查询词典 interpretation process

The static model of torsion joint is based on that of bending joint. The effects of structure parameters inside air pressure, initial angle, rube average radius, rube shell thickness on the turning angle are analyzed and the following conclusions are drawn: the relationship between the angle of torsion joint and the inside air pressure is basically linear, the angle of torsion joint increases with the initial angle and rube average radius, the angle of torsion joint decreases while the rube shell thickness increases. The kinetic equation is built for torsion joint. Simulating experiment implies that the time of inflating and deflating process is extremely shorter than that of kinetic process. So the pneumatic process can be ignored in actual system design and control. The factors that affect the dynamic features of torsion joint, such as shell thickness of rubber tube, average radius, initial angle, connector's outlet area, moment of inertia and viscous damping coefficient, are analyzed and the following conclusions are drawn: the change of rube shell thickness has no effects on the dynamic process of FPA inside air pressure while greatly affects the turning angle of torsion joint; when the rube shell thickness is small, the torsion joint has a bigger turning angle, no overshoot and long risetime, when the shell thickness is big, the turning angle of torsion joint is small, but has high response speed, overshoot and low shock; when the rube average radius increases, the turning angle of torsion joint increases and the overshoot increases too; when the initial angle of torsion joint is big, the turning joint is big, the overshoot is small and shock is low, but the risetime is big; the connector's outlet area affects the dynamic process of FPA inside air pressure greatly, but has no effects on the dynamic process of turning angle; moment of inertia and viscous damping coefficient have no effects on the dynamic process of FPA inside air pressure, but affect the dynamic process of turning angle greatly.

在弯曲关节模型推导的基础上，建立扭转关节的静态模型，并分析了扭转关节内腔压力，初始转角，橡胶管平均半径，橡胶管壁厚等参数对关节转角的影响，得出扭转关节的转动角度与充入FPA内腔的压缩气体压力之间基本呈线性关系，扭转关节的转角随初始角度和橡胶管平均半径的增大而增大，扭转关节的转角随橡胶管壁厚的增大而减小的结论；建立了扭转关节的动力学方程，仿真实验表明FPA的充放气过程与扭转关节的动力学过程相比时间极短，在实际系统设计和控制过程中可以忽略不计；分析讨论橡胶管壁厚，平均半径，初始角度，气体节流口面积，转动惯量，粘性阻尼系数等因素对扭转关节动态特性的影响，得出橡胶管初始壁厚的变化对扭转关节FPA内腔压力的动态响应几乎没有影响而对关节转角的响应曲线影响比较明显，壁厚较小时，关节可以得到较大的转角，并且转角的响应曲线没有超调，但上升时间长，壁厚较大时，关节转角变小，响应加快，但是有超调和轻微振荡现象，橡胶管平均半径越大，得到的关节转角越大，但是转角响应的超调量也随之增大，FPA的初始角度越大，关节的转角越大，并且超调量减小，振荡减弱，但是上升时间增大，管接头出口面积的大小对关节FPA内腔压力的建立过程影响较大，但对关节转角的动态响应几乎没有影响，转动惯量和粘性阻尼系数对FPA内腔压力的动态过程几乎没有影响而对扭转关节转角有较大影响等结论。

Oneself design of the topic use number control tool machine to process center 藩 a town to process a box of body cover, impassability electricity and improvement which hope to find out a numerical words' application to process with traditional machine after the machine process realm in this design create the method that the painful machine processes, also hope passing this time designs better control and make use of a numerical words control to process center, for in the days to come of the work study much many backlog experience, pass a tutor to know industriously with oneself integrity of design process, to Chinese tradition handicraft of the machine process of the improvement have further of understanding with realize deeply;The machine of modern's processing realm is no longer a pure machine and process, it with calculator numerical turn and have inseparable contact, became 1 kind to influence place near situation mutually this a time's design to still apply a CAD etc.

本人设计的课题的用数控机床加工中心藩镇加工箱体盖，希望能在本次设计中找到数字话应用在机加工领域后与传统机械加工的不通电以及改良创痛机械加工的方法，也希望通过本次设计更好的掌握和运用数字话控制加工中心，为日后的工作学习多多积累经验，通过导师的辛勤知道和本人完整的设计过程，对中国传统手工的机械加工的改进有了进一步的了解和深刻的体会；现代的机械加工领域已不是单纯的机械加工，它与计算机数字化有着密不可分的联系，形成一种相互影响相互处近的局势本次设计还应用了CAD等等，希望为数控机械加工提供点心得谢谢

