查询词典 range angle

The pit shaft parameters of the elevation angle,the azimuth angle,the tool of facial angle and so on are obtained after the computation.

陀螺测斜技术以动力调谐速率，陀螺测量地球自转角速率分量和石英加速计测量地球加速度分量为基础，经计算得出井筒的倾斜角、方位角、工具面角等参数。

Profile angle, soft facial angle,Z angle and lower facial height were increased significantly after treatment and the prominence of upper and lower lip were decreased significantly after treatment.

结果：18例患者治疗结束后软组织侧貌改善明显，侧面角、软组织面角和Z角，以及下面高显著增大；上、下唇凸度显著减小。

This Digital Compass not only provides the course angle but also affords the carrier s pitch angle and roll angle .The two data of attitude are both exported digitally.

本次设计的这种数字航向仪除了提供载体的航向角，还提供了载体俯仰角和翻滚角两个姿态量，并以数字形式输出。

During the lateral parabolic profile was computed,numerical methods of calculating angle of inclination on initial point of the lateral paracurve and calculating angle of inclination based on interval length were analyzed.It is pointed out that the key of the lateral parabolic profile design is a circular function equation which can be applied to solving the angle of inclination on initial point of the lateral paracurve.

对侧位抛物线剖面设计求解过程中的求侧位抛物线初始点井斜角的数值方法和从段长求井斜角的数值方法进行了分析，指出其关键是求解侧位抛物线初始点井斜角所满足的一个三角函数方程。

Based on the definition of benchmark angle and compensation angle,the algorithm of roll angle of projectile in fire plane is brought out and the calculating error is analyzed.The simulation is carried out for the swing of projectile and the measurement of geomagnetic signal error.

将弹丸的滚转角分解为基准角和补偿角，给出了处于射击平面内的弹丸滚转角解算方法并进行了误差分析，针对弹丸的摆动及地磁信号测量误差进行了仿真。

Then, aerodynamic parameters in different flight conditions are used to imitate the uncertainty of the system, and the digital simulation of closed-loop system designed is performed. The results show that the system can accomplish asymptotic decoupling of roll angle, sideslip angle and head-on angle for aircraft, and the system is provided with the function for restraining uncertainty in the system. This illustrates that the flight control system designed has not only good decoupling characteristic, but also better robustness.

然后用不同飞行条件下的空气动力参数变化来模拟系统的不确定性，并进行闭环系统数字仿真，结果表明，所设计的控制律不仅可实现对飞机滚转角、侧滑角、迎角等的渐近解耦控制，而且对系统不确定性具有较强的抑制作用，说明系统具有较好的解耦性和较强的鲁棒性。

The system can automatically seek north when the vehicle is immobile. And the time consumption is no more than 5.5 min. Besides, the system can keep azimuth angle and provide tilt angle and pitch angle of the vehicle.

本系统可以在车载条件下，停车完成自动寻北，寻北时间小于 5.5min；本系统还具有在机动时进行方位保持、实时提供载体倾斜角和俯仰角等功能。

Firstly, the control of reentry phase and the model of RCS jets are presented. Then the flight control system is divided into two subsystems based on the time-scale separation principle. The fast states subsystem corresponds to the three body-axis angular rates, the slow states subsystem controls the angle-of-attack, sideslip angle and the rate of the bank angle about the velocity vector. Lastly, the proportional-plus-integral feedback is designed to increase the system robustness.

首先，分析了SRLV再入段的数学模型，并给出了反作用推力控制系统的控制模型；其次，将非线性动态逆方法与时标分离原则相结合，考虑飞行器姿态控制系统的外环角回路的慢变特性和内环角速度回路的快变特性，独立设计了两个回路的控制律；最后，为了增强系统的鲁棒性，分别在两个回路中引入了比例－积分反馈，有效地抑制了干扰力、力矩和非线性对消带来的逆误差。

A large range of IRZ and intense fluctuating velocity area around the boundary of IRZ is measured and thought to be important to keep the excellent ignition and combustion characters of the new kind swirl burner. Together with temperature trace method, different structure and operation parameter of the burner are studied in this paper about their effects on turbulent and mixing characters of swirling jet. The structure variation includes different blade angle, use of central gear shape baffle, variable outer length and angle of lean primary air outlet, use of wedge outlet of lean primary air.

采用上述两种测量方法并结合热质比拟温度示踪的方法，本文对径向浓淡旋流煤粉燃烧器喷口结构和气流流动参数的变化对旋流流场的流动、混合、湍流脉动特性的影响进行了深入研究，研究了旋流叶片倾角大小、中心齿型扩锥、淡一次风扩口外伸长度和扩角的变化、淡一次风楔形扩口、直流二次风扩口角度的变化对出口旋转射流流动特性的影响，研究了一次风率和旋流二次风率运行参数变化的影响规律。

The results show that the surface roughness decreases with increase of the inclination angles within the range of 10° to 30°. After the angle approaches to 30°, increase of the inclination angle causes increase of the surface roughness. Furthermore, the effect of inclination angles on cutting speed was investigated.

研究结果表明：工件倾角的大小对已加工表面粗糙度有明显的影响，在倾角为10°～30°时，表面粗糙度随着工件倾角的增大而降低；此后，随着倾角的进一步增加，表面粗糙度有所升高。

"The operators will suffer a temporary decrease in the number of consumers and short message services as people may not like having to provide their ID cards for a phone number," Xu Junqi, vice-dean with the Policy-Making Institute of the Telecommunications Research Centre under MII, said yesterday.

信息产业部下属的通信决策研究院副主任徐俊其昨天说：&实行手机实名制后，人们可能不太情愿用身份证注册手机号，所以通信运营商会暂时面临用户减少和短信用户减少的问题。&

I don't believe in make-believe!

我不相信这些虚构的故事。