查询词典 maximum element

But the sun's rays then reach us despite having passed, first, through an enormous thickness of the higIT strata of the air, the minute dust of which reflects maximum of the higIT strata of the air, the minute dust of which reflects maximum of the blue rays away from us, leaving the complementary yellow light to pass on, Then, the somewhat coarser dust reflects the green rays, leaving a abundance orange-coloured light to pass on; and finally some of the yellow is reflected, leaving almaximum pure red.

这就充分呈现了低空尘埃的数量之大。但是太阳的光线终于到达了地面。它们先是穿过厚度极大的高空大气层，其中的细微尘埃把大部份蓝色的光反射掉了，让补色的黄光继续通行。然后，粗粒尘埃又反射掉绿色的光，让偏橙色的光继续通行。最后，部份黄色的光也反射掉，剩下几乎是纯红色的了。

An analytic solution of kinematic model was obtained via Lie transformation group. It shows that the velocity of particles flow is maximum when x=0. Through locating the maximum particles velocity distributing line and taking the line as the origin line of x coordinates, the modified kinematic model could simulate the eccentric discharging well.

通过Lie变换群得到"运动模型"的解析解，发现x=0时颗粒的垂直速度达到最大值，由此在确定颗粒最大速度分布线的基础上移动坐标使该线上x值均为0，对"运动模型"进行了修正，可以反映壁面对颗粒运动的影响，所得计算结果与实验测定吻合得很好。

Outpatient treatment is covered to a maximum of $50 per day, with a $500 Lifetime Maximum.

门诊治疗所涵盖的是，以最高达百分之五十天，与500美元的寿命最高。

But recent survey reported that Panicum maximum, a perennial grass in the family of Poaceae and listed as one of the twenty most noxious invasive plants in Taiwan has replaced the role of M sinensis in those areas. As a result of recurrent burning, A. confuse forest has been gradually replaced by the grassland of P. maximum. In this study, I compared morphological, photosynthetic, growth and life history characters of field growing P.

早期的研究指出：在大肚山与铁砧山区的本地植物芒草为当地相思树林反覆火烧后的最优势种；但近年来同一地区的研究显示：大黍已取代芒草的角色，而且发现大黍在火烧后植群覆盖度显著的增加，但芒草却没有相同的现象；反覆火烧使得大肚山地区的相思树林逐渐转变成以大黍为主的草生地。

At present, the printer through the parallel port, USB interface to connect with the computer, which can support USB interface for maximum speed of around 12Mbps Print speed, parallel port can be the maximum print speed of around 1Mbps only, so if the network printer to support the USB interface connector, then , we should allow it to interface with the computer through the USB connection.

目前打印机可以通过并口、USB接口来与电脑连接，其中USB接口可以支持最大速度为12Mbps左右的打印速率，并口所能达到的最大打印速率只有1Mbps左右，因此如果网络打印机支持USB接口连接的话，我们就应该让它通过USB接口与计算机连接。

In this study, both the maximum-likelihood methods and the maximum parsimony based sliding window analysis were used to evaluate the molecular evolution of Vip proteins.

本文采用最大似然方法和基于最大简约的滑窗分析对Vip蛋白的分子进化机制进行了评价。

The maximum error of regional anomaly separation is 3.101×10^(-6)m/s^2 the mean square error is 0.989×10^(-6)m/s^2 and the maximum percentage error is 7.76% for several data on the boundary and is lower than 4.1% for the other points.

分离出的区域异常最大误差为3.101×10^(-6)m/s^2，均方差为0.989×10^(-6)m/s^2，最大百分比误差仅在边部的几个数据上，为7.76%，其余各点的误差均小于4.1%。

It is pointed out that the error of indication E0 for the calibrated test length which are measured when the offset length between the ram axis and the stylus tip is zero shall neither exceed the maximum permissible error MPEE0 nor exceed 1/3 of the probe error,that the repeatability of E0 shall neither exceed the maximum permissible error MPE Rnor exceed the repeatability error of the probe,and that if the measuring data is rejected in acceptance and reverification,measurement must be carried at least 5 times at the same position for reducing the possibility of misjudgement.

提出探测轴探针针头零偏置长度的校准测试长度的示值误差E0应不超过最大允许校准测试长度的示值误差MPEE0，且不应超过测头误差的1/3；E0的重复性误差R不应超过最大允许重复性误差MPER，且不应超过测头的重复性误差。建议验收校准测量数据超差剔除后，必须在相应位置重复测量5次以上，以减小误判的可能性。

The admitted O quantity, which brings the photoemission current reach maximum then decrease to 90% of the maximum, is assumed to be best in the activation system.

在激活过程中，只要有过多的氧导入或过多的交替次数，都将使阴极灵敏度下降。

A better plane is the so-called maximum area plane, i.e. the plane on which the convex hull of the projection forms a maximum area.

一种更好的曲面被称为最大面积曲面，就是曲面所在的投影凸起外壳构成最大面积。

"Second Life is remarkably easy to work with, and is very popular,"

"第二次生命是显着容易的工作，并且很受欢迎，"

For example, we usually assume that materials are homogeneous and isotropic and free of internal defects or flaws.

为了得到适合有限元分析的模型，我们必须经过如图2所示的简化步骤。