查询词典 optimal process

Based on the optimal filters, various recursive algorithms of the optimal smoothing estimation under white-noise condition are derived, and problems of reducing storage requirements and computational load for the fixed-interval smoothers are discussed, moreover, optimal smoothers under various noise conditions are proposed, thus, the optimal state smoothing theory is founded.

在最优滤波算法的基础上，本文推导出白噪声情形下的状态最优平滑估计的各种递推算法，讨论了减少固定域平滑的存贮空间和提高运算速度问题，并提出了在多种噪声条件下的平滑估计方法，从而建立了这类系统的状态最优平滑估计理论。

The constraint conditions of quasi optimal and strict optimal OOCs constructed by recursive method are theoretic analyzed. Based on these constraint conditions, as the initial conditions of OOCs obtained by direct construction, some quasi optimal and strict optimal OOCs with larger code length and sizes are obtained by recursive method.

2理论研究了基于递归法构造准最佳和严格最佳光正交码的约束条件，在此基础上，以直接构造法得到的光正交码为初始条件，利用递归法构造了一些具有相同相关特性的码长更长、容量更大的准最佳和严格最佳光正交码。

The optimal entrance point mostly locate at the root of accessoryprocess which adjacent to the mamillary process from L1 to L4, Theadjustable range of entrance points of the 4 segments almost cover theaccessory process, But at L5, The optimal entrance point is much moreoutside away from the accessory process, just at the middle of thetransverse process and the adjustable range of entrance points islimited.

这与钉尾间距的明显变化相一致，手术时应注意调整螺钉钉尖内偏角度观察椎弓根螺钉进钉点发现内外侧螺钉进钉点与内上、外上螺钉进钉点构成接近矩形的梯形区域，最佳进钉点居于内外进钉点中部。L1到L4最佳进钉点位于副突根部靠近乳突处，随着椎体节段下降，进钉点逐渐移向外侧，L1最佳进钉点基本在副突根部骨嵴内侧缘，L2、L3最佳进钉点基本在副突根部骨嵴上，L4最佳进钉点基本在副突根部骨嵴外侧缘。L1到L4可选进钉点范围几乎均包含副突骨嵴。L5最佳进钉点则明显偏外，多数位于副突根部与横突外端连线的中内1／3。

By simulation, the optimal operation conditions were gained in every step in the separation process, and polymerization-class isoprene was gained by the process. And to improve the economy of process, the process was studied by simulation, 99% cyclopentene and 1, 3-pentadiene were gained by continuous separation process. All were the base of the process industrialization.

通过模拟研究，得到分离各步的最佳塔高，进料位置和各种操作条件；并进行了全流程的模拟优化得到聚合级的异戊二烯的各种工艺参数；通过模拟研究对分离工艺进一步深化，得到了从C5中分离出环戊烯和间戊二烯的优化工艺条件，对工艺经济性进一步优化，给过程工业化提供了依据。

In this paper, two assemblies of special test equipments have been designed and fabricated by authors in our laboratory: namely Catalyst Molding Process Analyzer and Catalyst Mechanical Process Tester. These new skills are developed for the dynamic studies on whole mold forming process and crushing process of Fe-Cr WGHS catalyst pellet. Based on the orthogonal experimental design, the effects of some factors during the forming process of solid catalyst, such as predensification proportion, calcination time, calcination temperature and content of graphite on the mechanical strength of catalyst pellets are systematically examined, and the molding conditions have been optimized. Based on the experimental data, the relationship between catalyst density and forming pressure are educed, and the physical significances of some related parameters are described. The parameter of macro scopic elastic moduls has been suggested to character the mechanical properties of molding catalyst. The effects of molding pressure on mechanical properties of catalyst pellets are discussed, and results show that there exists a optimal molding pressure for the ideal mechanical properties: when over-high or over-low pressure is applied, the specific surface area and side crushing strength of catalyst pellets will decreased. The "rebound effect" will be undermined by the unsuitable pressure maintain process, resulting in the apparent decrease of mechanical strength of catalyst pellets.

本研究通过自行设计制造的催化剂模压成型过程分析仪（Catalyst Molding Process Analyzer， CMPA）和催化剂力学性质测试仪（Catalyst Mechanical Properties Tester， CMPT），以Fe-Cr系高温变换催化剂片剂为研究对象，对成型过程和受压破碎过程提供了全过程动态研究的新手段；本研究利用正交实验设计方法考察了固体催化剂成型过程中诸因素（包含预密致比例、煅烧时间、煅烧温度和石墨含量等）对催化剂成型体强度的影响，并对成型条件进行了优化；根据实验结果，关联确定了固体催化剂成型过程中的密度－压力关系式，并对方程中诸因子的物理意义进行了描述；提出了一种利用宏观弹性模量来表征成型催化剂的力学性质的方法；研究讨论了成型压力对催化剂成型体强度性质的影响，结果表明：对于催化剂成型体的强度和比表面性质，成型压力存在着一个最佳值，过高的成型压力会导致比表面积和侧压强度的降低；不适当的成型压力的维持时间会破坏&压力回弹&作用，造成催化剂成型体的机械强度明显降低。

