查询词典 bulk density

Result After addition of wood vinegar, the fermentation temperature of sawdust was obviously increased, and the highest temperature reached 67.0℃,being 3.5℃ higher than that of CK, and the days when fermentation temperature was above 55℃ reached 57 d, being 40 d more than that of CK. After addition of wood vinegars, the bulk density, water-holding voidage and total voidage of sawdust before and after maturity were all higher than that of CK, pH value and EC value were all lower than that of CK, and the proportion of sawdust whose particle size was smaller than 0.5 mm was higher than that of CK, and that of sawdust whose particle size was 0.5-1.0 mm and bigger than 1.0 mm were lower than that of CK.

结果］添加木醋后，木屑的发酵温度明显提高，最高温度为67.0℃，比对照高3.5℃，发酵温度大于55℃的天数达到57 d，比对照多40 d；添加木醋后，木屑的容重、持水空隙度和总空隙度腐熟前后均高于对照，pH值和EC值均低于对照，粒径＜0.5 mm的木屑所占比重高于对照，粒径为0.5~1.0 mm和＞1.0 mm的木屑所占比重均低于对照。

Using the one-atom theory, the electronic structures of Pt-electrocatalyst with fcc structure was determined as follows:(5dn)6.48 (5dc)2.02 (6sc)1.48(6sf)0.02. Compared to the result obtained by the first-principle method such as FP-LMTO, CASTEP, their results are in good agreement with each other. Comparing the calculations of physical properties such as lattice constants, cohesive energy and bulk modulus by OA method and first-principle method, the result obtained by OA method is in excellent agreement with experimental value, but the result obtained by first-principle method is not accordable. The relationship between the electronic structures and catalytic performance was explained qualitatively by OA method and first principle method according to its electronic structures. Because the d-orbital vacancies increases and static density is high around Fermi energy band, Pt has good catalytic performance.

摘 要：依据纯金属单原子理论确定面心立方结构电催化剂Pt的电子结构为(5dn)6.48(5dc)2.02-(6sc)1.48(6sf)0.02，与采用第一原理的FP-LMTO和CASTEP等方法所计算的电子结构相比较，其结果非常相近；由OA理论和第一原理方法计算的晶格常数、结合能、体弹性模量等物理参数进行比较，OA理论计算的结果与实验值较符合，而第一原理方法计算的结果与实验值相差较大；在此基础上用OA理论和第一原理方法研究了Pt的电子结构与催化性能的关系，由于d带空穴增多和费米能级附近态密度较高，导致金属Pt的催化性能很好。

RESULTS:Automatic bed coating granulator preparation of pellets has biggest bulk density, smallist caesural corner and filling quantitative difference.

结果 ：全自动包衣造粒机制备的微丸堆密度大、休止角小、填充装量差异小，全自动包衣造粒机制备微丸既能保证微丸质量，又能提高效益。

It is directly perceived through the test resultsthat a difference exists between castable amount per unit volume and bulk density.

指出了耐火浇注料单位体积用量与体积密度定义上的区别，并且介绍了一种测试耐火浇注料单位体积用量的试验方法。

The results showed that the structure characteristics of block cloddy was with tight surface but loose inner, the bulk density of the crust can be high as 1.39~2.0g/cm^3, which was mainly affect by unreasonable tillage process. The tight surface can not be crushed by nature alternation of drying and wetting. Farming machinery to impact and rotary tillage were necessary when reduce them.

结果表明不合理耕作所产生的块状结构体具有外部极为密实而内部相对疏松的构造特征，外壳的容重高达1.39~2.0g/立方公分以上，仅依赖于自然干湿交替作用使其碎散成小的土团成为不可能，必须运用机械击打、旋耕切割等方法进行破碎。

The granularity and broken cellular wall of ultra-fine powder were studied by JL9200 laser analytical instrument of granularity and scanning electron microscopy, as well as the bulk density and liquidity of "Cumiansan" ultra-fine powder were measured, and compared to the commonly cribble.

应用激光粒度仪和扫描电镜对微粉的粒度和破壁情况进行了观测，测定了&促免散&微粉的堆密度及流动性，并与普通粗粉进行了比较。

The results showed that the D50 of Astragalus membranaceus and Epimedium brevicornum ultra-fine powder were 6.82μm and 8.40μm separately. The broken cellular walls of two ultra-fine herbal powder were bigger than those of the commonly cribble, and intact cells were not visible under SEM, and it improved the mixed uniformity. On the contrary, organization blocks of the commonly cribble were clearly discernible, also the shape and granularity were irregular, and the organization cells were still complete. The bulk density and liquidity of Astragalus membranaceus and Epimedium brevicornum increased significantly after ultra-fine Smashing. The component icariin extraction content of the ultra-fine powder was enhanced by 18.31% compared with the cribble by the chromatograph analysis of icariin. At the same time, Astragalus membranaceus polysaccharide and Epimedium brevicornum polysaccharide content of the ultra-fine powder were enhanced by 117.13% and 315.15% compared with the cribble.

结果发现黄芪和淫羊藿经超微粉碎后，粉体的粒度分布中心D_(50)分别为6.82μm和8.40μm，经电镜观察均难以看到完整的细胞形态，只能看到细胞碎片，破壁率远远大于普通粗粉，其混合的均匀度显著提高，而普通粗粉在显微镜下，组织块清晰可见，且形状不规则，粒径分布不均匀，组织细胞仍然完整；超微粉碎后，黄芪和淫羊藿的堆密度和流动性显著增强；通过对淫羊藿有效成分淫羊藿苷的色谱分析，其中淫羊藿超微粉的淫羊藿苷体外溶出量较淫羊藿粗粉中提高了18.31%；同时黄芪、淫羊藿超微粉多糖的提取率分别较黄芪、淫羊藿粗粉提高了117.13%，315.15%。

The carbon foam were prepared by self-bubbling at high pressure from AR pitch added sodium dodecyl benzene sulfonate and Span-40, respectively. The bulk density, pore rate, compressive strength, thermal conductivity at room temperature and crystallitic parameters of carbon foam were measured. The rheological properties of AR pitch and pore structure of carbon foam were investigated.

以十二烷基苯磺酸钠和Span-40表面活性剂为添加剂，AR沥青为原料，制备炭素泡沫材料，测定了材料的体积密度、显气孔率、压缩强度、常温热导率以及微晶结构参数，研究了添加表面活性剂后AR沥青的流变性能和炭素泡沫材料孔胞结构的变化。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

We have limited budget let me know if you can do this competitively.

我们有限的预算让我知道如果你能做到这一点竞争力。

We don't know how other critters breathe--lizards, for example.

我们还不知道诸如蜥蜴之类的动物如何呼吸。