查询词典 combustion engine

These results clearly justifies that in combustor, the injector location and its conditions have no effect on the flowfield structure but have strong effect on the combustion efficiency, and that inside the engine, undesirable injector conditions can result in the engine thermal choked and unstart.

第五章计算了含横向喷流的二维燃烧室和一种简化一体化超燃冲压发动机流场，发现在燃烧室中喷口位置及喷射条件对流场的结构影响不大，但对燃烧效率却有较大的影响；而在发动机内部，不适当的喷射条件，有可能引起发动机的&热壅塞&，使发动机无法启动。

An experiment is performed on a single-cylinder carbureted gasoline engine Honda G200, to study the dynamical performance,combustion performance and emission perfonmance of engine.

6在Honda G200型单缸化油器式发动机上进行富氧燃烧试验，研究富氧助燃下发动机的动力性能、燃烧性能及排放性能。

The assembly of journal and plain bearing liner space is too little, force of organic still oil pressure is small it is the crucial index that affects lubricant result, make lubricate because of lacking engine oil between crankshaft and plain bearing liner and bite dead invalidation, include to be pulled badly, lack lube, layer of alloy of dry attrition generation is fused, grind sliding surface to did not maintain the oily film of certain ply, and all sorts of local overload exhaustion are destroyed, cavitation erosion and V form are destroyed etc, through technology of him director diesel locomotive old experience reachs the analysis of pair of its breakdown reasons, put forward precautionary measures especially. As a result of,the burns caustic mechanism plain bearing liner to burn caustic mechanism of 1 plain bearing liner is the lube film burst between journal and plain bearing liner, cause plain bearing liner and crankshaft generation clash, below high temperature, high pressure and high rotate speed, the wear-resisting alloy layer of plain bearing liner wears away prematurely or fuse, cause plain bearing liner and crankshaft to stick thereby bite, can make the steel back of plain bearing liner and Kong Zhong produces whirligig, inlet port is jammed, carry on the back by steel again with the friction of aperture causes high temperature to make plain bearing liner burned-out further, can cause bolt to break off, happen swing a malign accident that pounds cylinder body of bad internal-combustion engine.

轴颈和轴瓦的装配间隙太小，还有机油压力低是影响润滑效果的关键指标，使得曲轴和轴瓦之间因缺少机油润滑而咬死失效，包括严重拉伤，缺少润滑油，干摩擦产生合金层熔化，磨滑面没有保持一定厚度的油膜，以及各种局部过载疲惫破坏，气蚀和V形破坏等，通过本人主管内燃机车技术多年经验及对其故障原因的分析，特提出预防办法。1轴瓦的烧损机理轴瓦烧损的机理是由于轴颈和轴瓦之间的润滑油膜破裂，导致轴瓦和曲轴产生摩擦，在高温、高压和高转速下，轴瓦的耐磨合金层过早地磨损或熔化，从而引起轴瓦和曲轴粘咬，会使轴瓦的钢背和座孔中产生旋转运动，进油孔被堵塞，再由钢背和座孔的磨擦进一步引起高温使轴瓦烧坏，并会造成螺栓折断，发生甩出捣坏内燃机缸体的恶性事故。

The cooling pump is belt-driven by the combustion engine crankshaft, resulting in a direct coupling of engine and cooling pump speeds.

受驱动方式的限制，风扇和水泵转速依赖于发动机的曲轴转速，不能根据发动机的不同工况自动调节。

With CAD/CAM integrated modeling technology and NC programming manufacturing to develop cold box process casting technology of engine cylinder block and cylinder head of linear four-cylinder,two-air valve mid-position cam,four-stroke direct-jet combustion chamber,drying cylinder sleeve turbocharged and oil intercooled diesel engine in accordance with EUROⅢ standard of automobile tail gas exhaust.

运用 CAD /CAM一体化复合建模与数控编程加工技术，研究开发了符合欧Ⅲ汽车排放标准的直列四缸、二气门中置凸轮、四冲程直喷燃烧室、干式缸套涡轮增压和机油中冷式柴油发动机缸体缸盖冷芯盒铸造成形工艺。

Engine main bearing is one of the most important tribological elements in internal combustion engine.

内燃机主轴承是内燃机最重要的摩擦副之一。

Combination of engine and other devices, such as with the non-driven equipment and for mutual or common traction motor and internal combustion engine that contains the original motivation ...

发动机与其他装置的组合，如与非从动设备与用于相互或共同牵引的包含电动机和内燃机的原动机。。。

The highly efficient Atkinson-cycle engine, made possible by the Variable Valve Timing with intelligence system, allows the expansion/power stroke to be longer than the compression stroke so that combustion energy can be more effectively used for production of engine power.

高效的阿特金森循环发动机，作出与智能可变气门正时系统，可以使扩充/动力冲程要长于压缩冲程，使燃烧的能源可以更有效地用于生产发动机力量。

Acknowledge that the following practical cycles can be heat engine cycle of ideal gas, such as the internal combustion engine , Diesel cycle , Brayton cycle.

了解并掌握内燃机和燃气轮机装置的实际工作循环可抽象为理想气体的热机循环。

The steam engine is an external-combustion engine.

蒸汽机就是一种外部燃烧发动机。

Must have Coordination and negotiation skill, flexible ideas, and be punctilious person.

必须具备较好的协调与谈判能力，头脑灵活，工作认真仔细

Result: 18 patients are all with simple eye.The pigment mole lies in nasal and temple sides of the ball conjunctiva,in which 2 lie in lacrimal caruncle and semilunar plica.

结果：18例患者均为单眼，色素痣大多数位于内外侧睑裂部球结膜面，2例位于泪阜及半月皱襞，经激光治疗后，10例色素痣消失，有5例行再次激光后消失，2例行第三次激光后消失，1例第四次激光后消失。