英语人>网络例句>allowable deviation 相关的网络例句
allowable deviation相关的网络例句

查询词典 allowable deviation

与 allowable deviation 相关的网络例句 [注:此内容来源于网络,仅供参考]

Four logical deviation are elaborated including the deviation identity, the deviation law of contradiction, the deviation law of excluded middle, the deviation law of sufficient reason. The humorous effect of applying these logic deviation makes one laugh and is thought- provoking.

阐述了偏离四大逻辑规律,即偏离同一律、偏离矛盾律、偏离排中律、偏离充足理由律所取得的幽默效果,既令人发笑,又耐人寻味。

The permissible deviation: verticality: it allows a standard deviation of no more than 1.5mm: two of the adjacent disk at the top permits a deviation no more than 2mm, the straddle disks at the top allows a deviation of no more than 5mm; disk face error: the adjacent disk permits a deviation no more than 1mm between the two edges, the straddle stets more than 5mm; indirect slit of the disks is no more than 2mm

允许偏差:垂直度:允许偏差不大于1.5mm 水平偏差:相邻两盘顶部允许偏差不大于2mm,成列盘顶部允许偏差不大于5mm ;盘面偏差:相邻两盘边不大于1mm ,成列盘面不大于5mm ;盘间接缝不大于2mm 。

Both deviation analysis method based on correction coefficient and deviation analysis method based on deviation factor are presented by introducing the principle of deviation analysis. With an instance, the influence on heat consumption or coal consumption rate by the deviation of main operational parameters and technical economy indexes are quantificationally calculated.

在阐述偏差分析机理的基础上,提出基于校正系数的偏差分析方法和基于偏差因子的偏差分析方法,结合实例,定量地反映出主要运行参数和经济技术指标的偏差对机组热耗或煤耗的影响。

As for the factitiously specified allowable values,such as allowable deflection,allowable amount of wear,and so on,their magnitudes,which are confirmed on the basis of empirical formula,often have an interval value or a limit value,therefore they can be described suitably by minor type membership function, As for various strength values of parts,such as tensile strength,compression strength,contact strength and so on,their magnitudes,which are often confirmed only by approximate mean,can be described suitably with middle type membership function.

对于人为规定的各种许用值,如许用挠度值、许用磨损量等,根据经验公式确定它们的大小时往往有一个区间或一个极限值,宜用偏小型隶属函数描述,对于零件的各种强度值,如抗拉强度、抗压强度、接触强度等,实际中往往只能确定其近似的均值,宜用中间型隶属函数描述。

Extract information based on the instantaneous features : In the center is one of the instantaneous rate of the power spectral density of the maximum, is a center to the absolute value of the instantaneous rate of the standard deviation, Non-zero weak signal instantaneous phase of the nonlinear component absolute standard deviation, Non-zero weak signal instantaneous phase of the nonlinear component standard deviation, In the center is one of the non-weak signal of the absolute value of the instantaneous frequency standard deviation, a signal to one of the instantaneous frequency of the power spectral density of the maximum, According to 16QAM and QPSK signals XI axis projection in the different performance parameters raised.

提取信号七个基于瞬时信息的特征:零中心归一化瞬时幅度功率谱密度的最大值,零中心归一化瞬时幅度绝对值的标准偏差,零中心非弱信号段瞬时相位非线性分量绝对值标准偏差,零中心非弱信号段瞬时相位非线性分量标准偏差,零中心归一化的非弱信号段瞬时频率绝对值的标准偏差,一个信号段的归一化瞬时频率功率谱密度的最大值,根据信号 QPSK 和16QAM在 XI 轴投影的不同表现,提出特征参数。

These factors have seriously influenced the security and economical operation of the unit. This paper firstly summarizes the research background and the general situation of resarch about the overheating problem of boiler's high-temperature surface ,introduces the aspects and research findings in this field such as flux deviation、thermal deviation、flue gas velocity deviation at the exit of furnace and tee bends,et al.Then analyses the reason why high-temperature surfaces are overheated from such aspects as design、manufacture、operation, et al and points out one of the main factors that cause the overheating of reheaters is the flue gas velocity deviation caused by the remaining turning at the exit of furnace.