The static model of torsion joint is based on that of bending joint. The effects of structure parameters inside air pressure, initial angle, rube average radius, rube shell thickness on the turning angle are analyzed and the following conclusions are drawn: the relationship between the angle of torsion joint and the inside air pressure is basically linear, the angle of torsion joint increases with the initial angle and rube average radius, the angle of torsion joint decreases while the rube shell thickness increases. The kinetic equation is built for torsion joint. Simulating experiment implies that the time of inflating and deflating process is extremely shorter than that of kinetic process. So the pneumatic process can be ignored in actual system design and control. The factors that affect the dynamic features of torsion joint, such as shell thickness of rubber tube, average radius, initial angle, connector's outlet area, moment of inertia and viscous damping coefficient, are analyzed and the following conclusions are drawn: the change of rube shell thickness has no effects on the dynamic process of FPA inside air pressure while greatly affects the turning angle of torsion joint; when the rube shell thickness is small, the torsion joint has a bigger turning angle, no overshoot and long risetime, when the shell thickness is big, the turning angle of torsion joint is small, but has high response speed, overshoot and low shock; when the rube average radius increases, the turning angle of torsion joint increases and the overshoot increases too; when the initial angle of torsion joint is big, the turning joint is big, the overshoot is small and shock is low, but the risetime is big; the connector's outlet area affects the dynamic process of FPA inside air pressure greatly, but has no effects on the dynamic process of turning angle; moment of inertia and viscous damping coefficient have no effects on the dynamic process of FPA inside air pressure, but affect the dynamic process of turning angle greatly.

在弯曲关节模型推导的基础上，建立扭转关节的静态模型，并分析了扭转关节内腔压力，初始转角，橡胶管平均半径，橡胶管壁厚等参数对关节转角的影响，得出扭转关节的转动角度与充入FPA内腔的压缩气体压力之间基本呈线性关系，扭转关节的转角随初始角度和橡胶管平均半径的增大而增大，扭转关节的转角随橡胶管壁厚的增大而减小的结论；建立了扭转关节的动力学方程，仿真实验表明FPA的充放气过程与扭转关节的动力学过程相比时间极短，在实际系统设计和控制过程中可以忽略不计；分析讨论橡胶管壁厚，平均半径，初始角度，气体节流口面积，转动惯量，粘性阻尼系数等因素对扭转关节动态特性的影响，得出橡胶管初始壁厚的变化对扭转关节FPA内腔压力的动态响应几乎没有影响而对关节转角的响应曲线影响比较明显，壁厚较小时，关节可以得到较大的转角，并且转角的响应曲线没有超调，但上升时间长，壁厚较大时，关节转角变小，响应加快，但是有超调和轻微振荡现象，橡胶管平均半径越大，得到的关节转角越大，但是转角响应的超调量也随之增大，FPA的初始角度越大，关节的转角越大，并且超调量减小，振荡减弱，但是上升时间增大，管接头出口面积的大小对关节FPA内腔压力的建立过程影响较大，但对关节转角的动态响应几乎没有影响，转动惯量和粘性阻尼系数对FPA内腔压力的动态过程几乎没有影响而对扭转关节转角有较大影响等结论。

Oneself design of the topic use number control tool machine to process center 藩 a town to process a box of body cover, impassability electricity and improvement which hope to find out a numerical words' application to process with traditional machine after the machine process realm in this design create the method that the painful machine processes, also hope passing this time designs better control and make use of a numerical words control to process center, for in the days to come of the work study much many backlog experience, pass a tutor to know industriously with oneself integrity of design process, to Chinese tradition handicraft of the machine process of the improvement have further of understanding with realize deeply;The machine of modern's processing realm is no longer a pure machine and process, it with calculator numerical turn and have inseparable contact, became 1 kind to influence place near situation mutually this a time's design to still apply a CAD etc.

本人设计的课题的用数控机床加工中心藩镇加工箱体盖，希望能在本次设计中找到数字话应用在机加工领域后与传统机械加工的不通电以及改良创痛机械加工的方法，也希望通过本次设计更好的掌握和运用数字话控制加工中心，为日后的工作学习多多积累经验，通过导师的辛勤知道和本人完整的设计过程，对中国传统手工的机械加工的改进有了进一步的了解和深刻的体会；现代的机械加工领域已不是单纯的机械加工，它与计算机数字化有着密不可分的联系，形成一种相互影响相互处近的局势本次设计还应用了CAD等等，希望为数控机械加工提供点心得谢谢

