，北京国际信托投资公司董事长，总经理王小龙，今典集团董事长张宝全，北京于发东瑞房地产公司董事长章机洞，重庆国际信托投资公司总裁助理孙飞，中国建设银行房地产金融服务，如总经理刘铁民管理局已对中国的房地产金融创新，以及房地产和城市发展的互动关系深入讨论中国房地产金融和城市的可持续发展提出了一系列前瞻性的观点。

The maximal depth model for single-pass milling process, the depth and surface roughness for plane surface are established. The milled profile of a single-pass milling of the jet can be modeled as a cosine curve of the form. Therefore, the maximal depth model for single-pass milling is established which indicates the quantitative relationship between the AWJ single-pass milling depth and the milling parameters.

假设磨料水射流单次铣削时的工件横截面形状为余弦曲线，建立了磨料水射流单次铣削的最大深度模型，分析了水射流压力、磨料流量、靶距、喷嘴横移速度、横向进给量和喷嘴直径及材料性能参数对单次铣削最大深度的影响规律。

The results indicate that multiple reflections are favorable to the increase of depth. When the focal position is above the surface, the absorptive intensity on the front decreases, so the cutting depth decreases. When the focal position is below the surface, the position on the front with the maximum power intensity is downward. The intensity distribution is toward the deeper position, the cutting depth increases. But if the negative focal distance is extremely big, the intensity of the deeper position attenuates sharply with the increase of focal radius and light distances, so the depth deceases.

正离焦切割时，前沿吸收的总激光功率密度减小，切割深度减小；负离焦切割时，最大激光功率密度值的位置下移，使得前沿功率密度分布朝着深部推进，切割深度增加，若负离焦量过大，表面光斑直径和光程增加，更深位置的功率密度减小，切割深度减小；随着激光功率增加、切割速度减小，则前沿弯曲程度减小，被激光直接照射的前沿部位增长，前沿吸收激光功率密度增加，切割深度增加。

In this paper, Newton iteration formula for computing normal depth and critical depth was put forward by mathematical transformation of uniform flow equation and critical flow equation of circular section tunnel. Then, the relationship between the corresponding central angle and the introduced parameters was analyzed. An approximate formula for angle was obtained according to optimal uniform approximation principle. Using this approximate formula as initial value of iteration formula, a direct formula for calculating normal depth and critical depth of circular section tunnel was established after its first iterative.

该文通过对圆形断面均匀流方程与临界流方程的数学变换，分别得到其正常水深与临界水深的牛顿迭代公式，同时，通过对正常水深与临界水深对应的中心角与引入参数之间关系的分析及数值计算，利用最优一致逼近原理分别得到了正常水深与临界水深对应中心角的近似计算式，并以此近似计算式为初值，用迭代方程进行一次迭代得到了圆形断面均匀流水深与临界流水深的直接计算公式。

To analyze the pseudo phenomena caused by migration velocity error, the paper firstly studied the depth error between post-stack migration and prestack migration caused by same velocity error, and found the depth error was only relative to velocity error and had no direct matter with methods of depth migration (post-stack migration or prestack migration). Then the paper did numerical simulation of a complex lenticular body model with wave-equation modeling and migration, and found that the velocity error could not only induce depth error, but also could change the modality of construction and the event of subjacent layers. Furthermore, it could change the frequency of reflective event. They are the pseudo phenomena caused by migration.

从分析偏移速度误差带来的各种假象出发，本文首先对比分析了速度误差对叠后深度偏移和叠前深度偏移的影响，发现偏移剖面的深度误差仅与速度模型的误差有关系，与具体的偏移方法没有直接的关系；然后对一个复杂的透镜体模型进行了波动方程叠后正演和偏移计算，详细地讨论了不同的速度误差带来的各种假象，发现速度误差不仅会带来深度误差，而且会造成构造体的形态变化，下覆地层同向轴的扭曲，还可能引起地层同向轴的频率发生变化，给资料解释带来一定的假象。

If you were not , and OS X just booted normally, have no fear.

如果你没有，和OS X刚刚启动通常，没有恐惧。

I only want to preserve our all .

我只想保存好我们的一切