查询词典 diameter

Rational new method for checking ring gauge is put forward in this paper. For pitch less than 0.5 mm check plug is used to inspect size on virtual effective diameter and simple effective diameter, but for pitch over 0.5 mm, check plug is only used to inspect size on virtual effective diameter, simple effective diameter is measured by double ball.

提出了对于螺距不大于0.5 mm的螺纹环规，采用校对规检验作用中径及单一中径；而对于螺距大于0.5 mm的螺纹环规，则采用校对规检验作用中径，双球法测量单一中径。

Rational new method for checking ring gauge is put forward in this paper. For pitch less than 0.5 mm check plug is used to inspect size on virtual effective diameter and simple effective diameter, but for pitch over 0.5 mm, check plug is only used to inspect size on virtual effective diameter, simple effective diameter is measured by double ball.

提出了对于螺距不大于0.5 mm的螺纹环规，采用校对规检验效用中径及单一中径；而对于螺距大于0.5 mm的螺纹环规，则采用校对规检验效用中径，双球法测量单一中径。

Pitch circle diameter: d = mz = 3X12 = 36 Tooth crown heights: ha = m (f0 + x)= 3X (l +0.5)= 4.5 Tooth High: hf = m (f0 + cx)= 3X (l +0.25-0.5)= 2.25 Tooth full height: h = ha + hf = 4.5 +2.25 = 6.75 Addendum circle Chemical pumps diameter: Da = d +2 ha = 36 +2 X4.5 = 45 Fixed string tooth thickness: Sxn = m (π/ 2 * cos2a + xsin2a)= 3X (1.387 +0.6428 X0.5)= 5.125 Fixed string of high gear tooth thickness measurement: hxn = m (π/ 8 * sin2a + xsin2a)= 3X (0.7476X0.117X0.5)= 2.42 Modulus coefficient x0.5 m3 O20 ° pressure angle tooth thickness Sxn5.12 fixed string Addendum Coefficient string f1 fixed gear tooth thickness measurement most high hxn2.42 Teeth z12 2, shaft wear and tear maintenance: Axis gear pump wear is mainly because with the support roller shaft at both ends between the friction and wear, so that smaller shaft diameter.

分度圆直径：d=mz=3X12=36 齿顶高：ha=m（f0+x）=3X（l+0.5）=4.5 齿根高：hf=m（f0+c-x）=3X（l+0.25-0.5）=2.25 齿全高：h=ha+hf=4.5+2.25=6.75 齿顶圆直径：Da=d+2ha=36+2X4.5=45 固定弦齿厚：Sxn=m（π/2*cos2a+xsin2a）=3X（1.387+0.6428X0.5）=5.125 固定弦齿厚测量用齿高：hxn=m（π/8*sin2a+xsin2a）=3X（0.7476X0.117X0.5）=2.42 模数m3变位系数x0.5 齿形角o20°固定弦齿厚Sxn5.12 齿顶高系数f1固定弦齿厚测最齿高hxn2.42 齿数z12 2、轴的磨损维修：齿轮泵中轴的磨损主要是因为轴两端与支撑滚针间的摩擦磨损，使轴径变小。

The preoperation diameter of ascending aorta was taken as baseline. Patients were divided according to its baseline aortic diameter into diameter0 mm group and diameter≥40 mm group, furthermore, the patients were also divided according to echocardiographic findings into bicuspid aortic valve group and tricuspid aortic valve group.

以术前升主动脉直径为基础值，按基础值的大小分为直径﹤40mm组和直径≥40mm组，并按主动脉瓣形态分为二叶主动脉瓣组和三叶主动脉瓣组。

Both break through the rules which request that the bore diameter should be bigger than the steel bar diameter trebly or not smaller than the steel bar diameter adding 50mm.

