查询词典 maximum element

Carleman不等式及其在最优控制问题中的应用.Optimal control theory of distributed parameter systems mainly includes: Pontryagin's maximum principle; controllability; Hamilton-Jacobi equation (i.e., dynamic programming equation); time optimal control, etc.In this dissertation, we establish Pontryagin's maximum principle of optimal control problems governed by some nonlinear differential equations (parabolic differential equations, elliptic differential equations and 3-dimensional Navier-Stokes equations), which in particular could have local solut...

在这篇博士论文中，我们建立了非线性微分方程(包括抛物型微分方程，椭圆型微分方程以及3维Navier-Stokes方程)最优控制问题的庞特里雅金最大值原理，特别地，这些方程可能只有局部解或存在多解(我们称这样的系统为非适定系统，相应的最优控制问题为非适定最优控制问题)，以及适定的非线性发展方程最优控制问题的庞特里雅金最大值原理；我们研究了phase-field系统的时间最优控制问题以及Boussinesq系统的局部内可控性。

May preheat at 150°C maximum for 5 minutes maximum, then punch.

可以预热温度150℃，最高为5分钟为限，然后冲。

The primary pressure maximum and minimum occur during the daytime at 0900L and 1500L, respectively, while the secondary maximum and minimum during the nighttime at 2200L and 0400L, respectively. Additionally, the amplitude extremes of the primary pressure oscillations are larger than the secondary extremes.

每日最高气压和最低气压皆在日间（0900L和1500L）发生，因台北盆地日间受太阳辐射增温之影响，其气压振幅较大，且两者的相位也比一般中纬度地区提早1小时。

If θ=0?＃, it means that whisker axis is perpendicular to crack face, the energy dissipation caused by whisker-bridge join in zone of crack end achieves its maximum and the reintoughening effect of material achieves the best of all; along with growth of angle θ, the maximum principal stress in the matrix of whisker roots increases, when it achieves its limit, the whisker will be broken and orientation effect will be weakened.

当添加晶须与裂纹面法向形成角度θ时，随角度θ的增加，裂纹尖端拉应力增加。当添加角度较大时，晶须根部基体承受了较大的应力，易遭到破坏性崩裂。同时，晶须内部主应力与晶须轴向之间的角度也随角度θ的增加而增加，造成晶须折断，致使造成晶须拨出的体积分数φap减小，降低了增韧效果。

Utilizing the expression of maximum deviatoric stress yield rule on π plance and the relationship betwen π plane and principal stress this paper deduces and examines the shape and position of maximum deviatoric stress yield rule on π plane and the relation to Mises circle and Tresca hexagon .

利用π平面与主应力空间的关系及最大偏应力屈服准则在π平面上的表达式，推导验证最大偏应力屈服准则在π平面上图形的形状、方位及其与Mises圆和纯拉伸Tresca六边形的关系。

Maximum freedom means maximum productiveness ; our "openness" is to be the measure of our stability.

最大自由意味最大的生产力；我们的"自由开放"是我们经济稳定的标竿。

Maximum freedom means maximum productiveness; our "openness" is to be the measure of our stability.

最大话的自由意味着最大化的生产力；我们的"开放程度"是我们经济稳定性的衡量。

By applying the optimal tool parameters, the maximum tooth contact pressure is reduced by 45% and the maximum angular position error of the driven gear by 60%, in regard to the spiral bevel gear pair with a pinion manufactured by a cutter of straight-sided prole and of diameter determined by the commonly used methods.

通过应用参数的最佳工具，最大齿接触压力减少了45％，而最高的从动齿轮角位置误差60％，在关于由一个螺旋直齿轮刀具制造了一对锥齿轮双面形象和所常用的方法确定的直径。

In relation to the maximum pseudo time the corresponding maximum load is also required.

关于伪时间最长的相应最大载荷也是必需的。

In the biochemical analysis aspect, it is first time to use the simple fluorescence spectrophotometer to determine the protein in human serum by red alizarin as the probe of the RLS. The experiment shows that the system HSA-red alizarin has the maximum intensity of the RLS in Britton-Robison buffer of pH4.10 at maximum wavelength of about 360nm. The method has better linear range within 0.040-10.0ug/mL, determination limit is 0.040ug/mL. Moreover, We have selected three other dyes of chromotrope 2R, acid chrome dark blue and pyrocatechin violet as the probes of the RLS in determining protein in human serum and achieving satisfactory results.

在生化分析方面，作者首次使用简易960型荧光分光光度计，利用茜素红作为共振光散射光谱探针对人血清中的蛋白质含量进行了测定，测定结果显示在pH4.10的Britton-Robinson缓冲溶液，波长360nm处出现最大的共振光散射强度，其线性范围为0.040～10.0μg／mL，检出限为0.040μg／mL；另外，作者还筛选了其他三种可用作蛋白质测定的共振光散射光谱探针的有机染料：变色酸2R、酸性铬深蓝、邻苯二酚紫，并深入研究了测定的适宜条件和干扰情况，将这三种有机染料用于人血清中蛋白质含量的测定，均取得了满意结果。

"Second Life is remarkably easy to work with, and is very popular,"

"第二次生命是显着容易的工作，并且很受欢迎，"

For example, we usually assume that materials are homogeneous and isotropic and free of internal defects or flaws.

为了得到适合有限元分析的模型，我们必须经过如图2所示的简化步骤。