查询词典 gap filling

The application of the gap element method in gap joint mechanisms is proposed. The stiffness matrix of the rotate joint elements and sleeve joint elements with gap elements are formed and the dynamic equation of the structure is given in the paper.

文中还提出了旋转铰和滑移铰两种间隙单元，推导了间隙单元的刚度矩阵，最后给出了含间隙单元的结构动力学方程。

Must cause the damper plate and the floodgate frame tallies, inspects the top and bottom packing surface with the feeler gauge the gap, makes the gap to maintain in 0.1mm, when gap exceeding the allowed figure, may the pad enter the slanting iron at the back of this place floodgate frame, simultaneously

需使闸板与闸框吻合，用塞尺检查上、下密封面的间隙，使间隙保持在0.1mm以内，间隙超标时，可在该处的闸框背面垫入斜铁，同时将膨胀螺栓略为旋松，直至间隙合格为止。

For the leaf area index of the three forest types, there was a similar variation trend, i.e ., increased first and decreased then, with the maximum presented in mid-July or August for Q. mongolica and J.mandshurica forests while in mid-August or September for F. rhynchophulla forest. The canopy porosity of the three forest types also had a similar variation trend, but opposite to leaf area index, being decreased first and increased then, with the minimum presented in mid-June, July, August or September. The analysis of variation coefficients of leaf area index, transmitted direct gap light, and transmitted diffuse gap light indicated that the spatial pattern of leaf area index in July-September was the main factor affecting the spatial distribution of transmitted diffuse gap light.

结果表明，3种林型的叶面积指数变化总体趋势是一致的，均呈先上升再下降的单峰曲线，蒙古栎林和胡桃楸林都是在7月中旬或8月中旬达到最大峰值，花曲柳林是在8月中旬或9月中旬达到最大峰值；3种林型冠层孔隙度的变化总体趋势也是一致的，呈先下降再上升的单峰曲线，不同样地峰值出现的时间也不同，最低峰值在6、7、8、9月中旬均有出现；通过对不同月份的叶面积指数、林下散射光、林下直射光的变异系数分析表明，7—9月叶面积指数的空间格局是影响林下散射光空间分布的主要因素。

A gear H62 which made in yellow brass with the same mode number m=0.34, 2mm thick and had a center hole, when the gap get C=0.5%t , and punched with compound punching die, and the dimension accuracy reached IT7, the part have a flat surface ,the verticality of tangent plane reached 89.5°, its roughness Ra magnitude are 12.5μm, height of burr are 0.10mm; and the punching part are punched with progressive die, the gap C=7%t , initial accuracy are IT11, and have an more rough surface, even can see the gap with eyes.

例如料厚t=1.5mm的H62黄铜冲裁件，选用C≤40%t单边Ⅰ类小间隙冲裁比选用C≤8%tⅢ类大间隙冲裁，冲件固定误差将加大40%～60%，精度至少降一级。

On the basis of B-Rep of CAD data and ACIS library,a technology of surface filling based on loop feature handling and outlines smoothing is presented in the paper,filling for the surface with complex concave edges is also studied in the paper.

以CAD数据的边界表示法和ACIS几何开发库为基础，提出了基于环特征处理和外边界光顺的曲面填充技术，对含有复杂凹缘的汽车覆盖件曲面填充进行了研究。

This is a computer graphics to fill the graphics algorithms, including seeds filling simple filling algorithm and scanning fill algor...

这是一个计算机图形学中图形填充的算法，包括种子填充中简单填充算法和扫描线填充算法！

The filling process and temperature field of the die has been coupling simulated by using software of ProCAST, from which the filling states and temperature changes of the die was shown animatedly.

利用ProCAST软件对铝合金压铸模具进行温度场和流场的耦合模拟，动态展示了模具的充型过程和模具稳定工作时的温度场变化。

The mathematical model was verified in experiment with the method of indirect squeeze cast Archimedean spiral proof sample. And the experimental results show that the maximum deviation between the theoretical value and measured value is less than 8%. This model can be used for quantitative analysis and estimating effects of the craft factors on the filling ability, and can also predict the maximum filling length. It has the important reference value to design the semi-solid alloy rheoforming technology and mould.

采用间接挤压铸造阿基米德螺旋线试样的方法对该数学模型进行了实验验证，实验结果表明：理论计算值与实验测定值之间的最大偏差小于8%；该数学模型可以定量分析和估算工艺因素对充型能力的影响，并可预测充型极限长度，这对半固态合金流变成形工艺设计和模具设计都有参考价值。

Filling up according to IMD guide in SBO and BEAS, filling all fields related to production issues.

创建新项目，在SBO和BEAS里根据IMD指示填写相关项目。

The relaxation results showed that La filling had significant effects on the geometrical structure of CoSb3. In addition to that, La filling made the bond length, bond angle and charge density change.

CoSb_3为窄能隙半导体，在其能带结构的Γ点附近靠近费米面的能带呈直线的形状，且与k矢量成线性的关系。

That's what makes this mod unique.

这也正是这个MOD独特。

I now feel furious and want to do something.

现在我觉得非常气愤，想做点什么。