The information integrated pattern based on PDM/PLM in the course ofmanufacture is put forward. Under the constraints of building CAPP platform, thearchitecture of CAPP platform is established. The models of decision making andfunction for process planning are given. Then the development means of CAPP basedSmarTeam are extracted.3. The structure of modular product life cycle is established. Toward the divisionand planning of the General Modules oriented product family, theCAD/CAPP integrated model of flexible module based on feature and CAD/CAPPmapping model based on process planning match board are set up. The keytechnologies of Solidworks/SmarTeam/CAPP integration are studies.4. From the point of view of process match board and step match board, theprocess of creating to process planning match board is studied. As an example, themachining process planning of up beam of hydraulic press machines is used tointroduce the establishment of process planning match board by means of inferencebased on expert knowledge. The organize model about the process planning matchboard oriented product family is brought forward.5. The multi-decision methods of CAPP system based on analytic hierarchy aregiven.. On the basis of uniform data model, the sub-machining process planning ofpart is auto-created by means of analytic hierarchy, The step decision methods basedon AHP is put forward.6. For the design/manufacture information in the course of product life cycle, thetree structure based on Object-Oriented and static model based UML are founded. Themethod of establishing design/manufacture information management system isbrought forward. The commercial PLM software—SmarTeam is regarded asdevelopment platform, on basis of which, the design/manufacture informationmanagement system is built, and the multi-view mapping technique ofdesign/manufacture information model is studies.7. A computer-aided CAPP platform based on PDM/PLM is founded, and itsstructure, function, work flow is illustrated. Some example of the system areintroduced.

阐述课题提出的目的和意义，明确了本文研究的主要内容。2、提出基于PDM/PLM的制造过程信息化集成模式；在平台式CAPP系统的设计约束模型基础上，构建了平台式CAPP系统的体系结构；并给出工艺决策模型和功能模型；最后提出基于SmarTeam的CAPP开发模式和实现策略。3、建立模块化产品生命周期模型的组织结构；针对面向产品族的广义模块的划分和规划方法，建立基于特征的柔性模块CAD/CAPP集成模型及基于工艺模板的CAD/CAPP映射模型；研究Solidworks/SmarTeam/CAPP集成的关键技术。4、从工序模板和工步模板的角度研究了工艺模板的创建过程；以液压机上梁模块机加工为例，采用基于专家知识的推理技术实现了工艺模板的创成；提出了面向产品族的工艺模板分层结构树的组织模式。5、提出基于分层规划的多模式工艺决策流程；在统一数据模型的基础上，从特征层和零件层分层规划，实现了零件加工子工艺的自动创成；提出基于AHP的工步排序决策方法。6、针对产品生命周期中的设计/制造信息，建立了面向对象的类树结构和基于UML的静态结构模型；提出基于PDM/PLM软件的设计/制造信息管理系统的构建方法；以商品化PLM软件SmarTeam作为开发平台，开发了基于SmarTeam的设计/制造信息管理原型系统；研究设计/制造信息模型多视图映射机制。7、开发了基于PDM/PLM的平台式CAPP原型系统，构建了系统的功能模型，并对系统的主要功能进行说明，给出系统的运行实例。

Multitasking operating systems come in two flavors: cooperative multitasking and preemptive multitasking. Linux, like all Unix variants and most modern operating systems, provides preemptive multitasking. In preemptive multitasking, the scheduler decides when a process is to cease running and a new process is to resume running. The act of involuntarily suspending a running process is called preemption. The time a process runs before it is preempted is predetermined, and it is called the timeslice of the process. The timeslice, in effect, gives each runnable process a slice of the processor''s time. Managing the timeslice enables the scheduler to make global scheduling decisions for the system. It also prevents any one process from monopolizing the processor. Bs we shall see, this timeslice is dynamically calculated in the Linux process scheduler to provide some interesting benefits.

多使命操作体系可化分为两类：非抢占式多使命以及抢占式多使命所有像Unix的变种体系以及很多现代操作系同同样，Linux提供抢占式的多使命模式在抢占式多使命模式中，调度步伐决议啥子时候进程中止，新的进程能够开始得到运行这个被强制挂起的动作就叫做抢占进程在被抢占前，运行的时间是预知的，这个时间叫做时间片究竟上，时间片是为每一个运行态的进程分配处置惩罚器的时间的一片管理时间片，使能调度步伐为体系做好整个的局面：胸怀～调度决议时间片也能阻止任何一个进程垄断处置惩罚器正如我们看到的，在Linux进程调度步伐中时间片是蜂蜜面膜动态计算出来的，这样带来很多利益

The process reuse architechure raised in the paper both support abstract process model cycle and practical process instance cycle mechanism, which can realizes dymamic improvement for both organization standard software process and practical project software process. So, the process reuse architecture provides necessary support for application of process improvement technology.

