查询词典 commanding height

Due to difficulty of evaluation of micro grit protrusion topography after dressing of diamond grinding wheel, valid grit protrusion height, mean grit edge angle and grit protrusion homomorphy were proposed as characteristic parameters to evaluate iso-height behavior of grit protrusion, cutting behavior of grit edges and crystal integrity of diamond grit protrusion.

针对金刚石砂轮修锐后磨粒微观出刃形貌的很难评价的问题，建立有效磨粒出刃高度、平均磨粒出刃角和磨粒出刃同形度的特征参数模式，分别评价砂轮工作表面的磨粒出刃等高性、磨粒切削性能和磨粒出刃结晶完整性。

Big bitmaps will confine to the entire area of this control with a vertical scroll bar on Right side ( the scroll bar will be displayed if the height of the image is greater than the height of this control) and a horizontal scroll bar at the bottom of this control (the scrollbar will be displayed if the width of the image is greater than the width of this control).

大位图将只对本一份关于右侧垂直滚动条控制整个地区（滚动条将显示，如果图片的高度大于这个控件的高度）和水平滚动条的底部此控制（滚动条将显示，如果图像的宽度大于这个控件的宽度更大）。

Inadequateness leads to thin artificial barrier, which cannot form a low permeable or impermeable artificial barrier, which just cause lower differential pressure, this cannot control the extension on the height effectively.Moreover, because the artificial barrier cannot achieve the function of the height controlled, finally make the projection less efficiency, even could be defeated comes to an end.

过少则人工隔层过薄，不能形成一个低渗透或不渗透的人工遮挡层，只能在裂缝垂直方向上形成较小的压降，从而不能更有效的遏制裂缝在纵向上延伸；另外，由于遮挡层起不到控制缝高的作用，降低了压裂效率，最终施工效果不明显，甚至会以失败告终。

In this paper we consider the enumeration of subsets of the set, say D, of those Dyck paths of arbitrary length with maximum peak height equal to m and having a strictly increasing sequence of peak height.

本文考虑了由最高峰的高度为m，并且峰的高度沿着Dyck路严格递增的所有Dyck路组成的集合，即集D的子集的计数问题。

In this paper we consider the enumeration of subsets of the set, say Dm, of those Dyck paths of arbitrary length with maximum peak height equal to m and having a strictly increasing sequence of peak height.

孙怡东 ，贾藏芝本文考虑了由最高峰的高度为m，并且峰的高度沿着Dyck路严格递增的所有Dyck路组成的集合，即集合Dm的子集的计数问题。

In this paper,utilizing the technology of computer simulation,the change of aluminium electolysing cell incrustation was computed and studied under the condition of different aluminium liquid height ,and the optimal aluminium liquid height was determined.

本文利用计算机仿真技术，对我国某铝厂160kA 大型预焙阳极电解槽在不同铝液水平时槽帮结壳的变化进行了计算研究，并确定了铝电解槽正常生产时最佳的铝液高度。

Therefore, the authors suggested that a coefficient of correction for correcting height index measurement error should be established when the height is measured in the afternoon, so as to enhance measurement efficiency and measurement objectivity.

青少年身高在一日中发生变化，因此，在下午测量时，为了提高测试效率及测量的客观性，建议制定修正身高指标测量误差的系数。

And 17. 6% respectively when increasing furnace arch height 10 times original height and adopting furnace arch stmcture of inequilateral depth and double fumace arch structure.

研究表明，当折焰角高度增加为原高度的10倍、采用左右不等深度折焰角和双折焰角三种结构时，炉膛出口残余旋转明显减小，末级再热器入口截面最大速度不均匀性系数M〓可分别减小30.7％、19.3％和17.6％。

Results indicate the local high point height and additional tension stress of rolled strip are proportional to local high point initial height of strip, decrease as roll.

研究结果表明：轧后带钢局部高点高度及附加张应力的大小与来料高点高度成正比，随总轧制压下率的增大而减小。

The results showed that there were intraspecific differences in plant height and stem diameter of tolerant clones, and plant height and stem diameter of sensitive clones decreased significantly.

结果表明：(1)割手密耐性无性系株高和茎径对UV-B辐射响应具有明显的差异；敏感无性系的株高和茎径显著或极显著的下降。

Pachomius manual labour was organized as an essential part of the monastic life; and since it is a principle of the monks as distinguished from the mendicants, that the body shall be self-supporting, external work of one sort or another has been an inevitable part of the life ever since.

根据圣pachomius体力劳动组织作为一个重要组成部分寺院生活；以来，这是一个原则的和尚，作为有别于乞丐，该机构应自支撑，对外工作的这种或那种已一个必然的一部分，生活至今。

In order to study the effects of parametrical rolling on the ship movement and tilts, in allusion to ship's navigating in regular following waves, the equation of ship rolling motion is transformed into normal Mathieu equation by proper variable replacement when strong parametrical excitation in restoring moment varied according to sine or cosine wave.

为研究参数横摇对船舶运动和倾覆的影响，通过对船在规则波上随浪航行时，恢复力矩中出现的1个以正余弦规律变化的强参数激励项进行适当的变量置换，将船舶的横摇运动方程转换成标准形式的Mathieu方程。