本文首先综合论述了课题的研究背景和目前电站锅炉高温受热面超温问题的研究概况,介绍了国内外流量偏差、热偏差、炉膛出口残余旋转、&三通&等研究方向和研究成果,然后从锅炉的设计、制造、运行等方面分析了高温再热器超温的原因,指出水平烟道内气流的残余旋转是造成再热器超温的主要原因之一。

Included are the measurements of the tooth profile deviation of a shaving cutter based on the generalized polar coordinate method, and of the helix deviation of the shaving cutter using curvature method to automatically identify the boundary points; the measurements of the tooth profile of a modified hobbing cutter, and of deviation of contact line of the hobbing cutter by means of the generalized cylindrical coordinate method; the measurement of the deviation of tooth profile of a non-linear worm .

这些测量包括:①基于广义极坐标法的剃齿刀齿廓误差测量,以及采用&曲率法&自动识别界点的剃齿刀螺旋线误差的测量;②修形滚刀的齿廓测量,以及基于广义圆柱坐标法的滚刀啮合误差的测量;③非线性蜗杆的齿廓误差测量。

The results show that when the test portion weight of the proof gold and samples is reduced to 160.00~200.00mg, there has no influence on the result of gold content. Respectively using magnesium oxide and bone ash cupels, the result deviation of gold content in the samples is within the allowable deviation of the national standards. The result of gold content in samples is much more closed to the theoretical value by adding proper copper in the proof gold. The additive amount of silver (2.5 to 2.7 times equal to the weight of the proof gold) in the proof gold and samples has no influence on the result of gold content.

结果表明,当标准Au与样品的称样量降为160.00~200.00mg时不影响其含Au量的分析结果;分别使用镁砂灰皿和骨灰灰皿,样品含Au量的分析结果与理论含Au量的偏差均在国家标准的允差范围内;标准Au中加入适量的Cu后测得样品的含Au量更接近于其理论含Au量;标准Au与样品中Ag的加入量(2.5~2.7倍Au质量)对样品含Au量分析结果的影响不大。

Input power in the technical parmeters list is average power of the allowable power calculated from the antigluing capability of gear contact strength and the allowable power calculated from the antibending capability of the teeth of cogwheel of the turbine.

技术参数表中的"输入功率";是按齿轮接触强度"抗胶合能力"计算的许用功率和按蜗轮轮齿"抗弯曲能力"计算的许用功率二者的平均功率。

The allowable processing length of the wooden sticks is 60mm to 1800mm, the allowable diameter is 15mm to 120mm and the length and diameter can be customized according to the requirements of the customers. For instance, we can deal with the drilling, processing of the round wood, American-style screw thread and Italian-style screw thread to meet the different demands by the customers.

木柄类产品可加工的长度是60 MM-1800 MM ,可加工的直径是15 MM-120 MM,长度和直径都可以根据客户的要求定做,例如钻孔、加工圆头、美式螺纹、意大利式螺纹等,满足客户的众多需求。

第1/100页 1 2 3 4 5 6 7 8 9 ... > 尾页
相关中文对照歌词
The Congregation
Power To The Peaceful
If A Girl Isn't Pretty
Evolution
If A Girl Isn't Pretty
Electric Barbarella
The Power And The Glory Hole
Dickie's Such An Asshole (The San Clemente Magnetic Deviation)
Gilded Lily
The Immaculate Conception
推荐网络例句

Farmers and ranchers are providing land to turbine owners or, in some cases, owning the equipment themselves.

农民和大牧场主正在向涡轮机主人提供土地。或者在一些情况下,他们自己拥有设备。

"This is a wonderful place. I will come back and visit it often."

"这是一个精彩的地方,我一定要经常来参观。"

He drew two five-franc pieces from his money-bag and handed them to the priest.

他从他钱袋里取出两枚五法郎的钱,交给神甫。