本文提出的过程复用框架同时支持抽象过程模型层面以及具体过程实例层面双重循环机制，可以实现组织标准软件过程和具体项目实例的动态改进，为CMM过程改进提供了一种具体的实施技术和方法，对过程改进技术的应用提供了必要的完善和补充。

The contents of the course include: what operating system are, what they do, how they are designed, and where they came from; a general history and explanations of computer system, and some discussion on hardware and the relation between operating system and other software; concept of process, process states and process control block, process queue, management of processes; concepts of sequent programming and parallel programming, process synchronization and its application, process communication; scheduling level and job state transition, job scheduling, process scheduling, and methods for scheduling; deadlock and its necessary conditions, deadlock prevention, control and recovery of deadlock; fixed partition, multiple partition and replacement partition memory management, swapping and overlays; page, segmentation and segmentation with paging storage management, basic concept of virtual memory management, and page, segmentation and segmentation with paging memory management.

课程的内容包括：计算机系统概述、操作系统的形成、发展、功能、特性、类型和发展趋势；操作系统的硬件环境、操作系统与其它系统软件的关系；进程的概念、进程的状态和进程控制块、进程队列、进程的管理；顺序程序设计和并行程序设计概念、进程间的同步与互斥、同步机构应用、进程间通信；调度的层次和作业状态转换，作业的调度、进程调度、调度算法；死锁问题的提出、死锁的必要条件、死锁的预防、避免、控制和恢复；固定分区、可复分区、多重分区内存管理技术以及覆盖技术和交换技术；分页域、分段域、段页域存储管理技术、虚拟存储管理的基本概念、分页域、分段域、段页域虚拟存储管理。

D seismic data interpretation can be regarded as adynamic interpretation process of oil reservoir descrip-tion.

四维地震资料解释可以看成是一个动态油藏描述过程，其解释方法可分成直接分析法、地震属性分析方法和动态储集层描述方法。

Based on the characteristic of multi resolution of wavelets analysis, a effective method for displaying any cross section from coarse to fine resolution is presented; Based on OpenGL, the paper improved Ray-Casting arithmetic and footprint arithmetic considering the characteristic of seismic data; After introducing the characteristic of geology data and the process of seismic interpretation, the paper presents a theory frame of 3D geological interpretation software and partly realize the frame.

本文首次利用小波变换实现了三维地震数据体的快速多分辨率显示；针对地震数据体的特点，提出了基于OpenGL的改进光线投影法的快速算法及改进的脚印算法；实现了地震数据体的切割、面状地质体的构造及面状构造与地震数据体的联合显示，动画效果的形成等三维地震数据体显示效果；分析了三维地质体的特点及常规地质解释过程的特点，提出了三维地学可视化软件的体系结构，并实现了其中主要功能，取得了良好的效果。

In order to investigate and monitor spartina alterniflora resources in the Luoyuan Bay, this paper illustrates the image process and interpretation based on the Landsat TM/ETM+ remote-sensing data of 2000 and 2006. On the base of the spectral analysis of different ground objects, NDVI and tasseled cap transform adopted on multi-spectral images, the algorithms for extracting and rectifying the spartina alterniflora from other landscape types were determined by decision tress classify in combination with visual interpretation.

为了对福建罗源湾互花米草进行监测研究，以2000年和2006年的LandsatTM/ETM+影像为数据源，在对不同地物进行光谱分析的基础上，结合进行了影像归一化植被指数和缨帽变换处理，建立了利用决策树分类法提取罗源湾互花米草的遥感解译技术。

Carry on structure analysis to the spare parts first, understand its structure characteristics to choose suitable semi-finished product and the semi-finished product manufacturing of the reasonable a craft thus;Then the technique request of spare parts carries on analysis, understanding it each process superficial accuracy grade and the surface rough degree, make it process the fixed position in the process and clip a tight way in assurance inside the scope of economic accuracy, draw up the machine of spare parts to process craft process thus and further, choose each work preface to process equipments and craft material, the assurance slices to pare dosage and craft size, computing the man-hour of each work preface settle sum.

首先对零件进行结构分析，了解其结构特点从而选择合适的毛坯以及合理的毛坯制造工艺；再零件的技术要求进行分析，了解其各加工表面的精度等级以及表面粗糙度，使其在经济精度的范围内确定加工过程中的定位和夹紧方式，从而进一步拟订零件的机械加工工艺过程，选择各工序加工设备以及工艺装备，确定切削用量以及工艺尺寸，计算各工序的工时定额。

If this is not specified, then it is defaulted to 25

如果这是没有指定，则默认为25

Cott invited his mother over for dinner.

COTT邀请母亲来他的房子晚餐。