The information integrated pattern based on PDM/PLM in the course ofmanufacture is put forward. Under the constraints of building CAPP platform, thearchitecture of CAPP platform is established. The models of decision making andfunction for process planning are given. Then the development means of CAPP basedSmarTeam are extracted.3. The structure of modular product life cycle is established. Toward the divisionand planning of the General Modules oriented product family, theCAD/CAPP integrated model of flexible module based on feature and CAD/CAPPmapping model based on process planning match board are set up. The keytechnologies of Solidworks/SmarTeam/CAPP integration are studies.4. From the point of view of process match board and step match board, theprocess of creating to process planning match board is studied. As an example, themachining process planning of up beam of hydraulic press machines is used tointroduce the establishment of process planning match board by means of inferencebased on expert knowledge. The organize model about the process planning matchboard oriented product family is brought forward.5. The multi-decision methods of CAPP system based on analytic hierarchy aregiven.. On the basis of uniform data model, the sub-machining process planning ofpart is auto-created by means of analytic hierarchy, The step decision methods basedon AHP is put forward.6. For the design/manufacture information in the course of product life cycle, thetree structure based on Object-Oriented and static model based UML are founded. Themethod of establishing design/manufacture information management system isbrought forward. The commercial PLM software—SmarTeam is regarded asdevelopment platform, on basis of which, the design/manufacture informationmanagement system is built, and the multi-view mapping technique ofdesign/manufacture information model is studies.7. A computer-aided CAPP platform based on PDM/PLM is founded, and itsstructure, function, work flow is illustrated. Some example of the system areintroduced.

阐述课题提出的目的和意义，明确了本文研究的主要内容。2、提出基于PDM/PLM的制造过程信息化集成模式；在平台式CAPP系统的设计约束模型基础上，构建了平台式CAPP系统的体系结构；并给出工艺决策模型和功能模型；最后提出基于SmarTeam的CAPP开发模式和实现策略。3、建立模块化产品生命周期模型的组织结构；针对面向产品族的广义模块的划分和规划方法，建立基于特征的柔性模块CAD/CAPP集成模型及基于工艺模板的CAD/CAPP映射模型；研究Solidworks/SmarTeam/CAPP集成的关键技术。4、从工序模板和工步模板的角度研究了工艺模板的创建过程；以液压机上梁模块机加工为例，采用基于专家知识的推理技术实现了工艺模板的创成；提出了面向产品族的工艺模板分层结构树的组织模式。5、提出基于分层规划的多模式工艺决策流程；在统一数据模型的基础上，从特征层和零件层分层规划，实现了零件加工子工艺的自动创成；提出基于AHP的工步排序决策方法。6、针对产品生命周期中的设计/制造信息，建立了面向对象的类树结构和基于UML的静态结构模型；提出基于PDM/PLM软件的设计/制造信息管理系统的构建方法；以商品化PLM软件SmarTeam作为开发平台，开发了基于SmarTeam的设计/制造信息管理原型系统；研究设计/制造信息模型多视图映射机制。7、开发了基于PDM/PLM的平台式CAPP原型系统，构建了系统的功能模型，并对系统的主要功能进行说明，给出系统的运行实例。

Multitasking operating systems come in two flavors: cooperative multitasking and preemptive multitasking. Linux, like all Unix variants and most modern operating systems, provides preemptive multitasking. In preemptive multitasking, the scheduler decides when a process is to cease running and a new process is to resume running. The act of involuntarily suspending a running process is called preemption. The time a process runs before it is preempted is predetermined, and it is called the timeslice of the process. The timeslice, in effect, gives each runnable process a slice of the processor''s time. Managing the timeslice enables the scheduler to make global scheduling decisions for the system. It also prevents any one process from monopolizing the processor. Bs we shall see, this timeslice is dynamically calculated in the Linux process scheduler to provide some interesting benefits.

多使命操作体系可化分为两类：非抢占式多使命以及抢占式多使命所有像Unix的变种体系以及很多现代操作系同同样，Linux提供抢占式的多使命模式在抢占式多使命模式中，调度步伐决议啥子时候进程中止，新的进程能够开始得到运行这个被强制挂起的动作就叫做抢占进程在被抢占前，运行的时间是预知的，这个时间叫做时间片究竟上，时间片是为每一个运行态的进程分配处置惩罚器的时间的一片管理时间片，使能调度步伐为体系做好整个的局面：胸怀～调度决议时间片也能阻止任何一个进程垄断处置惩罚器正如我们看到的，在Linux进程调度步伐中时间片是蜂蜜面膜动态计算出来的，这样带来很多利益

In addition, we represent the variance of the process as a function of investment, as proposed by Hong and Hayya (1993), to decrease the number of defective items. Our models determine the optimal production lot-size, the optimal levels of investments, and the optimal levels of backorders that minimize the sum of inventory and quality-related costs.

另外，本研究并考虑藉由投资来降低制程的变异，其中利用Hong 等人(1993)所提出制程变异之投资函数，纳入总生产成本模式中考量，即投资后的制程变异为制程改善后所能降低的制程变异水准加上目前生产系统之最大变异水准与最低变异水准之差的指数分配关系，如此不仅能降低变异并提升制程能力指标，亦能让管理者利用本模式来比较不同制程改善的成本差异，推导出最佳生产批量、缺货量和投资成本，以提供存货管理者对生产决策之参考依据。

It's rather showy.I'd like something plainer.

赶花了，我想要素净些的。

The Kremlins Spassky Tower and passers-by are reflected in the wet cobblestones of Moscows Red Square on Feb.

克里姆林宫的斯巴斯克塔和旅客的身影倒映在潮湿的鹅卵石墙上。