4设计锚孔直径50，锚筋直径28，突破了规范关于锚孔直径需大于锚筋直径3倍或不小于锚筋直径加50mm的规定。

The bending radius during installation: For non-armored digital signal cable for railway with plastic sheath, composite sheath and Al sheath, the bending radius is not less than 10 times of outer diameter of cable; For armored cable, the bending radius is not less than 15 times of its outer diameter; For railway inner digital signal cable, the bending radius is not less than 20 times of its outer diameter.

2.4敷设时的弯曲半径：塑料护套、综合护套、铝护套铁路数字信号电缆非铠装电缆应不小于电缆外径的10倍；铠装电缆应不小于电缆外径的15倍；内屏蔽铁路数字信号电缆应不小于电缆外径的20倍

The main technical parameters of equipment The largest diameter rod into the Φ8mm Diameter round Φ1.20mm-Φ3.5mm The maximum speed cable 25m / s Cable drum diameter Φ450mm Road stretching up to 13 defective Chu-line maximum length of 9m Set-up specifications PND500, PND630 13 die final round adjustable model separate motor

设备主要技术参数最大进杆直径Φ8mm 出线直径Φ1.20mm-Φ3.5mm 最高拉线速度 25m/s 拉线鼓轮直径Φ450mm 最多拉伸道次品 13道储线器最大长度 9m 收线盘规格 PND500，PND630 最终出线模 13模可调。

First, the main technical parameters of equipment The largest diameter rod into the Φ8mm Diameter round Φ2.0mm-Φ3.5mm The maximum speed cable 25m / s Cable drum diameter Φ450mm Road stretching up to 9 defective Chu-line maximum length of 9m Set-up specifications PND500, PND630 Final round 9-mode adjustable model.

一、设备主要技术参数最大进杆直径Φ8mm出线直径Φ2.0mm-Φ3.5mm最高拉线速度 25m/s拉线鼓轮直径Φ450mm最多拉伸道次品 9道储线器最大长度 9m 收线盘规格 PND500，PND630最终出线模 9模可调。

But when the cholesterol was substituted by its oxide result, the membrane life time extended to nearly 60 hrs ;besides the diameter of the hole on which the membrane exists 、temperature、PH value cause great effects to the life time of the membrane, and the diameter was the most important element. When the diameter larger than 3mm it is almost no way to form a membrane on the hole under experiment condition. Between 1mm and 3mm it has a better result by change the prescription of the membrane. when it is 0.5mm all the membrane can last more than 40 hrs ,and the prescription like Och : phosphatidylcholine / cephalin＝4:1; 3:1; 2:1; 1:1; 2:3 need the request of the experiment basically, when cooperate with multi hole structure it is very to detect the concentration and found the model.

研究结果说明，成膜在普通胆固醇/磷脂配方下不能达到满意的结果，无论如何改变外界条件成膜始终超不过7小时，而将胆固醇换成氧化胆固醇再和磷脂按照一定配比的时候，成膜时间则大大延长，可达60h左右；另外除成膜配方，成膜孔径、温度、PH值等因素对成膜有着很重要的影响，成膜孔径对膜的影响最为关键，在3mm以上的孔径时成膜比较困难，在1－3mm适当提高成膜液浓度可以改善，孔径为0.5mm左右成膜比较稳定基本都能达到40h以上，合适的几个配方如卵/脑磷脂：氧化胆固醇＝4：1；3：1；2：1；1：1；2：3基本满足实验要求，配合一板多孔结构，可以保证单位时间的离子传输量的检测和计算。

The profile of the sleeve trim shall be that of a cone, reducing conically from a full pipe diameter at the inlet, to reduced diameter at the mid-point of the sleeve, and retaining the reduced diameter through to the outlet of the sleeve.

套管的外形应该是一个锥形，从进口端与管道直径完全一样的截面成圆锥形逐步缩小，缩小到套管的中点，然后保持相同的直径和截面直到套管的出口端。

What was it that made you want to change sider ?

是什么使你临阵倒戈？

I don't know what he wants, but let's play along with him.

我不知道他要干什么，可我