查询词典 melt into

By adopting a special mixer, auxiliary equipment and a special manner of particle addition, the air bubbles and oxidic film produced in agitating process could be reduced effectively, so that the reinforcements could be distributed uniformly in the composite melt and almost 100% reinforcement particles can be absorbed by the composite melt.

因此可制得颗粒分布比较均匀、收得率可达100%的复合材料。

Recent studies of abyssal peridotites show that they are not melt residues of batching or fractional melting of pyrolite directly after melt extraction of MORB. Petrological studies of peridotites from Luobusa ophiolite massif also indicate that the mantle peridotites are not simple residues of primary pyrolite either.

罗布落蛇绿岩橄的镜下观察和岩石化学资料也证明，它不是原始地幔岩经局部熔化后的残余物，而且由来自更深层的地幔过渡带的硅酸盐超高压矿物底辟上升经熔取出玄武质熔体后，再次局部熔化后的残余物。

It indicated that the PES could be uniformly dispersed in melt ε-caprolactam with small domains depending on the strong interaction between the components, The hydrogen bonding was formed between the hydrogen atom on acid amide groups and the sulphone on PES resulting in the process of the dissolution of PES in melt ε-caprolactam being greatly accelerated.

结果表明，依靠其组分之间强烈的作用力，使PES能以较小的相畴均匀的分散在尼龙6基体中；酰胺基团上的氢原子能与聚醚砜中的砜基之间产生氢键作用，从而促进了聚醚砜在己内酰胺熔体中的溶解。

Tube, pipe fitting choice of hot-melt or bend, pipe fittings and hot-melt die.

管子、管件选用直管热熔或弯头，管件热熔机和模具。

NET and technology with data handling, designed and developed sublevel caving ore drawing computer simulation system with altitude may regard melt, intelligence melt and simulate precision, this system may solve any boundary conditions used in analysis research take off and ore drawing loss poor relevant various problems, have offered means and the method of science.

NET 和数据处理等技术，设计开发了高度可视化、智能化和仿真精度的崩落法放矿计算机仿真系统，该系统可用于分析研究解决任何边界条件下与放矿损失贫化有关的各种问题，为采矿工作者研究放矿问题提供了科学的方法和手段。

Based on the formation mechanism of amorphous particle in atomized Al-Ni-Y alloy powders, combining with the analysis of breakup modes of melt, a new approach to evaluate cooling rates of melt droplets in close-coupled gas atomization was presented.

摘 要：通过分析熔体破碎模式和非晶态颗粒的形成机制，提出一种表征紧耦合气雾化过程中熔滴冷却速率的新方法。

The results indicate that the cooling rate of melt droplet that can not break further depends not only on its diameter, but also on its position in atomizing chamber. As a result, the same sized particles in different positions show different cooling rates and two different kinds of microstructures. The cooling rates of melt droplets range from 104 to 108 K/s, and the critical cooling rate for glass formation of Al-Ni-Y is about 105 K/s. Moreover, the corresponding maximum diameter of amorphous particles is 25 μm, which accords well to the theoretical analysis results. The new approach, reflecting the complexity of close-coupled gas atomization objectively, is available and effective to evaluate the cooling behaviors of close-coupled gas atomization.

结果表明：在一定的工艺条件下，紧耦合气雾化存在多种破碎模式，熔滴的冷却速率因直径、雾化位置的差异，相同直径熔滴经历结晶和非晶化2种不同冷却行为；依据Al基合金粉末的粒度分布和微观结构，结合熔体的雾化过程及冷却模式，确定熔滴冷却速率的上、下限；实验得出熔滴的冷却速率为104~108 K/s，Al-Ni-Y合金的非晶化临界冷却速率为105 K/s，能形成非晶态的熔滴最大直径为25 μm左右，实验结果与理论分析结果较吻合，比较客观地反映紧耦合气雾化的复杂过程。

With the extruder moved away from the threaded substrate coating line, the extrusion condition are lined out and the die lip adjustments made to give a uniform melt at the desired output rate, die lip opening and melt temperature.

随着挤压机移离螺纹基片涂装生产线，就能达到挤压条件，模具口的调整能在理想产出率的上提供一个统一的熔体，即模具口开放和熔体温度。

When injected in the screw head melt pressure built up by the said injection pressure; Screw that promote the speed of the melt injection velocity, flow rate that injection rate; The trip itinerary said injection, in numerical plastic with pre-trip itinerary and said measures consistent.

注射时，在螺杆头部熔体所建立起来的压强称注射压力；螺杆推进熔体的速度称注射速度，其流率称注射速率；其行程称注射行程，在数值上与预塑行程与称计量行程相一致。

A redundant control circuit comprises a pair of heater circuits for heating a hot melt adhesive hose assembly to a predetermined temperature level, and a pair of temperature sensors which are used to sense the temperature of the hot melt adhesive hose assembly and to control energization of the heater circuits in order to maintain the desired temperature level.

一种冗余控制电路，包括用于将热熔胶软管组件加热到预定温度水平的一对加热器电路，和用于感应热熔胶软管组件的温度并控制加热器电路的电压以便维持期望的温度水平的一对温度传感器。

Therefore, it is imperative that you need to be prepared for the great change that is about to occur.

所以，你需要为快要出现的伟大改变准备好，这是必要的。

If u agree with our suggestion of dicker trade,we will exchange paper with u wood.

如果你方同意我们进行易货贸易的建议，我们将用纸与你们交换木材。